remove seats YAMAHA MT09 TRACER 2017 Owners Manual

Instrument and control functions
3-28
1
234
5
6
7
8
9
10
11
12
EAU65800
SeatsPassenger seat
To remove the passenger seat1. Insert the key into the seat lock, and then turn it counterclockwise.
2. Lift the front of the passenger seat and pull it forward.
To install the passenger seat1. Insert the projections on the rear of the passenger seat into the seat
holders as shown, and then push
the front of the seat down to lock it
in place. 2. Remove the key.
Rider seat
To remove the rider seat
1. Remove the passenger seat.
2. Remove the cap, then push the rider seat lock lever, located under
the back of the rider seat, to the left
as shown, and then pull the seat
off. To install the rider seat
1. Install the cap with the arrow mark
facing forward.
2. Insert the projection on the front of the rider seat into the seat holder
as shown, and then push the rear
of the seat down to lock it in place.
1. Seat lock
2. Unlock.
1
2
1. Projection
2. Seat holder
1 2
1. Cap
2. Rider seat lock lever
2
1
2PP-9-E3.book 28 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-29
1
23
4
5
6
7
8
9
10
11
12 3. Install the passenger seat.
TIP
Make sure that the seats are prop-
erly secured before riding.

The rider seat height can be ad-
justed to change the riding posi-tion. (See the following section.)
EAU63050
Adjusting the rider seat heightThe rider seat height can be adjusted to
one of two positions to suit the rider’s
preference.
The rider seat height was adjusted to
the lower position at delivery.
To change the rider seat height to
the high position
1. Remove the passenger seat and rider seat. (See page 3-28.)
2. Remove the rider seat height posi- tion adjuster by pulling it upward. 3. Install the rider seat height position
adjuster by inserting the front pro-
jections into the grommets.
4. Insert the projection on the front of
1. Projection
2. Seat holder
2 1
1. Low position
2. High position
1
2
1. Rider seat height position adjuster
1. Rider seat height position adjuster
2. Projection
3. Grommet
1
1
2
3
3
2PP-9-E3.book 29 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-31
1
23
4
5
6
7
8
9
10
11
12 5. Align the projection on the bottom
of the rider seat with the “L” posi-
tion slot, and then push the rear of
the seat down to lock it in place as
shown.
6. Install the passenger seat.
TIPMake sure that the seats are properlysecured before riding.
EAU63060
Helmet holderThe helmet holder is located under the
passenger seat. A hel met holding cable
is provided in the owner’s tool kit to se-
cure a helmet to the helmet holder.
To secure a helmet to the helmet
holder 1. Remove the passenger seat. (See page 3-28.)
2. Pass the helmet holding cable through the buckle on the helmet
strap as shown, and then hook the
cable loops over the helmet hold-
er. 3. Place the helmet on the right side
of the vehicle, and then install the
seat. WARNING! Never ride with
a helmet attached to the helmet
holder, since the helmet may hit
objects, causing loss of control
and possibly an accident.
[EWA10162]
To release the helmet from the hel-
met holder
Remove the passenger seat, remove
the helmet holding cable from the hel-
met holder and the helmet, and then in-
stall the seat.
1. Projection
2. “L” position slot
1
2
1. Helmet
2. Helmet holding cable
3. Helmet holder
3
2
1
2PP-9-E3.book 31 ページ ２０１６年９月１３日　火曜日　午前９時７分