light YAMAHA TMAX 2003 Owner's Manual

6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EW000119
w
Headlight bulbs get very hot.
Therefore, keep flammable prod-
ucts away from a lit headlight bulb,
and do not touch the bulb until it
has cooled down.
3. Place a new bulb into position,
and then secure it with the bulb
holder.
a
a. Do not touch the glass part of the bulb.
EAU03087
TroubleshootingTroubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition sys-
tems, for example, can cause poor
starting and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter
require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools,
experience, and know-how to service
the scooter properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills.
EC000105
cC
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be
adversely affected. Thoroughly
clean off any dirt and fingerprints
on the headlight bulb using a cloth
moistened with alcohol or thinner.
4. Install the bulb cover, and then
connect the coupler.
5. Have a Yamaha dealer adjust
the headlight beam if necessary.
5GJ-28199-E2 9/9/02 9:15 AM Page 79

7-2
SCOOTER CARE AND STORAGE
7 8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8 8
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roads
Since sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA00012
cC
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
5GJ-28199-E2 9/9/02 9:15 AM Page 85

8-3
SPECIFICATIONS
8
Wheels
Front
Type Cast wheel
Size 14 M/C ×MT3.50
Rear
Type Cast wheel
Size 14 M/C ×MT4.50
Brakes
Front
Type Single disc brake
Operation Right hand
Fluid DOT 4
Rear
Type Single disc brake
Operation Left hand
Fluid DOT 4Suspension
Front Telescopic fork
Rear Swingarm
Spring/shock absorbers
Front Coil spring/oil damper
Rear Coil spring/gas-oil damper
Wheel travel
Front 120 mm
Rear 120 mm
Electrical
Ignition system Transistorized coil ignition
(digital)
Charging system
Type A.C. magneto
Standard output 14 V, 310W @ 5,000 r/min
Battery
Type GT9B-4
Voltage, capacity 12 V, 8 Ah
Headlight bulb typeHalogen
Bulb voltage, wattage ×quantity
Headlight 12 V, 60/55 W ×1
12 V, 55 W ×1
5GJ-28199-E2 9/9/02 9:15 AM Page 92

8-4
SPECIFICATIONS
8
Tail/brake light 12 V, 5/21 W ×2
Front turn signal light 12 V, 5/21 W ×2
Rear turn signal light 12 V, 21 W ×2
Auxiliary light 12 V, 5 W ×2
License plate light 12 V, 5 W ×1
Meter lighting 12 V, 1.7 W ×3
High beam indicator light 12 V, 1.7 W ×1
Oil change indicator light 12 V, 1.7 W ×1
Turn indicator light 12 V, 3.4 W ×2
V-belt replacement
indicator light 12 V, 1.7 W ×1
Fuses
Main fuse 30 A
Signaling system fuse 15 A
Headlight fuse 15 A
Ignition fuse 10 A
Radiator fan fuse 15 A
Hazard fuse 10 A
Clock fuse (backup fuse) 10 A
5GJ-28199-E2 9/9/02 9:15 AM Page 93

INDEX
F
Front and rear brake levers ..................6-25
Front and rear brake pads, checking ....6-26
Front fork, checking ..............................6-30
Fuel ......................................................3-10
Fuel consumption, tips for reducing .......5-3
Fuel gauge .............................................3-4
Fuel tank cap ..........................................3-9
Fuses, replacing ...................................6-34
H
Handlebar switches ................................3-6
Dimmer switch .....................................3-6
Engine stop switch ...............................3-7
Hazard switch ......................................3-7
Horn switch ..........................................3-7
Pass switch ..........................................3-6
Start switch ..........................................3-7
Turn signal switch ................................3-7
Headlight bulb, replacing ......................6-35
Headlight variations ................................3-8
Helmet holder .......................................3-13
I
Identification numbers ............................9-1
Ignition circuit cut-off system ................3-15
Indicator lights ........................................3-2
High beam indicator light .....................3-3
Oil change indicator light .....................3-2
Turn signal indicator lights ...................3-3
V-belt replacement indicator light ........3-3K
Key identification number .......................9-1
M
Main switch/steering lock .......................3-1
Model label .............................................9-2
P
Parking ...................................................5-4
Part locations ..........................................2-1
Periodic maintenance and lubrication
chart .....................................................6-3
Pre-operation check list ..........................4-1
R
Rider backrest, adjusting ......................3-12
S
Safe-riding points ...................................1-2
Seat ......................................................3-11
Self-diagnosis device .............................3-6
Sidestand .............................................3-14
Spark plugs, checking ............................6-9
Specifications .........................................8-1
Speedometer unit ...................................3-4
Starting off ..............................................5-2
Starting the engine .................................5-1
Steering, checking ................................6-31
Storage ...................................................7-4
Storage compartments .........................3-14A
Acceleration and deceleration ................5-2
Air filter element, cleaning ....................6-19
Anti-theft alarm (optional) .......................3-6
B
Battery ..................................................6-32
Brake fluid level, checking ....................6-27
Brake fluid, changing ............................6-28
Brake lever, front ....................................3-9
Brake lever, rear .....................................3-9
Brake levers, lubricating .......................6-29
Braking ...................................................5-3
C
Carburetors, adjusting ..........................6-21
Care ........................................................7-1
Centerstand and sidestand, checking and
lubricating ..........................................6-29
Chain drive oil .......................................6-15
Clock ......................................................3-5
Conversion table ....................................8-5
Coolant ..................................................6-17
Coolant temperature gauge ....................3-5
Cowlings and panels, removing and
installing ...............................................6-6
E
Engine break-in ......................................5-4
Engine idling speed ..............................6-21
Engine oil and oil filter cartridge ...........6-12
5GJ-28199-E2 9/9/02 9:15 AM Page 98