warning YAMAHA MAJESTY S 125 2015 Owner's Guide

PERIODIC MAINTENANCE AND ADJUSTMENT
6-24
2
3
4
567
8
9
in a possible loss of control.
EAU23273
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake, push down hard on the handlebars several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-pair it.
Recommended lubricant:
Lithium-soap-based grease



PERIODIC MAINTENANCE AND ADJUSTMENT
6-25
1
2
3
4
56
7
8
9
EAU45512
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.1. Place the vehicle on the center- stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over.
[EWA10752]
2. Hold the lower ends of the front fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
EAU23292
Checking the w heel bearingsThe front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.
EAUT4120
BatteryThe battery is located behind panel A.
(See page 6-8.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to be
checked and, if necessary, securely
tightened.
WARNING
EWA10761

Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
1. Battery
1



PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
1
2
3
4
56
7
8
9
EAUT4220
Replacing the fusesMain fuse
The main fuse is located behind panel
A. (See page 6-8.)
If the main fuse is blown, replace it as
follows.1. Turn the key to “OFF”.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.
[EWA15132]
3. Turn the key to “ON” to check if the vehicle operates normally. If the
main fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
4. After removing and installing the
main fuse, turn the main switch
from “ON” to “OFF” three times in
three-second intervals to initialize
the idle speed control system.
Fuse box
The fuse box, which contains the fuses
for the ignition, turn signal, and lighting
systems, as well as the back-up fuse
for the multi-function meter unit, is lo-
cated underneath the windshield be-
hind the front cowling. Have a Yamaha
dealer check and replace these fuses if
necessary.
1. Main fuse
1
Specified fuses: Main fuse: 20.0 A
Specified fuses:Lighting fuse: 15.0 A
Signaling system fuse:
7.5 A× 2
Ignition fuse: 7.5 A
Backup fuse: 7.5 A



PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
2
3
4
567
8
9
EAUT4110
Replacing a license plate light
bulb1. Remove the license plate light bulbsocket (together with the bulb) by
turning it counterclockwise, and
then pulling it out.
2. Remove the burnt-out bulb by pull- ing it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with the bulb) by pushing it in, and then turn
it clockwise until it stops.
EAU54501
Auxiliary lightThis model is equipped with LED-type
auxiliary lights.
If an auxiliary light does not come on,
have a Yamaha dealer check it.
EAU25882
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
1. License plate light bulb socket
1



PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
1
2
3
4
56
7
8
9Engine overheating
WARNING
EWAT1041

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily us
ed instead, provided that it is changed to the recommended coolantas soon as possible.Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.



SCOOTER CARE AND STORAGE
7-3
2
3
4
5
678
9
After cleaning
1. Dry the scooter with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean- er to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be- fore storing or covering it.
WARNING
EWA10943
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent.

Before operating the scooter
test its braking performanceand cornering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.



SCOOTER CARE AND STORAGE
7-4
1
2
3
4
5
67
8
9
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the scoot-
er.NOTICE
ECA10821

Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your scooter for several
months: 1. Follow all the instructions in the “Care” section of this chapter. 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 ° C (30 °F) or more than 30
° C (90 °F)]. For more information
on storing the battery, see page
6-25.TIPMake any necessary repairs beforestoring the scooter.



SPECIFICATIONS
8-3
2
3
4
5
6
789
Meter lighting:LED
High beam indicator light:
LED
Turn signal indicator light: LED
Coolant temperature warning light: LED
Engine trouble warning light:
LEDFuses:Main fuse:20.0 A
Signaling system fuse:
7.5 A× 2
Ignition fuse: 7.5 A
Backup fuse: 7.5 A



INDEXAAcceleration and deceleration....................5-2
Air filter and V-belt case air filter
elements ................................................6-15
Auxiliary light ............................................6-30BBattery......................................................6-25
Brake fluid, changing ...............................6-22
Brake fluid level, checking .......................6-21
Brake lever, front........................................3-7
Brake lever, rear ........................................3-7
Brake levers, lubricating...........................6-23
Braking .......................................................5-3CCables, checking and lubricating .............6-22
Care ...........................................................7-1
Catalytic converter ...................................3-10
Centerstand and sidestand, checking and
lubricating ..............................................6-23
Coolant.....................................................6-13
Coolant temperature warning light .............3-3DDimmer switch ...........................................3-7EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil .................................................6-10
Engine serial number .................................9-1
Engine trouble warning light.......................3-3FFinal transmission oil ...............................6-12
Front and rear brak e lever free play,
checking ................................................6-20
Front and rear brake pads, checking .......6-20 Front fork, checking ................................. 6-24
Front turn signal light ............................... 6-28
Fuel............................................................ 3-8
Fuel consumption, tips
for reducing........... 5-3
Fuel gauge................................................. 3-4
Fuel tank breather hose and overflow hose ........................................................ 3-9
Fuel tank cap ............................................. 3-8
Fuses, replacing ...................................... 6-27
HHandlebar switches ................................... 3-6
Headlight bulb, replacing ......................... 6-28
Helmet holder .......................................... 3-11
High beam indicator light ........................... 3-2
Horn switch ................................................ 3-7IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-15
Indicator lights and warning lights ............. 3-2KKeyhole cover ............................................ 3-2LLicense plate light bulb, replacing ........... 6-30
Luggage hook .......................................... 3-14MMain switch/steering lock........................... 3-1
Maintenance and lubrication, periodic ....... 6-5
Maintenance, emission control system...... 6-4
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................. 3-4PPanels, removing and installing ................. 6-8
Parking ...................................................... 5-4 Part locations ............................................ 2-1
Passenger footrest .................................. 3-11
Pass switch ............................................... 3-7
SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-10
Shock absorber assembly ....................... 3-13
Sidestand ................................................ 3-14
Spark plug, checking ................................. 6-9
Specifications ............................................ 8-1
Starting off ................................................. 5-2
Starting the engine .................................... 5-1
Start switch................................................ 3-7
Steering, checking................................... 6-25
Storage...................................................... 7-4
Storage compartments ............................ 3-12TTachometer ............................................... 3-3
Tail/brake light ......................................... 6-28
Throttle grip and cable, checking and
lubricating ............................................. 6-22
Throttle grip free play, checking .............. 6-17
Tires ........................................................ 6-17
Tool kit....................................................... 6-2
Troubleshooting ...................................... 6-30
Troubleshooting charts............................ 6-32
Turn signal indicator lights ........................ 3-2
Turn signal light bulb (rear), replacing..... 6-29
Turn signal switch ..................................... 3-7VValve clearance....................................... 6-17
Vehicle identification number .................... 9-1