clock YAMAHA SLIDER 50 2008 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2008, Model line: SLIDER 50, Model: YAMAHA SLIDER 50 2008Pages: 80, PDF Size: 2.06 MB
Page 22 of 80
3
INSTRUMENT AND CONTROL FUNCTIONS
1
ZAUM0085
2 1
ZAUM0144
EAU00163
Rear brake leverThe rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the
handlebar grip.1. Rear brake lever
EAU03463
Fuel and 2-stroke engine oil
tank capsThe fuel tank cap and the 2-stroke
engine oil tank cap are located under
the seat. (See page 3-8 for seat
opening and closing procedures.)
Fuel tank cap
To remove the fuel tank cap, turn it
counterclockwise, and then pull it off.
To install the fuel tank cap, turn it
clockwise.2-stroke engine oil tank cap
To remove the 2-stroke engine oil tank
cap, pull it off.
To install the 2-stroke engine oil tank
cap, push it into the oil tank opening.
EW000025
Make sure that the fuel and 2-stroke
engine oil tank caps are properlyinstalled before riding the scooter.
1. Fuel tank cap
2. Oil tank cap
3-5
Page 57 of 80
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAUM0072
Replacing a headlight bulb1. Remove front cover by removing
the screws.
2. Remove the headlight coupler.3. Remove the headlight bulb holder
by turning it 1/4 turn
counterclockwise.
4. Remove the defective bulb.
EW000119
Headlight bulbs get very hot.
Therefore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it hascooled down.
5. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
1. Screw (x4)1. Headlight bulb holder
1
ZAUM0530
6-20
1
1
ZAUM0529
6. Connect the headlight coupler and
install the front cover.
EC000105
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely
affected. Thoroughly clean off any
dirt and fingerprints on the headlight
bulb using a cloth moistened withalcohol or thinner.
Page 58 of 80
PERIODIC MAINTENANCE AND MINOR REPAIR
6
2 1
ZAUM0531
1
2
ZAUM05321. Lens
2. Screw (x2)
6-21
EAU01623
Replacing the tail/brake light
bulb1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by
pushing it in and turning it
counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it
clockwise until it stops.
4. Install the lens by installing the
screws.
EC000108
Do not overtighten the screws,otherwise the lens may break.
EAU03497
Replacing a turn signal light
bulb1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it
counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it
clockwise until it stops.
4. Install the lens by installing the
screw.
ECA00065
Do not overtighten the screw,otherwise the lens may break.
EAU01008
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems
yourself. However, should your scoo-
ter require any repair, take it to a
Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
1. Screw
2. Lens