brake YAMAHA SR400 2014 Owner's Manual

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
1
2
3
4
56
7
8
9
10
11
12
EAU51951
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
Check the front fork for damage and ex-
cessive oil leakage.
To check the operation 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake, push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-pair it.
EAU45512
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.1. Place the vehicle on the center- stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over.
[EWA10752]
2. Hold the lower ends of the front fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
2RD-9-E0.book 27 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
1
2
3
4
567
8
9
10
11
12
2. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.
3. Unhook the headlight bulb holder, and then remove the burnt-out bulb.
4. Place a new headlight bulb into po- sition, and then secure it with the
bulb holder.
5. Install the bulb cover, and then connect the coupler.
6. Install the headlight unit by install- ing the screws.
7. Have a Yamaha dealer adjust the headlight beam if necessary.
EAU24134
Replacing the ta il/brake light
bulb1. Remove the tail/brake light lens by
removing the screws.
2. Remove the burnt-out bulb by pushing it in and turning it counter-
clockwise.
1. Screw
1. Headlight coupler
2. Headlight bulb cover
1
1
2
1. Headlight bulb holder
1
1. Screw
2. Tail/brake light lens
1 2
2RD-9-E0.book 32 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
1
2
3
4
56
7
8
9
10
11
12 3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screws. NOTICE: Do not over-
tighten the screws, otherwise
the lens may break.
[ECA10682] EAU60010
Replacing a turn
signal light
bulb1. Remove the turn signal light lens,
turn signal light rim and gasket by
removing the screws.
2. Remove the burnt-out bulb bypushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.
4. Install the gasket, rim and lens by installing the screws with the notch
on the rim and lens facing to in-
ward as shown. NOTICE: Do not
overtighten the screws, other-
wise the lens may break.
[ECA10682]
1. Tail/brake light bulb
1
1. Turn signal light lens
2. Screw
1
2
1. Turn signal light lens
2. Turn signal light rim
3. Gasket
3
2
1
2RD-9-E0.book 33 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-36
1
2
3
4
567
8
9
10
11
12
6. Pull the wheel axle out, and then
remove the collar and wheel.
NOTICE: Do not apply the brake
after the wheel and brake disc
have been removed, otherwise
the brake pads will be forced
shut.
[ECA11073]
To install the front wheel 1. Install the speedometer gear unit into the wheel hub so that the pro-
jections mesh with the slots.
2. Install the collar into the right side of the wheel hub.
3. Lift the wheel up between the fork legs.
TIPMake sure that there is enough space
between the brake pads before insert-
ing the brake disc and that the slot in
the speedometer gear unit fits over theretainer on the fork leg.
4. Insert the wheel axle from the left-hand side, and then install the
washer and axle nut.
5. Take the motorcycle off the center- stand so that the front wheel is on
the ground, and then put the side-
stand down.
6. Tighten the axle nut and the wheel axle holder nuts to their specified
torques
7. While applying the front brake, push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
8. Connect the speedometer cable.
1. Slot
2. Speedometer gear unit
3. Projection
2
3
1
1. Retainer
2. Slot
1
2
Tightening torques:
Axle nut:104 Nm (10.4 m·kgf, 74 ft·lbf)
Wheel axle holder nut: 9 Nm (0.9 m·kgf, 6.5 ft·lbf)
2RD-9-E0.book 36 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
1
2
3
4
56
7
8
9
10
11
12
EAU25081
Rear wheel
EAU59611
To remove the rear wheel
WARNING
EWA10822
To avoid injury, securely support the
vehicle so there is no danger of itfalling over. 1. Loosen the axle nut and the brake torque rod nut at the brake shoe
plate.
2. Disconnect the brake torque rod from the brake shoe plate by re-
moving the nut, washer and the
bolt.
3. Place the motorcycle on the cen-terstand.
4. Remove the brake pedal free play adjusting nut, and then disconnect
the brake rod from the brake cam-
shaft lever.
5. Loosen the drive chain puller lock- nut and the drive chain slack ad-
justing bolt on both ends of the swingarm.
6. Remove the axle nut and washer.
7. While supporting the rear wheel, pull the wheel axle out.
8. Remove the chain puller assem- blies and the spacer.
1. Brake rod
2. Brake camshaft lever
3. Brake pedal free play adjusting nut
4. Drive chain slack adjusting bolt
5. Drive chain puller locknut
6. Drive chain puller
7. Washer
8. Axle nut
9. Brake torque rod nut
10.Brake torque rod1 10
34
5
6
7
8
9
7
2
1. Drive chain slack adjusting bolt
2. Drive chain puller locknut
3. Axle nut
4. Washer
3
2
1
4
2RD-9-E0.book 37 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
1
2
3
4
567
8
9
10
11
12
9. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
TIPThe drive chain does not need to be
disassembled in order to remove andinstall the wheel.
To install the rear wheel1. Install the spacer into left side of the wheel hub.
2. Install the chain pullers and the wheel by inserting the wheel axle
from the left-hand side.
3. Install the drive chain onto the rear sprocket. 4. Install the washer and axle nut.
5. Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.
6. Connect the brake torque rod to the brake shoe plate by installing
the bolt, washer and nut.
7. Adjust the drive chain slack. (See page 6-22.)
8. Take the motorcycle off the center- stand so that the rear wheel is on
the ground, and then put the side-
stand down.
9. Tighten the brake torque rod nut and axle nut to the specified
torques.
10. Adjust the brake pedal free play. (See page 6-18.)
WARNING
EWA10661
After adjusting the brake pedal free
play, check the operation of the
brake light.
1. Drive chain
1
Tightening torques:Brake torque rod nut:19 Nm (1.9 m·kgf, 14 ft·lbf)
Axle nut: 129 Nm (12.9 m·kgf, 92 ft·lbf)
2RD-9-E0.book 38 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

MOTORCYCLE CARE AND STORAGE
7-2
1
2
3
4
5
678
9
10
11
12
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield. Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.TIPSalt sprayed on roads in the winter may
remain well into spring. 1. Clean the motorcycle with cold wa- ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10792]
2. Apply a corrosion protection spray on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
2RD-9-E0.book 2 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

MOTORCYCLE CARE AND STORAGE
7-3
1
2
3
4
5
67
8
9
10
11
12 including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar-
ingly and make sure to wipe off any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
EAU43203
StorageShort-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the motor-
cycle.NOTICE
ECA10811

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2RD-9-E0.book 3 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

SPECIFICATIONS
8-2
1
2
3
4
5
6
789
10
11
12
4th: 0.917 (22/24)
5th:
0.778 (21/27)
Chassis:Frame type: Semi double cradle
Caster angle:
27.70 
Trail: 111 mm (4.4 in)Front tire:Type:
With tube
Size: 90/100-18M/C 54S
Manufacturer/model: METZELER/ME77 FrontRear tire:Type:With tube
Size: 110/90-18M/C 61S
Manufacturer/model:
METZELER/ME77
Maximum load: 150 kg (331 lb)
* (Total weight of rider, passenger, cargo and accessories)Tire air pressure (measured on cold
tires):Loading condition:0–90 kg (0–198 lb) Front:
175 kPa (1.75 kgf/cm
2, 25 psi)
Rear:
200 kPa (2.00 kgf/cm2, 29 psi)
Loading condition: 90–150 kg (198–331 lb)
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
225 kPa (2.25 kgf/cm2, 33 psi)
Front wheel:Wheel type: Spoke wheel
Rim size:
18x1.85Rear wheel:Wheel type:Spoke wheel
Rim size:
18x2.15Front brake:Type:Single disc brake
Operation:
Right hand operation
Specified brake fluid: DOT 4Rear brake:Type:
Drum brake
Operation: Right foot operation
Front suspension:Type:
Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel: 150 mm (5.9 in)Rear suspension:Type:Swingarm
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
105 mm (4.1 in)Electrical system:Ignition system:TCI
Charging system:
AC magnetoBattery:Model:GT4B-5
Voltage, capacity:
12 V, 2.5 AhHeadlight:Bulb type:Halogen bulbBulb voltage, wattage  quantity:Headlight:
12 V, 60.0 W/55.0 W  1
Tail/brake light: 12 V, 5.0 W/21.0 W  1
Front turn signal light:
12 V, 21.0 W  2
2RD-9-E0.book 2 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

10-1
1
2
3
4
5
6
7
8
91011
12
INDEX
AAir filter element, replacing ...................... 6-12
Auxiliary light bulb, replacing ................... 6-34BBattery ..................................................... 6-28
Brake and clutch levers, checking and lubricating .............................................. 6-25
Brake fluid, changing ............................... 6-21
Brake fluid level, checking ....................... 6-20
Brake lever ................................................ 3-6
Brake lever free play, adjusting ............... 6-17
Brake light switches ................................. 6-19
Brake pads and shoes, checking............. 6-20
Brake pedal ............................................... 3-6
Brake pedal, checking and lubricating ..... 6-25
Brake pedal height and free play, adjusting ................................................ 6-18CCables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converter ..................................... 3-9
Centerstand and sidestand, checking and lubricating ....................................... 6-26
Clutch lever................................................ 3-5
Clutch lever free play, adjusting .............. 6-16DDecompression lever ............................... 3-11
Dimmer switch ........................................... 3-4
Drive chain, cleaning and lubricating ....... 6-23
Drive chain slack ..................................... 6-22EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-13
Engine oil and oil filter element.................. 6-9 Engine serial number ................................ 9-1
Engine stop switch .................................... 3-5
Engine trouble warning light ...................... 3-3
FFront fork, checking................................. 6-27
Fuel ........................................................... 3-7
Fuel cock ................................................. 3-10
Fuel consumption, tips for reducing .......... 5-3
Fuel level warning light .............................. 3-3
Fuel tank breather/overflow hose .............. 3-9
Fuel tank cap............................................. 3-7
Fuses, replacing ...................................... 6-29HHandlebar switches ................................... 3-4
Hazard switch............................................ 3-5
Headlight bulb, replacing......................... 6-31
High beam indicator light ........................... 3-3
Horn switch ............................................... 3-5IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-13
Indicator lights and warning lights ............. 3-2KKickstarter ............................................... 3-10MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-4
Maintenance, emission control system ..... 6-3
Matte color, caution ................................... 7-1
Model label ................................................ 9-2NNeutral indicator light ................................ 3-2PPanel, removing and installing .................. 6-7 Parking.......................................................5-4
Part locations .............................................2-1
Pass switch ................................................3-4
SSafety information ......................................1-1
Seat ......................................................... 3-11
Shifting .......................................................5-2
Shift pedal ..................................................3-6
Shift pedal, checking................................ 6-19
Shock absorber assemblies, adjusting ....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-8
Specifications.............................................8-1
Speedometer unit ......................................3-3
Starting the engine.....................................5-1
Starting the engine, trouble........................5-2
Steering, checking ................................... 6-27
Storage ......................................................7-3
Swingarm pivots, lubricating .................... 6-26TTachometer................................................3-4
Tail/brake light bulb, replacing ................. 6-32
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking............... 6-13
Tires ......................................................... 6-14
Tool kit .......................................................6-2
Troubleshooting ....................................... 6-39
Troubleshooting chart ..............................6-40
Turn signal indicator light ...........................3-2
Turn signal light bul b, replacing ............... 6-33
Turn signal switch ......................................3-4VValve clearance ....................................... 6-13
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分