lights YAMAHA T135 2006 User Guide

MOTORCYCLE CARE AND STORAGE
7-1
7
EAU26000
Care While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly in-
stalled.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.
Cleaning
CAUTION:
ECA10770


Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.


Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge
with mild detergent and water to
clean plastic.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasivecleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound afterwashing.
U5YPE0E0.book Page 1 Wednesday, February 23, 2005 4:22 PM

INDEXAAir filter element, cleaning..................... 6-13BBattery................................................... 6-28
Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-21
Brake lever .............................................. 3-4
Brake lever free play, checking ............. 6-19
Brake lever, lubricating ......................... 6-25
Brake pads and shoes, checking .......... 6-20
Brake pedal ............................................. 3-5
Brake pedal free play, adjusting............ 6-19
Brake pedal, lubricating ........................ 6-25CCables, checking and lubricating .......... 6-24
Carburetor, adjusting ............................ 6-14
Care ........................................................ 7-1
Catalytic converter .................................. 3-6
Centerstand and sidestand,
checking and lubricating ..................... 6-25
Coolant.................................................. 6-11
Coolant temperature warning light .......... 3-2
Cowlings and panel, removing and
installing................................................ 6-5DDimmer switch ........................................ 3-4
Drive chain, cleaning and lubricating .... 6-23
Drive chain slack ................................... 6-22EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-15
Engine oil and oil filter element ............... 6-9
Engine serial number .............................. 9-2
Engine, starting a warm .......................... 5-2
FFront fork, checking .............................. 6-26
Fuel......................................................... 3-6
Fuel consumption, tips for reducing........ 5-3
Fuel gauge.............................................. 3-3
Fuel tank cap .......................................... 3-5
Fuse, replacing ..................................... 6-29GGear position indicator lights .................. 3-2
General note ........................................... 5-6HHandlebar switches ................................ 3-3
Headlight bulb, replacing ...................... 6-30
Helmet holders ....................................... 3-8
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-4IIdentification numbers ............................ 9-1
Indicator and warning lights .................... 3-2KKey identification number ....................... 9-1
Kickstarter............................................... 3-7MMain switch/steering lock........................ 3-1NNeutral indicator light .............................. 3-2PParking ................................................... 5-5
Part locations .......................................... 2-1
Periodic maintenance and
lubrication chart .................................... 6-2
Pre-operation check list .......................... 4-2RRear brake light switch, adjusting ......... 6-20Rear turn signal light and
tail/brake light...................................... 6-31
SSafety information ................................... 1-1
Seat ......................................................... 3-7
Shifting .................................................... 5-2
Shift pedal ............................................... 3-4
Sidestand ................................................ 3-9
Spark plug, checking ............................... 6-7
Specifications .......................................... 8-1
Speedometer unit .................................... 3-3
Starter (choke) lever................................ 3-7
Starting and warming up a
cold engine ........................................... 5-1
Start switch.............................................. 3-4
Steering, checking................................. 6-27
Storage.................................................... 7-3
Storage compartment.............................. 3-8
Swingarm pivots, lubricating ................. 6-26TThrottle cable free play, adjusting ......... 6-15
Throttle grip and cable, checking and
lubricating ........................................... 6-24
Tires ...................................................... 6-16
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-35
Troubleshooting charts.......................... 6-36
Turn signal indicator light ........................ 3-2
Turn signal light bulb (front) or
auxiliary light bulb, replacing............... 6-31
Turn signal switch ................................... 3-4VValve clearance..................................... 6-16
Vehicle identification number .................. 9-1
U5YPE0E0.book Page 1 Wednesday, February 23, 2005 4:22 PM