MPG YAMAHA MT-10 2018 Owners Manual

Instrument and control functions
4-13
1
2
34
5
6
7
8
9
10
11
12 Push the “SELECT” switch to switch the
display between the odometer mode
“ODO”, tripmeter modes “TRIP 1” and
“TRIP 2”, instantaneous fuel consump-
tion mode “km/L” or “L/100 km”, aver-
age fuel consumption mode “AVE – –.–
km/L” or “AVE – –.– L/100 km” in the fol-
lowing order:
ODO
 TRIP 1  TRIP 2  km/L or
L/100 km  AVE – –.– km/L or AVE –
–.– L/100 km  ODO
When set to miles:
ODO  TRIP 1  TRIP 2  MPG 
AVE – –.– MPG  ODO
If the last segment of the fuel meter starts flashing, the display automatical-
ly changes to the fuel reserve tripmeter
mode “TRIP F” and starts counting the
distance traveled from that point. In this
case, push the “SELECT” switch to
switch the display in the following order:
TRIP F
 km/L or L/100 km  AVE –
–.– km/L or AVE – –.– L/100 km 
ODO  TRIP 1  TRIP 2  TRIP F
When set to miles:
TRIP F  MPG  AVE – –.– MPG 
ODO  TRIP 1  TRIP 2  TRIP F
TIP
To reset a tripmeter, select it by
pushing the “SELECT” switch, and
then push the “RESET” button for
two seconds.

If you do not reset the fuel reserve
tripmeter manually, it resets auto-
matically and disappears after re-fueling and traveling 5 km (3 mi). Instantaneous fuel consumption
mode
The instantaneous fuel consumption
display can be set to either “km/L”,
“L/100 km” or “MPG” (when the
multi-function meter unit has been
set to miles).

“km/L”: The distance that can be
traveled on 1.0 L of fuel under the
current riding conditions is shown.

“L/100 km”: The amount of fuel
necessary to travel 100 km under
the current riding conditions is
shown.

“MPG”: The distance that can be
traveled on 1.0 Imp.gal of fuel un-
der the current riding conditions is
1. Select switch “SELECT”
R
ESSE T
PAS
S
TCS
SELECT
1
1. Instantaneous fuel consumption display
1
B67-9-E2.book 13 ページ ２０１８年６月５日　火曜日　午前９時７分

Instrument and control functions
4-14
1
2
345
6
7
8
9
10
11
12
shown.
To switch between the “km/L” and
“L/100 km”, push the “CLOCK” and
“RESET” buttons at the same time.
TIPIf traveling at speeds under 20 km/h (12mi/h), “– –.–” is displayed.
Average fuel consumption mode
This display shows the average fuel
consumption since it was last reset.
The average fuel consumption display
can be set to either “AVE – –.– km/L”,
“AVE – –.– L/100 km” or “AVE – –.–
MPG” (when the multi-function meter
unit has been set to miles).

“AVE – –.– km/L”: The average
distance that can be traveled on
1.0 L of fuel is shown.

“AVE – –.– L/100 km”: The aver-
age amount of fuel necessary to
travel 100 km is shown.

“AVE – –.– MPG”: The average
distance that can be traveled on
1.0 Imp.gal of fuel is shown.
To switch between the “km/L” and
“L/100 km”, push the “CLOCK” and
“RESET” buttons at the same time.
To reset the average fuel consumption,
push the “RESET” button for two sec-
onds.
TIPAfter resetting the average fuel con-
sumption, “– –.–” will be shown until the
vehicle has traveled a sufficient dis-tance. Brightness and shift indicator light
control mode
This mode cycles through five control
functions, allowing you to make the fol-
lowing settings in the order listed be-
low.

Screen brightness:
This function allows you to adjust
the brightness of the screen.

Shift indicator light style:
This function allows you to set the
indicator light to on, flash, or off.

Shift indicator light on r/min:
This function allows you to select
the engine speed at which the indi-
cator light will be activated.

Shift indicator light off r/min:
1. Average fuel consumption display
1
1. Brightness level display
1
B67-9-E2.book 14 ページ ２０１８年６月５日　火曜日　午前９時７分