seats YAMAHA SVHO CRUISER 2011 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2011, Model line: SVHO CRUISER, Model: YAMAHA SVHO CRUISER 2011Pages: 112, PDF Size: 7.79 MB
Page 95 of 112
Maintenance
89
EJU33768
Maintenance
Periodic checks and lubrication will keep your
watercraft in the safest and most efficient con-
dition possible. Therefore, make sure to carry
out the periodic maintenance. Safety is an ob-
ligation of the watercraft owner. Proper main-
tenance must be carried out to keep the
exhaust emission and sound levels within the
regulated limits. The most important points of
watercraft inspection and lubrication are ex-
plained on the following pages.
See a Yamaha dealer for genuine Yamaha re-
placement parts and optional accessories de-
signed for your watercraft.
Remember, failures that are the result of the
installation of parts or accessories which are
not qualitatively equivalent to genuine
Yamaha parts are not covered by the limited
warranty.
Maintenance, replacement, or repair of the
emission control devices and system may
be performed by any marine SI engine re-
pair establishment or individual. Warranty
repair, however, must be performed at an
authorized Yamaha marine dealership.
WARNING
EWJ00311
Be sure to turn off the engine when you
perform maintenance unless otherwise
specified. If you are not familiar with ma-
chine servicing, this work should be done
by a Yamaha dealer or other qualified me-
chanic.
EJU33802Tool kit
A tool kit is included with this watercraft. Place
the tool kit in a waterproof bag and alwayscarry it with you whenever you use the water-
craft.
EJU40432Removing and installing the engine
cover
The engine cover is removable.
To remove the engine cover:
(1) Remove the seats. (See page 47 for seat
removal and installation procedures.)
(2) Remove the engine cover screws.
1Tool bag
2Screwdriver
3Garden hose adapter
410/12 mm box wrench
5Pliers
6Open-end wrench
1Engine cover screw
1
UF1W73E0.book Page 89 Monday, June 7, 2010 9:17 AM
Page 96 of 112
Maintenance
90
(3) Slide the engine cover toward the stern,
and then lift up the cover to remove it.
To install the engine cover:
(1) Place the engine cover in its original posi-
tion, push it down, and then slide it toward
the bow.
(2) Install the engine cover screws, and then
tighten them to the specified torque.
(3) Securely install the seats in their original
positions.
1Engine cover
Tightening torque:
Engine cover screw:
4.5 Nm (0.46 kgf-m, 3.3 ft-lb)
1
UF1W73E0.book Page 90 Monday, June 7, 2010 9:17 AM
Page 104 of 112
Trouble recovery
98
(2) Remove any weeds or debris from
around the jet intake, drive shaft, impel-
ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.
EJU34641Jumping the battery
If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.
EJU34663Connecting the jumper cables
WARNING
EWJ01250
To avoid battery explosion and serious
damage to the electrical system:
Do not reverse the polarity of the jumper
cables when connecting to the batteries.
Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.
Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.
(1) Connect the positive (+) jumper cable to
the positive (+) battery terminals of both
batteries.
(2) Connect one end of the negative (–)
jumper cable to the negative (–) battery
terminal of the booster battery.(3) Connect the other end of the negative (–)
jumper cable to an engine hanger.
(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above. (See page 28 for information on
starting the engine.)
EJU36994Replacing the fuses
If a fuse is blown, replace it with the proper
fuse.
To replace a fuse:
(1) Remove the seats. (See page 47 for seat
removal and installation procedures.)
1Negative (–) jumper cable
2Positive (+) jumper cable
3Booster battery
4Engine hanger
1Good fuse
2Blown fuse
12
3
4
2 1
UF1W73E0.book Page 98 Monday, June 7, 2010 9:17 AM
Page 106 of 112
Trouble recovery
100
(7) Securely install the seats in their original
positions.
If the fuse immediately blows again, the elec-
trical system may be defective. If this occurs,
have a Yamaha dealer service the watercraft.
EJU41820Replacing the bilge pump fuse
If the fuse is blown, replace it with the proper
fuse.
To replace the fuse:
(1) Remove the seats and engine cover.
(See page 47 for seat removal and instal-
lation procedures and page 89 for engine
cover removal and installation proce-
dures.)
(2) Remove the plastic ties that are securing
the corrugated tube and bilge pump fuse
leads.
TIP:
Be careful not to drop the plastic ties into the
engine compartment.
(3) Pull out the bilge pump fuse holder from
the rubber cover, and then remove the
fuse cover.
(4) Replace the blown fuse with the spare
fuse of the correct amperage.
WARNING! Do not use fuses of a dif-
ferent amperage than recommended.
Substitution with a fuse that has an
improper rating can cause extensive
electrical system damage and possi-
ble fire.
[EWJ00802]
TIP:
If the fuse is difficult to remove, use the fuse
puller on the reverse side of the electrical box
1Good fuse
2Blown fuse
2 1
1Bilge pump fuse lead
2Plastic tie
3Corrugated tube
213
UF1W73E0.book Page 100 Monday, June 7, 2010 9:17 AM
Page 107 of 112
Trouble recovery
101
cap. (See page 98 for information on the fuse
puller.)
(5) Securely install the fuse cover, and then
fit the bilge pump fuse holder into the rub-
ber cover.
(6) Secure the bilge pump fuse leads and
corrugated tube with the plastic ties.
(7) Securely install the engine cover and
seats in their original positions.If the fuse immediately blows again, the elec-
trical system may be defective. If this occurs,
have a Yamaha dealer service the watercraft.
EJU34715Towing the watercraft
WARNING
EWJ00811
The operator of the towing boat must
keep speed to a minimum and avoid traf-
fic or obstacles which could be a hazard
to the operator on the watercraft.
The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down.
If the watercraft becomes inoperative in the
water, it can be towed to shore.
To tow the watercraft:
Use a towline that is three times the combined
length of the towing boat and the watercraft.
(1) Securely attach the towline to the bow
eye of the watercraft being towed.
(2) Sit astride the seat and hold on to the
handlebars in order to balance the water-
craft. NOTICE: The bow must be kept
up out of the water during towing, oth-
erwise water could flood the engine
compartment or water could flow back
into the engine, causing severe en-
gine damage.
[ECJ01330]
1Bilge pump fuse holder
2Fuse cover
3Spare fuse
4Fuse
Fuse amperage:
Bilge pump fuse:
3 A
1Bilge pump fuse lead
2Plastic tie
3Corrugated tube
4Rubber cover
21
43
213
4
1Bow eye
UF1W73E0.book Page 101 Monday, June 7, 2010 9:17 AM
Page 110 of 112
Index
Leaving the watercraft .............................. 73
Limitations on who may operate
the watercraft ........................................ 10
Long-term storage .................................... 87
Low RPM Mode........................................ 34
Lubrication................................................ 87
M
Main components, location of .................. 22
Maintenance............................................. 89
Model information....................................... 2
Multifunction display (FX Cruiser SHO) ... 44
Multifunction information center ............... 39
Multifunction information center check ..... 70
N
No-wake mode ......................................... 35
O
Oil pressure warning ................................ 43
Operating in weeded areas ...................... 82
Operating the watercraft........................... 73
Operating the watercraft in reverse .......... 76
Operating your watercraft......................... 71
Operation requirements ........................... 12
P
Periodic maintenance chart...................... 91
Post-launch checks .................................. 69
Post-operation care .................................. 83
Pre-launch checks.................................... 63
Pre-operation check points ...................... 63
Pre-operation checklist............................. 61
Primary Identification (PRI-ID) number ...... 1
Pull-up cleats (FX Cruiser SHO) .............. 50
Q
Quick Shift Trim System (Q.S.T.S.) ......... 33
Quick Shift Trim System (Q.S.T.S.)
checks................................................... 66
R
Reboarding step ....................................... 48
Recommended equipment ....................... 14
Remote control transmitter ....................... 26
Remote control transmitter check ............ 67
Reverse system ....................................... 32
Reverse system checks ........................... 66
Riding position.......................................... 72
Rustproofing ............................................. 88S
Safe boating rules .................................... 19
Safety equipment check ........................... 69
Seat storage compartment ....................... 52
Seats ........................................................ 47
Start switch............................................... 28
Starting off ................................................ 79
Starting off from a trailer ........................... 80
Starting the engine on water .................... 72
Steering system ....................................... 29
Steering system checks ........................... 65
Stern drain plug checks ............................ 69
Stern eyes ................................................ 49
Stopping the engine ................................. 73
Stopping the watercraft ............................ 75
Storage compartment checks .................. 68
Storage compartments ............................. 50
Submerged watercraft ............................ 102
Switch checks .......................................... 68
T
Throttle lever ............................................ 29
Throttle lever checks ................................ 67
Tool kit...................................................... 89
Towing the watercraft ............................. 101
Transporting on a trailer ........................... 59
Troubleshooting ....................................... 94
Troubleshooting chart .............................. 94
Turning the watercraft .............................. 74
W
Water separator ....................................... 31
Water separator check ............................. 63
Watercraft characteristics ......................... 15
Watercraft control functions ..................... 26
Watercraft operation functions ................. 32
Watercraft operation modes ..................... 34
Water-skiing ............................................. 17
Watertight storage compartment .............. 53
Y
Yamaha Security System ......................... 27
Yamaha Security System settings ........... 27
UF1W73E0.book Page 2 Monday, June 7, 2010 9:17 AM