key battery YAMAHA RHINO 700 2010 Manuale de Empleo (in Spanish)

6-9

The engine can be started in any gear if the
brake pedal is applied. However, it is recom-
mended to shift into neutral before starting
the engine.
4. With your foot off the accelerator pedal, start
the engine by turning the key to “” (start).
If the engine fails to start, release the key, and then
try starting it again. Wait a few seconds before the
next attempt. Each attempt should be as short as
possible, to preserve battery energy. NOTICE: Do
not crank the engine more than 5 seconds on
each attempt, or starter damage could occur.
Wait at least 5 seconds between each opera-
tion of the electric starter to let it cool.
Do not turn the key to the “” (start) position with
the engine running; otherwise, damage to the
electric starter may result.
TIPFor maximum engine life, never accelerate hard
when the engine is cold!
EE.book Page 9 Monday, January 19, 2009 5:30 PM

8-117 1. Quick fastener screw (× 2)
2. Battery compartment cover
1. Vis à serrage rapide (× 2)
2. Couvercle du compartiment de la batterie
1. Tornillo de fijación rápida (× 2)
2. Tapa del compartimento de la batería
2
1
1. Negative battery lead (black)
2. Positive battery lead (red) 3. Battery band
1. Câble négatif de batterie (noir)
2. Câble positif de batterie (rouge) 3. Sangle de batterie
1. Cable negativo de la batería (negro)
2. Cable positivo de la batería (rojo) 3. Correa de la batería
1
2
3
To remove the battery
1. Turn the key to “” (off).
2. Open the hood. (See pages 8-17–8-19 for
hood opening and closing procedures.)
3. Remove the quick fastener screws.
4. Remove the battery compartment cover by
lifting it up and pulling it out.
5. Unhook the battery band.
6. Disconnect the negative battery lead first,
then the positive battery lead by removing
their bolt.
7. Pull the battery out of its compartment.
EE.book Page 117 Monday, January 19, 2009 5:30 PM

8-125 1. Jumper cable positive lead
1. Câble de démarrage positif
1. Cable auxiliar positivo
1
1. Jumper cable negative lead
2. Starter motor installation bolt
1. Câble de démarrage négatif
2. Vis de montage du démarreur
1. Cable auxiliar negativo
2. Perno de sujeción del motor de arranque
1
2
However, if the vehicle must be jump-started, pro-
ceed as follows.
1. Turn the key to “” (off).
2. Open the hood. (See pages 8-17–8-19 for
hood opening and closing procedures.)
3. Remove the battery compartment cover.
(See pages 8-113–8-121 for battery compart-
ment cover removal and installation proce-
dures.)
4. Remove the console. (See pages 8-21–8-23
for console removal and installation proce-
dures.)
5. Using a charged 12-volt battery, connect the
positive lead of the jumper cable to the posi-
tive terminal of the battery in the vehicle and
the other end of the positive lead to the posi-
tive terminal of the charged battery.
6. Connect the negative lead of the jumper ca-
ble to the negative terminal of the charged
battery and the other end of the negative lead
to the starter motor installation bolt.
EE.book Page 125 Monday, January 19, 2009 5:30 PM

8-129
5B410023
Fuse replacement
The main fuse, the fuel injection system fuse, the
EPS fuse, and the fuse box are located under the
hood.
If a fuse is blown, replace it as follows.
1. Turn the key to “” (off) and turn off the
electrical circuit in question.NOTICETo prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.2. Open the hood. (See pages 8-17–8-19 for
hood opening and closing procedures.)
3. Remove the battery compartment cover.
(See pages 8-113–8-121 for battery compart-
ment cover removal and installation proce-
dures.)
5EE.book Page 129 Monday, January 19, 2009 5:30 PM

8-133
5. Turn the key to “” (on) and turn on the
electrical circuit in question to check if the de-
vice operates. If the fuse blows again imme-
diately, have a Yamaha dealer check the
electrical system.
6. Reinstall the battery compartment cover.
7. Close the hood.
EE.book Page 133 Monday, January 19, 2009 5:30 PM