stop start YAMAHA TT-R110E 2015 Owners Manual

DESCRIPTION
3-1
3
EAU10411
Left view
678
123 4
5
1. Fuel cock (page 4-6)
2. Starter (choke) lever (page 4-7)
3. Fuse (page 7-28)
4. Battery (page 7-26)
5. Clutch adjusting screw (page 7-17)
6. Engine oil drain bolt (page 7-9)
7. Shift pedal (page 4-2)
8. Throttle stop screw (page 7-14)
UB5180E0.book Page 1 Monday, June 9, 2014 1:20 PM

DESCRIPTION
3-3
3
EAU10431
Controls and instruments
123 4
5
1. Engine stop switch (page 4-1)
2. Main switch (page 4-1)
3. Start switch (page 4-1)
4. Brake lever (page 4-2)
5. Throttle grip (page 7-15)
UB5180E0.book Page 3 Monday, June 9, 2014 1:20 PM

INSTRUMENT AND CONTROL FUNCTIONS
4-1
4
EAU40341
Main switchThe main switch controls the ignition
system. The main switch positions are
described below.
EAU10631
ON
All electrical systems are supplied with
power, and the engine can be started.
The key cannot be removed.
EAU45752
OFF
All electrical systems are off. The key
can be removed.
WARNING
EWA10073
Never turn the key to “OFF” while
the vehicle is moving, otherwise the
electrical systems will be switched
off, which may result in loss of con-
trol or an acci dent.
EAU1234H
Han dle bar switchesLeft
Ri ght 1. Engine stop switch “ / ”
1. Start switch “ ”
1
UB5180E0.book Page 1 Monday, June 9, 2014 1:20 PM

INSTRUMENT AND CONTROL FUNCTIONS
4-2
4
EAU12661
Engine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12713
Start switch “ ”
Push this switch to crank the engine
with the starter. See page 6-1 for start-
ing instructions prior to starting the en-
gine.
EAU39852
Shift pe dalThis motorcycle is equipped with a
constant-mesh 4-speed transmission.
The shift pedal is located on the left
side of the motorcycle. Neutral is at the
bottom position.
EAU12892
Brake leverThe brake lever is located on the right
side of the handlebar. To apply the
front brake, pull the lever toward the
throttle grip.
1. Shift pedal
1
1. Brake lever
1
UB5180E0.book Page 2 Monday, June 9, 2014 1:20 PM

INSTRUMENT AND CONTROL FUNCTIONS
4-10
4
With the engine turned off:
1. Make sure that the engine stop switch is set to “”.
2. Turn the key to “ON”.
3. Shift the transmission into gear.
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
The neutral switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
6. Shift the transmission into the neutral position.
7. Push the start switch.
Does the engine start?
The neutral switch may not be working correctly.
The motorcycle should not be ridden
until
checked by a Yamaha dealer.
YES
NO
The system is OK. The motorcycle can be ridden.
YES
NO
If a malfunction is noted, have a Yamaha
dealer check the system before riding.
WARNING
UB5180E0.book Page 10 Monday, June 9, 2014 1:20 PM

OPERATION AND IMPORTANT RIDING POINTS
6-1
6
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which coul d cause an acci dent
or injury.
EAU44815
Startin g an d warmin g up a
col d en gine1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
3. Shift the transmission into the neutral position.
WARNING
EWA14411
Be sure to shift the transmission
into neutral b efore starting the
en gine.
 Never ri de with the si destan d
d own.4. Turn the starter (choke) on and
completely close the throttle. (See
page 4-7.)
5. Start the engine by pushing the start switch or by pushing the
kickstarter lever down.
6. When the engine is warm, turn the starter (choke) off.
TIPThe engine is warm when it responds
quickly to the throttle with the starter
(choke) turned off.NOTICE
ECA11043
For maximum en gine life, never ac-
celerate har d when the en gine is
col d!
UB5180E0.book Page 1 Monday, June 9, 2014 1:20 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
7-14
7
EAU39931
Adjustin g the car buretorThe carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most
carburetor adjustments should be left
to a Yamaha dealer, who has the nec-
essary professional knowledge and ex-
perience. The adjustment described in
the following section, however, may be
serviced by the owner as part of rou-
tine maintenance.NOTICE
ECA10551
The car buretor has b een set and ex-
tensively teste d at the Yamaha fac-
tory. Chan gin g these settin gs
without sufficient technical knowl-
e dge may result in poor perfor-
mance of or damag e to the en gine.
EAU21363
A djustin g the en gine i dlin g
spee dThe engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.TIPA diagnostic tachometer is needed to
make this adjustment.1. Attach the tachometer to the
spark plug lead.
2. Start the engine and warm it up for several minutes at 1000–2000
r/min while occasionally revving it
to 4000–5000 r/min.TIPThe engine is warm when it quickly re-
sponds to the throttle.3. Check the engine idling speedand, if necessary, adjust it to
specification by turning the throt-
tle stop screw. To increase the en-
gine idling speed, turn the screw in direction (a). To decrease the en-
gine idling speed, turn the screw in
direction (b).
TIPIf the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.1. Throttle stop screw
En
gine i dlin g spee d:
1600–1800 r/min
(a) (b)1
UB5180E0.book Page 14 Monday, June 9, 2014 1:20 PM

11-1
11
INDEX
AAir filter element, cleaning .................... 7-11BBattery .................................................. 7-26
Brake lever.............................................. 4-2
Brake lever, checking and lubricating........................................... 7-23
Brake lever free play, adjusting ............ 7-18
Brake pedal ............................................ 4-3
Brake pedal, checking and lubricating........................................... 7-24
Brake pedal free play, adjusting ........... 7-19
Brake shoes, checking ......................... 7-20CCables, checking and lubricating ......... 7-23
Carburetor, adjusting............................ 7-14
Care ........................................................ 8-1
Clutch free play, adjusting .................... 7-17DDrive chain, cleaning and lubricating ... 7-22
Drive chain slack .................................. 7-21EEngine break-in ...................................... 6-3
Engine idling speed .............................. 7-14
Engine oil ................................................ 7-9
Engine serial number ............................ 10-1
Engine, starting a warm.......................... 6-2
Engine stop switch ................................. 4-2FFront fork, checking ............................. 7-25
Fuel ......................................................... 4-3
Fuel cock ................................................ 4-6
Fuel tank breather hose.......................... 4-6
Fuel tank cap .......................................... 4-3 Fuse, replacing..................................... 7-28
HHandlebar switches ............................... 4-1IIdentification numbers ......................... 10-1KKickstarter .............................................. 4-7LLabels, location ...................................... 1-1MMain switch ............................................ 4-1
Maintenance and lubrication, periodic... 7-4
Maintenance, emission control
system ................................................. 7-3
Matte color, caution ............................... 8-1
Model label........................................... 10-1PPanels, removing and installing ............. 7-7
Parking ................................................... 6-4
Part locations ......................................... 3-1SSafety information .................................. 2-1
Seat ........................................................ 4-8
Shifting ................................................... 6-2
Shift pedal .............................................. 4-2
Shift pedal, checking ........................... 7-20
Shock absorber assembly ..................... 4-8
Sidestand ............................................... 4-9
Sidestand, checking and lubricating.... 7-24
Spark arrester, cleaning ....................... 7-13
Spark plug, checking ............................. 7-8
Specifications......................................... 9-1
Starter (choke) lever ............................... 4-7 Starting and warming up a cold
engine ................................................... 6-1
Starting circuit cut-off system ................ 4-9
Start switch ............................................. 4-2
Steering, checking ................................ 7-25
Storage ................................................... 8-3
Supporting the motorcycle ................... 7-28
Swingarm pivots, lubricating ................ 7-24
TThrottle grip and cable, checking and lubricating ........................................... 7-23
Throttle grip free play, checking ........... 7-15
Tires ...................................................... 7-15
Tool kit .................................................... 7-2
Troubleshooting .................................... 7-32
Troubleshooting chart........................... 7-34VValve clearance..................................... 7-15
Vehicle Emission Control Information label (For Canada) .............................. 10-2
Vehicle identification number ............... 10-1WWheel bearings, checking .................... 7-26
Wheel (front).......................................... 7-29
Wheel (rear)........................................... 7-31
Wheels .................................................. 7-17
UB5180E0.book Page 1 Monday, June 9, 2014 1:20 PM