oil YAMAHA SLIDER 50 2007 User Guide

EAU00462
PERIODIC MAINTENANCE AND MINOR REPAIR
Periodic maintenance and lubrication chart ............ 6-2
Checking the spark plug ......................................... 6-5
Final transmission oil .............................................. 6-6
Cleaning the air filter element ................................. 6-7
Adjusting the carburetor .......................................... 6-8
Adjusting the throttle cable free play ....................... 6-8
Tires ........................................................................ 6-9
Cast wheels .......................................................... 6-11
Adjusting the front brake lever free play ............... 6-11
Adjusting the rear brake lever free play ................ 6-11
Checking the front brake pads
and rear brake shoes ............................................ 6-12
Checking the brake fluid level ............................... 6-13
Changing the brake fluid ....................................... 6-14
Checking and lubricating the cables ..................... 6-14
6 Checking and lubricating the throttle grip
and cable .............................................................. 6-15
Lubricating the front and rear brake levers ........... 6-15
Checking and lubricating the centerstand ............. 6-15
Checking the front fork .......................................... 6-16
Checking the steering ........................................... 6-16
Checking the wheel bearings ................................ 6-17
Battery ................................................................... 6-17
Replacing the fuse ................................................ 6-19
Replacing a headlight bulb .................................... 6-20
Replacing a front turn signal light bulb .................. 6-21
Replacing a rear turn signal light bulb or
the tail/brake light bulb .......................................... 6-21
Troubleshooting .................................................... 6-21
Troubleshooting chart ........................................... 6-22

PERIODIC MAINTENANCE AND MINOR REPAIR
6
6-3 •Check tread depth and for damage.
9 * Tires•Replace if necessary.
•Check air pressure.√√√√ √
•Correct if necessary.
10 * Wheel bearings•Check bearing for looseness or damage.√√√√11 * Steering bearings•Check bearing play and steering for roughness.√√√√√
•Lubricate with lithium-soap-based grease.Every 24,000 km
12 * Chassis fasteners•Make sure that all nuts, bolts and screws
√√√√ √are properly tightened.
13 Centerstand•Check operation.
√√√√ √•Lubricate.
14 * Front fork•Check operation and for oil leakage.√√√√
15 * Rear shock absorber
•Check operation and shock absorber for oil leakage.√√√√
assembly
16 * Carburetor•Adjust engine idling speed.√√√√√ √
17 * Autolube pump•Check operation.
√√√√
•Bleed if necessary.
18 Final transmission oil•Check vehicle for oil leakage.√√ √
•Change.√√√
19 * V-belt•Replace.Every 10,000 kmNO. Item
Check or maintenance job
ODOMETER READING (x 1,000 km)1ANNUAL
CHECK
6121824

PERIODIC MAINTENANCE AND MINOR REPAIR
6
12
ZAUM01531. Final transmission oil drain bolt
2. Final transmission oil filler cap
EAU04228
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several mi-
nutes, and then stop the engine.
2. Place the scooter on the
centerstand.3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
Tightening torque:
Final transmission oil drain bolt:
17 Nm (1.7 m
•kgf)
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
Recommended final transmission oil:
See page 8-1.
Oil quantity:
0.11 L
EWA00062
•
Make sure that no foreign
material enters the final trans-
mission case.
•
Make sure that no oil gets on
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
6-6

PERIODIC MAINTENANCE AND MINOR REPAIR
6
1
ZAUM0170
1
ZAUM0318
1
4 32ZAUM0156
1. Air filter case cover1. Air filter element
EAUM0071
Cleaning the air filter elementThe air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more
frequently if you are riding in unusually
wet or dusty areas.
1. Remove the air filter case cover
by removing the screws.2. Pull the air filter element out, clean
it with solvent, and then squeeze
the remaining solvent out.
EW000075
Use only a dedicated parts cleaning
solvent. To avoid the risk of fire or
explosion, do not use gasoline orsolvents with a low flash point.
EC000089
To avoid damaging the foam material,
handle it gently and carefully, and donot twist or wring it.3. Apply oil of the recommended
type to the entire surface of the
element, and then squeeze the
excess oil out.
NOTE :
The air filter element should be wet butnot dripping.
Recommended oil:
Engine oil
6-7

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU04502
Rear brake shoes
The rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to
disassemble the brake. To check the
brake shoe wear, check the position of
the wear indicator while applying the
brake. If a brake shoe has worn to the
point that the wear indicator reaches
the wear limit line, have a Yamaha dea-
ler replace the brake shoes as a set.
1
2
ZAUM00591. Wear indicator
2. Wear limit
1
ZAUM05271. Minimum level mark
6-13
EAU00732
Checking the brake fluid levelInsufficient brake fluid may allow air to
enter the brake system, possibly causing
it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads and/
or brake system leakage. If the brake
level is low, be sure to check the brake
pads for wear and the brake system for
leakage.Observe these precautions:
•
When checking the fluid level,
make sure that the top of the
master cylinder is level by turning
the handlebars.
•
Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.
Recommended brake fluid:
DOT 4
NOTE :
If DOT 4 is not available, DOT 3 can beused.•
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and lead
to poor braking performance.
•
Be careful that water does not en-
ter the master cylinder when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAUM0008
Changing the brake fluidHave a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and
lubrication chart. In addition, have the
brake hose replaced every four years
or whenever it is damaged or leaking.
EAU02962
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be
lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or replace
it.
Recommended lubricant:
Engine oil
EW000112
Damage to the outer sheath may
interfere with proper cable operation
and will cause the inner cable to
rust. Replace a damaged cable as
soon as possible to prevent unsafeconditions.
6-14
•
Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
•
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU02939
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
EW000115
Securely support the scooter so thatthere is no danger of it falling over.
Check the inner tubes for scratches,
damage and excessive oil leakage.To check the operation
1. Place the scooter on a level sur-
face and hold it in an upright po-
sition.
2. While applying the front brake,
push down hard on the
handlebars several times to check
if the front fork compresses and
rebounds smoothly.
EC000098
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check orrepair it.ZAUM0528
EAU00794
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine
to raise the front wheel off the
ground.
EW000115
Securely support the scooter so thatthere is no danger of it falling over.
6-16

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAUM0072
Replacing a headlight bulb1. Remove front cover by removing
the screws.
2. Remove the headlight coupler.3. Remove the headlight bulb holder
by turning it 1/4 turn
counterclockwise.
4. Remove the defective bulb.
EW000119
Headlight bulbs get very hot.
Therefore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it hascooled down.
5. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
1. Screw (x4)1. Headlight bulb holder
1
ZAUM0530
6-20
1
1
ZAUM0529
6. Connect the headlight coupler and
install the front cover.
EC000105
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely
affected. Thoroughly clean off any
dirt and fingerprints on the headlight
bulb using a cloth moistened withalcohol or thinner.

SCOOTER CARE AND STORAGE
7
CareWhile the open design of a scooter
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality
components are used. A rusty exhaust
pipe may go unnoticed on a car,
however, it detracts from the overall
appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors,
including the spark plug cap, are
tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.Cleaning
ECA00011
•
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are used
on hard-to-remove dirt, do not
leave the cleaner on the affected
area any longer than instructed.
Also, thoroughly rinse the area off
with water, immediately dry it, and
then apply a corrosion protection
spray.
•
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to clean
plastic.
•
Do not use any harsh chemical
products on plastic parts. Be sure
to avoid using cloths or sponges
which have been in contact with
strong or abrasive cleaning
products, solvent or thinner, fuel
(gasoline), rust removers or
inhibitors, brake fluid, antifreeze
or electrolyte.
7-1

SCOOTER CARE AND STORAGE
7After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is
recommended to apply a corro-
sion protection spray on all metal,
including chrome- and nickel-
plated, surfaces.
4. Use spray oil as a universal
cleaner to remove any remaining
dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely
before storing or covering it.
EWA00002
•
Make sure that there is no oil
or wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
•
Before operating the scooter
test its braking performanceand cornering behavior.
ECA00013
•
Apply spray oil and wax
sparingly and make sure to
wipe off any excess.
•
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
•
Avoid using abrasive polishing
compounds as they will wearaway the paint.
NOTE :
Consult a Yamaha dealer for advice onwhat products to use.
7-3