brake light YAMAHA MT-10 2016 User Guide

[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2016, Model line: MT-10, Model: YAMAHA MT-10 2016
Pages: 110, PDF Size: 9.15 MB

Load previous 10 pages

Page 98 of 110

YAMAHA MT-10 2016 User Guide Motorcycle care and storage
8-2
1
2
3
4
5
6
78
9
10
11
12 water and diluted mild detergent
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic pa

Motorcycle care and storage
8-2
1
2
3
4
5
6
78
9
10
11
12 water and diluted mild detergent
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts or the
muffler. Be sure to avoid using
cloths or sponges which have
been in contact with strong or
abrasive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or electro-
lyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
storage compartments, electric
components (couplers, connec-
tors, instruments, switches and
lights), breather hoses andvents.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.TIPSalt sprayed on roads in the winter mayremain well into spring.
1. Clean the motorcycle with cold wa- ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10792]
2. After drying the motorcycle, apply a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces (except the tita-
nium muffler) to prevent corrosion.
Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield with
a cloth or sponge dampened with a
neutral detergent, and after cleaning,
thoroughly wash it off with water. For
additional cleaning, use Yamaha Wind-
shield Cleaner or other quality cleaner.
Some cleaning compounds for plastics
may leave scratches on surfaces of the
windshield. Before using them, make a
test by polishing an area which does
not affect your visibility.
Cleaning the titanium mufflerThis model is equipped with a titanium
muffler, which requires the following
special care.
Use only a soft, clean cloth or
sponge with mild detergent and
water to clean the titanium muffler.
However, if the muffler cannot be
thoroughly cleaned with mild de-
B67-9-E0.book 2 ページ２０１６年２月２９日　月曜日　午前９時３０分

Page 99 of 110

YAMAHA MT-10 2016 User Guide Motorcycle care and storage
8-3
1
2
3
4
5
6
789
10
11
12
tergent, alkaline products and a
soft brush may be used.

Never use compounds or other
special treatments to clean the tita-
nium muffler, a

Motorcycle care and storage
8-3
1
2
3
4
5
6
789
10
11
12
tergent, alkaline products and a
soft brush may be used.

Never use compounds or other
special treatments to clean the tita-
nium muffler, as they will remove
the finish on the outer surface of
the muffler.

Even the smallest amounts of oil,
such as from oily towels or finger-
prints, will leave stains on the tita-
nium muffler, which can be
removed with a mild detergent.

Note that the thermally induced
discoloring of the portion of the ex-
haust pipe leading into the titanium
muffler is normal and cannot be re-
moved.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts.
4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar- ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
B67-9-E0.book 3 ページ２０１６年２月２９日　月曜日　午前９時３０分

Page 102 of 110

YAMAHA MT-10 2016 User Guide Specifications
9-2
1
2
3
4
5
6
7
89
10
11
12
5th: 1.381 (29/21)
6th:
1.250 (30/24)
Chassis:Frame type: Diamond
Caster angle:
24.0 
Trail: 102 mm (4.0 in)Front tire:Type:
Tubeless
Size: 120/70ZR17M

Page 103 of 110

YAMAHA MT-10 2016 User Guide Specifications
9-3
1
2
3
4
5
6
7
8910
11
12
Brake/tail light:LED
Front turn signal light:
LED
Rear turn signal light: LED
Auxiliary light: LED
License plate light:
LED
Meter lighting: LED
Neutral indi

Page 106 of 110

YAMAHA MT-10 2016 User Guide 11-1
1
2
3
4
5
6
7
8
9
1011
12
IndexAABS ....................................................... 4-18
ABS warning light.................................... 4-7
Air filter element .....................

11-1
1
2
3
4
5
6
7
8
9
1011
12
IndexAABS ....................................................... 4-18
ABS warning light.................................... 4-7
Air filter element .................................... 7-17
Auxiliary DC jack ................................... 4-28BBattery................................................... 7-30
Brake and clutch levers, checking and lubricating .................................... 7-28
Brake and shift pedals, checking
and lubricating .................................... 7-27
Brake fluid, changing ............................ 7-24
Brake fluid level, checking .................... 7-23
Brake lever ............................................ 4-17
Brake lever free play, checking ............. 7-21
Brake light switches .............................. 7-22
Brake pedal ........................................... 4-18CCables, checking and lubricating .......... 7-26
Canister................................................. 7-10
Care ........................................................ 8-1
Catalytic converter ................................ 4-21
Clutch lever ........................................... 4-16
Clutch lever free play, adjusting ............ 7-21
Coolant.................................................. 7-13
Coolant temperature warning light .......... 4-6
Cruise control indicator lights .................. 4-6
Cruise control switches ........................... 4-4
Cruise control system ............................. 3-1DDiagnostic connector ............................ 10-2
Dimmer/Pass switch ............................... 4-4
D-mode (drive mode) .............................. 3-3
Drive chain, cleaning and lubricating .... 7-26 Drive chain slack .................................. 7-24
Drive mode switch .................................. 4-4
EEngine break-in ...................................... 6-3
Engine idling speed, checking .............. 7-17
Engine oil and oil fi
lter cartridge ........... 7-10
Engine serial number............................ 10-1
Engine trouble warning light ................... 4-6
EXUP system ....................................... 4-27FFront and rear brake pads, checking .... 7-22
Front fork, adjusting .............................. 4-23
Front fork, checking .............................. 7-29
Fuel....................................................... 4-20
Fuel consumption, tips for reducing........ 6-3
Fuel tank cap ........................................ 4-19
Fuel tank overflow hose........................ 4-21
Fuses, replacing ................................... 7-32HHandlebar switches ................................ 4-3
Hazard switch ......................................... 4-4
High beam indicator light ........................ 4-5
Horn switch ............................................. 4-4IIdentification numbers .......................... 10-1
Ignition circuit cut-off system ................ 4-29
Immobilizer system ................................. 4-1
Immobilizer system indicator light........... 4-8
Indicator lights and warning lights .......... 4-5LLuggage strap holders .......................... 4-27MMain switch/steering lock........................ 4-2
Maintenance and lubrication, periodic .... 7-5 Maintenance, emission control system ... 7-3
Matte color, caution ................................. 8-1
Model label ............................................ 10-2
Multi-function meter unit .......................... 4-8
NNeutral indicator light .............................. 4-5OOil pressure warning light........................ 4-5PParking .................................................... 6-4
Part locations .......................................... 2-1SSafety information ................................... 1-1
Seat ....................................................... 4-22
SELECT switch ....................................... 4-4
Shifting .................................................... 6-2
Shift pedal ............................................. 4-17
Shift timing indicator light ........................ 4-7
Shock absorber assembly, adjusting .... 4-24
Sidestand .............................................. 4-28
Sidestand, checking an
d lubricating...... 7-28
Spark plugs, checking ............................. 7-9
Special features ...................................... 3-1
Specifications .......................................... 9-1
Starting the engine .................................. 6-1
Steering, checking................................. 7-30
Steering damper warning light ................ 4-7
Stop/Run/Start switch.............................. 4-4
Storage.................................................... 8-4
Supporting the motorcycle .................... 7-35
Swingarm pivots, lubricating ................. 7-29TThrottle grip and cable, checking and lubricating ........................................... 7-27
B67-9-E0.book 1 ページ２０１６年２月２９日　月曜日　午前９時３０分

Page: < prev 1-10 11-20