lock YAMAHA RHINO 660 2007 Owner's Guide

7-20
AVERTISSEMENT


Ne pas conduire le véhicule sur des pentes trop
raides ou trop difficiles pour ses compétences de
pilote. Le véhicule bascule plus facilement sur
des côtes dont la pente est extrêmement raide
que sur des surfaces de niveau ou des côtes à
pente douce. Pratiquer sur des côtes à pente plus
douce avant d’aborder des côtes à pente plus
raide.


Ne pas traverser une colline latéralement. Gra-
vir les pentes tout droit.


Ne pas rouler sur des pentes dont l’inclinaison
est supérieure à 15°.
Avant de s’attaquer à une côte, s’assurer d’avoir sélec-
tionné la gamme basse et d’être en traction sur quatre
roues ou, si nécessaire, en traction sur quatre roues avec
différentiel bloqué. Une traction, un certain élan et une
accélération constante sont nécessaires pour gravir une
côte. Il faut donc rouler à une vitesse qui garantisse l’élan
nécessaire, mais qui permette toujours de réagir aux
changement de terrain. Ralentir lorsque l’on atteint le
sommet de la colline si l’on ne distingue pas clairement
l’autre versant, car il pourrait s’y trouver une personne,
un obstacle, voire même un ravin.
ADVERTENCIA

No conduzca nunca por pendientes dema-
siado pronunciadas para el vehículo o para
sus habilidades. El vehículo puede volvar
más fácilmente en pendientes muy pronun-
ciadas que en superficies llanas o pendien-
tes pequeñas. Practique en pendientes pe-
queñas antes de intentarlo en las grandes.


No circule de lado por una pendiente. Suba
en línea recta.


No utilice nunca el vehículo en pendientes
de más de 15°.
Antes de subir una pendiente, compruebe que esté
seleccionada la tracción integral (4WD) o, si es pre-
ciso, la tracción integral con bloqueo de diferencial
(4WD Diff. Lock). Para subir una pendiente necesita
tracción, impulso y aceleración sostenida. Avance
con la velocidad suficiente para mantener el impulso,
pero no tan elevada como para que le impida reac-
cionar ante las variaciones del terreno durante el as-
censo. Si al llegar a la cima no dispone de visibilidad
suficiente sobre el otro lado, reduzca la velocidad:
puede que haya gente, obstáculos o un barranco.
EE.book Page 20 Friday, August 4, 2006 12:02 PM

8-91
The brake fluid reservoir is located under the
hood. (See pages 8-17–8-19 for hood opening
and closing procedures.)
Observe these precautions:

When checking the fluid level, make sure the
top of the brake fluid reservoir is level.


Use only the recommended quality brake fluid.
Otherwise, the rubber seals may deteriorate,
causing leakage and poor braking perfor-
mance.


Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor braking performance.


Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock. Recommended brake fluid: DOT 4
EE.book Page 91 Friday, August 4, 2006 12:02 PM

8-99 1. Locknut 2. Adjusting nut
1. Contre-écrou 2.Écrou de réglage
1. Contratuerca 2. Tuerca de ajuste
5. Loosen the locknut.
6. Turn the adjusting nut in direction a to in-
crease the free play or in direction b to de-
crease the free play.
7. Tighten the locknut.
8. Install the console.
9. Install the seats.
EE.book Page 99 Friday, August 4, 2006 12:02 PM

8-119 1. Main fuse 2. Spare main fuse
3. Headlight fuse 4. Ignition fuse
5. Auxiliary DC jack fuse 6. Four-wheel-drive motor fuse
7. Signaling system fuse
8. Backup fuse (for odometer and clock)
9. Carburetor warmer fuse 10. Spare fuse (× 3)
1. Fusible principal 2. Fusible principal de rechange
3. Fusible des phares 4. Fusible d’allumage
5. Fusible de la prise pour accessoires
6. Fusible du moteur du dispositif quatre roues motrices
7. Fusible du système de signalisation
8. Fusible de sauvegarde (pour le compteur kilométrique et la montre)
9. Fusible du système de réchauffage de carburateur
10. Fusible de rechange (× 3)
1. Fusible principal 2. Fusible principal de repuesto
3. Fusible de los faros 4. Fusible del encendido
5. Fusible de la toma auxiliar de corriente continua
6. Fusible de la tracción integral
7. Fusible del sistema de intermitencia
8. Fusible de repuesto (cuentakilómetros y reloj)
9. Fusible del calentador del carburador
10. Fusible de reserva (× 3)
3. Remove the blown fuse, and then install a
new fuse of the specified amperage.
4. Turn the key to “ON” and turn on the electrical
circuit in question to check if the device oper-
ates.
5. If the fuse immediately blows again, have a
Yamaha dealer check the electrical system.
6. Install the battery compartment cover.
7. Close the hood.Specified fuses:
Main fuse: 30.0 A
Headlight fuse: 15.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Signaling system fuse: 10.0 A
Carburetor warmer fuse: 10.0 A
Four-wheel-drive motor fuse: 3.0 A
Backup fuse: 10.0 A
EE.book Page 119 Friday, August 4, 2006 12:02 PM

8-125 1. Headlight bulb holder
1. Porte-ampoule du phare
1. Portabombillas del faro
1. Do not touch the glass part of the bulb.
1. Ne pas toucher le verre de l’ampoule.
1. No tocar la parte de cristal de la bombilla.
4. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
5. Remove the defective bulb by pulling it out.
WARNING
A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool before touching or removing it. You can
be burned or a fire could start if the bulb touch-
es something flammable.6. Insert a new headlight bulb into the bulb hold-
er by pushing it in.CAUTION:
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
EE.book Page 125 Friday, August 4, 2006 12:02 PM

8-127
7. Install the bulb holder by pushing it in and
turning it clockwise.
8. Install the bulb holder cover and the cover at
the rear of the headlight.CAUTION:
Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seated
properly.9. Close the hood.
10. Adjust the headlight beam if necessary.
EE.book Page 127 Friday, August 4, 2006 12:02 PM

8-133 1. Quick fastener (× 8) 2. Bolt (× 2) 3. Panel A
1. Rivet démontable (× 8) 2. Vis (× 2) 3. Cache A
1. Fijación rápida (× 8) 2. Perno (× 2) 3. Panel A
1. Tail/brake light bulb holder
1. Porte-ampoule de feu arrière/stop
1. Portabombilla de la luz de freno/piloto trasero
2. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
3. Push the defective bulb in and turn it counter-
clockwise to remove it from the bulb holder.
4. Push a new bulb in and turn it clockwise to in-
stall in the bulb holder.
5. Install the bulb holder (together with the bulb)
by turning it clockwise.
EE.book Page 133 Friday, August 4, 2006 12:02 PM

9-1
EVU01550
1-CLEANING AND STORAGE
A. CLEANING
Frequent, thorough cleaning of your vehicle will
not only enhance its appearance but will improve
its general performance and extend the useful life
of many components.
1. Before cleaning the vehicle:
a. Block off the end of the exhaust pipe to pre-
vent water entry. A plastic bag and strong
rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, ap-
ply degreaser with a paint brush. Do not ap-
ply degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the
job.
EE.book Page 1 Friday, August 4, 2006 12:02 PM

9-9
3. Remove the spark plug, pour about one ta-
blespoon of SAE 10W30 or 20W40 motor oil
in the spark plug hole and reinstall the spark
plug. Ground the spark plug wire and turn the
engine over several times to coat the cylinder
wall with oil.
4. Lubricate all control cables.
5. Block up the frame to raise all wheels off the
ground.
6. Tie a plastic bag over the exhaust pipe outlet
to prevent moisture from entering.
7. If storing in a humid or salt-air atmosphere,
coat all exposed metal surfaces with a light
film of oil. Do not apply oil to any rubber parts
or the seat covers.
8. Remove the battery and charge it. Store it in
a dry place and recharge it once a month. Do
not store the battery in an excessively warm
or cold place [less than 0°C (30°F) or more
than 30°C (90°F)].NOTE:_ Make any necessary repairs before storing the ve-
hicle. _
EE.book Page 9 Friday, August 4, 2006 12:02 PM

10-6
Bulb voltage, wattage × quantity:
Headlight 12 V 30.0 W/30.0 W × 2
Tail/brake light 12 V 5.0 W/21.0 W × 2
Indicator lights:
Neutral indicator light LED
Reverse indicator light LED
Coolant temperature warning light LED
Parking brake indicator light LED
On-Command four-wheel-drive/differential gear
lock indicatorLCD
High-range indicator light LED
Low-range indicator light LED
On-Command differential gear lock indicator light LED
Specified fuses:
Main fuse 30.0 A
Headlight fuse 15.0 A
Ignition fuse 10.0 A
Auxiliary DC jack fuse 10.0 A
Four-wheel-drive motor fuse 3.0 A
Carburetor warmer fuse 10.0 A
Signaling system fuse 10.0 A
Backup fuse 10.0 AModel YXR66FW
EE.book Page 6 Friday, August 4, 2006 12:02 PM