oil change YAMAHA MAJESTY 125 2007 Owners Manual

EAU10980
Indicator lights
1. Alarm indicator light
2. Left turn signal indicator light “c”
3. High beam indicator light “j”
4. Coolant temperature warning light “y”
5. Right turn signal indicator light “d”
EAU11030
Turn signal indicator lights “c” and
“
d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAUM1070
Oil change indicator
At the initial 500 km (300 mi) and
every 3000 km (1800 mi) thereafter,
the message “CHnGE OIL” appears
in the odometer/clock display to indi-
cate that the engine oil should be
changed. (See page 6-9.)
EAUM1080
Coolant temperature warning light
“
y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
The electrical circuit of the warning
light can be checked according to the
following procedure.
1. Turn the key to “h”.
2. If the warning light does not
come on, have a Yamaha dealer
check the electrical circuit.
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAUS1361
Speedometer unit
1. "TRIP" button
2. Multi-function display
3. Speedometer
4. Red zone
The speedometer unit is equipped
with the following:
a speedometer (which shows the
riding speed)
ECAS0010
CAUTION:
Do not operate the scooter in the
speedometer red zone.Red zone:
120 km/h (75 mph) and above
an odometer (which shows the
total distance traveled)
a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
12 3
y
4
y
12345
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
5D8-F8199-E0.qxd 1/6/07 16:20 Página 16

150 ~ 500 km (90 ~ 300 mi)
Avoid prolonged operation above 1/2
throttle.
Rev the engine freely through the
gears, but do not use full throttle at
any time.
500 ~ 1000 km (300 ~ 600 mi)
Avoid prolonged operation above 3/4
throttle.
ECA10350
CAUTION:
After 1000 km (600 mi) of operation,
the engine oil must be changed and
the oil strainer cleaned.
1000 km (600 mi) and beyond
Avoid prolonged full-throttle opera-
tion. Vary the speed occasionally.
ECA10270
CAUTION:
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
EAU17200
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EWA10310
s s
WARNING
Since the engine and exhaust
system can become very hot,
park in a place where pedes-
trians or children are not likely
to touch them.
Do not park on a slope or on
soft ground, otherwise the
vehicle may overturn.5
OPERATION AND IMPORTANT RIDING POINTS
5-4
5D8-F8199-E0.qxd 1/6/07 16:20 Página 35

ODOMETER READING (x 1000 Km)
ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB
1 6 12 18 24CHECK
8*Rear brake• Check operation, fluid level and vehicle for fluid leakage.√√ √ √√ √• Replace brake pads. Whenever worn to the limit
9*Brake hoses• Check for cracks or damage.√√√√ √• Replace. Every 4 years
10 *Wheels• Check runout and for damage.√√√√
• Check tread depth and for damage.
11 *Tires• Replace if necessary.
√√√√ √
• Check air pressure.
• Correct if necessary.
12 *Wheel bearings• Check bearing for looseness or damage.√√√√
13 *Steering bearings• Check bearing play and steering for roughness.√√ √ √√• Lubricate with lithium-soap-based grease. Every 20000 km
14 *Chassis fasteners• Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
15Sidestand, centerstand• Check operation.
• Lubricate.√√√√ √
16 *Sidestand switch• Check operation.√√ √ √√ √
17 *Front fork• Check operation and for oil leakage.√√√√
18 *Shock absorber
• Check operation and shock absorbers for oil leakage.√√√√
assemblies
19 *Carburetor• Adjust engine idling speed.√√ √ √√ √
• Change. (See page 6-9.)√When the oil change indicator light
20Engine oilcomes on (every 3000 km)
• Check oil level and vehicle for oil leakage. Every 3000 km√
21 *Engine oil strainer• Clean.√√√
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
5D8-F8199-E0.qxd 1/6/07 16:20 Página 39

ODOMETER READING (x 1000 Km)
ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB
1 6 12 18 24CHECK
22 *Cooling system• Check coolant level and vehicle for coolant leakage.√√√√ √
• Change. Every 3 years
• Check vehicle for oil leakage.
23Final transmission oil• Initial 500 km√√
• Change.√√
24 *V-belt• Replace. Every 10000 km
25 *Front and rear brake
• Check operation.√√ √ √√ √
switches
26Moving parts and cables• Lubricate.√√√√ √
Throttle grip housing • Check operation and free play.
27 * • Adjust the throttle cable free play if necessary.√√√√ √
and cable
• Lubricate the throttle grip housing and cable.
28 *Mufflers and exhaust
pipes• Check the screw clamps for looseness.√√ √ √√ √
29 *Lights, signals and • Check operation.
switches• Adjust headlight beam.√√ √ √√ √
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
EAUM2070
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
5D8-F8199-E0.qxd 1/6/07 16:20 Página 40

EAUM1260
Engine oil
The engine oil level should be chec-
ked before each ride. In addition, the
oil must be changed at the intervals
specified in the periodic maintenance
and lubrication chart
and when the oil change indicator
display comes on.
To check the engine oil level
1. Place the scooter on the centers-
tand.
NOTE:
Make sure that the scooter is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
1. Engine oil filler cap
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (wit-
hout screwing it in), and then
remove it again to check the oil
level.
1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil
1. Start the engine, warm it up for
several minutes, and then turn it
off.
1
2
3
4
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
5D8-F8199-E0.qxd 1/6/07 16:20 Página 44

2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
1. Engine oil drain bolt
2. Washer
4. Check the washer for damage
and replace it if necessary.
5. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
6. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECA11670
CAUTION:
Do not use oils with a diesel
specification of “CD” or oils of
a higher quality than specified.
In addition, do not use oils
labeled “ENERGY CONSER-
VING II” or higher.
Be sure no foreign material
enters the crankcase.
7. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
8. Reset the oil change indicator
display according to the follo-
wing procedure.
To reset the oil change indicator
display
1. Push and hold the "TRIP" button
for a MAXIMUM of three
seconds. While pushing the
"TRIP" button, turn the key to
"f".
Recommended engine oil:
See page 8-1.
Oil change quantity:
1.2 L (1.27 US qt) (1.06 Imp.qt)
Tightening torque:
Engine oil drain bolt:
32 Nm (3.2 m•kgf, 23.1 ft•lbf)
2
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
5D8-F8199-E0.qxd 1/6/07 16:20 Página 45

2. Release the "TRIP" button and
the oil change indicator light will
go off.
3. Turn the key to "e".
NOTE:
If the engine oil is changed before the
oil change indicator light comes on
(i.e. before the periodic oil change
interval has been reached), the indi-
cator light must be reset after the oil
change for the next periodic oil chan-
ge to be indicated at the correct time.
To reset the oil change indicator light
before the periodic oil change interval
has been reached, follow the above
procedure, but note that the indicator
light will come on for 1.4 seconds
after releasing the reset button, other-
wise repeat the procedure.
EAU20061
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final trans-
mission oil must be changed as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Start the engine, warm up the
final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the centers-
tand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
1. Final trasmission oil filler cap
1. Final transmission oil drain bolt
4. Remove the oil filler cap and
drain bolt to drain the oil from the
final transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
5D8-F8199-E0.qxd 1/6/07 16:20 Página 46

6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten
the oil filler cap.
EWA11310
s s
WARNING
Make sure that no foreign
material enters the final trans-
mission case.
Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU20101
To check the coolant level
1. Place the vehicle on the centers-
tand.
NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
1. Maximum level mark
2. Minimum level mark
2. Check the coolant level in the
coolant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.15 L (0.16 US qt) (0.88 Imp.qt)
Tightening torque:
Final transmission oil drain bolt:
22 Nm (2.2 m•kgf, 15.9 ft•lbf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
5D8-F8199-E0.qxd 1/6/07 16:20 Página 47

when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22720
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the brake
master cylinder and caliper as well as
the brake hose replaced at the inter-
vals listed below or whenever they are
damaged or leaking.
Oil seals: Replace every two
years.
Brake hose: Replace every four
years.
EAU23100
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
Recommended lubricant:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5D8-F8199-E0.qxd 1/6/07 16:20 Página 56

DimensionsOverall length
2030 mm (79.9 in)
Overall width
745 mm (29.3 in)
Overall height
1285 mm (50.6 in)
Seat height
774 mm (30.5 in)
Wheelbase
1480 mm (58.2 in)
Ground clearance
102 mm (4.01 in)
Minimum turning radius
3840 mm (151.2 in)
WeightWith oil and fuel
148 kg (326 lb)
EngineEngine type
Liquid cooled 4-stroke, SOHC
Cylinder arrangement
Forward-inclined single cylinder
Displacement
124.1 cm
3(7.57 cu.in)
Bore x stroke
53.7 x 54.8 mm (2.11 x 2.15 in)
Compression ratio
11:1
Starting system
Electric starter
Lubrication system
Wet sump
Engine oilType
SAE10W30 or SAE10W40
Recommended engine oil grade
API service SE, SF, SG type or higher
Engine oil quantityPeriodic oil change
1.2 L (1.27 US qt) (1.06 Imp.qt)
Final transmission oilType
YAMALUBE 4 (10W30) of SAE10W30
type SE motorolie
Quantity
0.15 L (0.16 US qt) (0.88 Imp.qt)
Cooling systemRadiator capacity (including all routes)
1.20 L (1.27 US qt) (1.06 Imp.qt)
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.30 L (0.32 US qt) (0.26 Imp.qt)
Air filterAir filter element
Dry element
Recommended fuelRecommended fuel
Unleaded fuel
Fuel tank capacity
10.5 L ( 2.77US gal) (2.31 Imp.gal)
Fuel reserve amount
3 L (0.79 US gal) (0.66 Imp gal)
CarburetorManufacturer
TEIKEI
Type x quantity
TK28 x 1
Spark plug (s)Manufacturer/model
NGK / CR8E
Spark plug gap
0.7 - 0.8 (0.028 - 0.031 in)
ClutchClutch type
Dry, automatic centrifugal
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
40/15 (2.666)
Secondary reduction system
Helical gear
Secondary reduction ratio
40/15 (2.666)
Transmission type
V-belt automatic
8
SPECIFICATIONS
8-1
5D8-F8199-E0.qxd 1/6/07 16:20 Página 73