air filter YAMAHA TT600RE 2004 Service Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: TT600RE, Model: YAMAHA TT600RE 2004Pages: 382, PDF Size: 6.39 MB
Page 22 of 382
SPECGENERAL SPECIFICATIONS
2-1
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item Standard Limit
ModelTT600RE: 5CH5
Dimensions
Overall length 2,220 mm •••
Overall width 865 mm •••
Overall height 1,195 mm •••
Seat height 890 mm •••
Wheelbase 1,480 mm •••
Ground clearance 280 mm •••
Minimum turning radius 3,300 mm (right)
3,100 mm (left) •••
Basic weight (with oil and full
fuel tank)164.5 kg •••
Engine
Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined single cylinder
Displacement 595 cm
3•••
Bore x stroke 95.0 x 84.0 mm •••
Compression ratio 8.5 : 1 •••
Starting system Electric starter
Lubrication system Dry sump with separate oil tank
Engine oil
Type
Temp. °CSAE20W40SE or SAE10W30SE •••
Recommended engine oil classification API Service SE, SF, SG or higher •••
Quantity:
Without oil filter cartridge
replacement 2.4 L •••
With oil filter cartridge
replacement 2.5 L •••
Total amount (dry engine) 3.0 L •••
Air filterWet type element
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 10 L •••
Fuel reserve amount 3.0 L •••
Carburetor
Manufacturer TEIKEI
Model x quantity Y30PV-2ATK x 1
ProCarManuals.com
Page 29 of 382
SPECMAINTENANCE SPECIFICATIONS
2-8
Item Standard Limit
Ballancer
Ballancer drive method Gear
Clutch
Clutch release method Inner push, cam push
Friction plate thickness 2.72 - 2.88 mm •••
Wear limit ••• 2.60 mm
Plate quantity 6 pcs
Friction plate thickness 2.94 - 3.06 mm •••
Wear limit ••• 2.8 mm
Plate quantity 2 pcs
Clutch plate thickness 1.20 mm •••
Plate quantity 7 pcs
Max. warpage ••• 0.20 mm
Clutch spring free length 42.8 mm •••
Plate quantity 5 pcs
Clutch housing thrust clearance 0.070 - 0.071 mm •••
Transmission
Max. main axle runout ••• 0.08 mm
Max. drive axle runout ••• 0.08 mm
Shift mechanism type Cam drum and guide bar
Carburetor
ID mark 5CH5 10
Main jet #1:#150 #2:#145
Main air jet #1:1.0 #2:0.9
Jet needle #1:5C5A-3/5 #2:5Y18-3/5
Needle jet 2.600
Cutaway 4.00
Pilot air jet 1 # 0.8 mm
Pilot jet # 50
Bypass 1 # 1.0
Pilot screw turns out 2-3/4 +/- 1/2
Valve seat size 2.5
Starter jet 1 # 74
Float height 6.0 - 8.0 mm •••
Engine idle speed1,150-1,450 r/min •••
CO% 1.5 - 3 •••
Intake vacuum 30.6-33.36 kPa - 230-250 mm Hg •••
Lubrication systemDry sump
Oil filter type Paper type
Oil pump:
Oil pump type Trochoid type
Inner rotor to outer rotor tip clearance 0.12 mm 0.20 mm
Outer rotor to pump housing
clearance 0.030 - 0.080 mm 0.150 mm
Bypass valve opening pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm
2) •••
Relief valve operating pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm2) •••
Oil pressure (hot) 13.0 kPa (0.13 kgf/cm2)/1,300 r/min •••
Pressure check location Oil filter chamber •••
ProCarManuals.com
Page 32 of 382
SPECMAINTENANCE SPECIFICATIONS
2-11
Tightening
Part torque
Part to be tightened
nameThread size Remarks
Nm mkg
Stator (pick-up coil) Hexagon socket
head screw M6 x 1.0 7 0.7
Engine oil pipe 1 Hexagon socket
head screw M6 x 1.0 10 1.0
Engine oil pipe 2 Union screw M12 x 1.25 35 3.5
Oil delivery pipe Union bolt M8 x 1.25 18 1.8
Carburetor joints Hexagon socket
head screw M6 x 1.0 10 1.0
Air filter case (frame) Hexagon screw M6 x 1.0 10 1.0
Air filter case (frame) Washer based
screw M6 x 1.0 10 1.0
Exhaust pipe Washer based
nut M6 x 1.0 10 1.0
Exhaust pipe protector Pan head (+)
screw M6 x 1.0 7 0.7
Muffler Hexagon socket
head screw M8 x 1.25 23 2.3
Muffler (band) Nut, nylon M8 x 1.25 23 2.3
Muffler Washer based
screw M8 x 1.25 23 2.3
Crankcase Hexagon socket
head screw M6 x 1.0 10 1.0
Crankcase Stud bolt M10 x 1.25 20 2.0
Crankcase cover (right) Hexagon socket
head screw M6 x 1.0 10 1.0
Crankcase cover (left) Hexagon socket
head screw M6 x 1.0 10 1.0
Sprocket cover Hexagon socket
head screw M6 x 1.0 10 1.0
Stop washer (bearing) Flat headscrew M6 x 1.0 7 0.7
Pressure plate Washer based
screw M6 x 1.0 8 0.8
Clutch housing Hexagon nut M20 x 1.0 90 9.0
Primary drive gear Hexagon nut M20 x 1.0 120 12.0
ProCarManuals.com
Page 35 of 382
SPECMAINTENANCE SPECIFICATIONS
2-14
Tightening
Part to be tightened Thread torque
Remarkssize
N·mm·kg
Engine mounting and rear frame:
Engine front/Stay engine M10 x 1.25 64 6.4
Stay engine (engine front)/Frame M10 x 1.25 64 6.4
Engine rear under/Frame M10 x 1.25 68 6.8
Engine top/Stay engine M10 x 1.25 64 6.4
Engine protector/Frame M6 x 1.0 7 0.7
Chain tensioner top/Frame M8 x 1.25 23 2.3
Chain tensioner under/Frame M8 x 1.25 23 2.3
Frame/Rear frame (upper) M8 x 1.25 23 2.3
Frame/Rear frame (under) M8 x 1.25 23 2.3
Rear frame/Air filter assy M6 x 1.0 5 0.5
Front fork and steering:
Handle crown/Inner tube M8 x 1.25 28 2.8
Handle crown/Steering shaft M28 x 1.5 4 0.4 See “NOTE”
Steering shaft/Ring nut M36 x 1.5 115 11.5
Holder handle upper/Crown handle M8 x 1.25 20 2.0
Holder handle under/Crown handle M10 x 1.5 40 4.0
Front fork under bracket/Inner tube M8 x 1.25 23 2.3
Front master cylinder/Cap M4 x 0.7 1.5 0.15
Front master cylinder/Handle M6 x 1.0 9 0.9
Union bolt tightening M10 x 1.0 20 2.0
Front fender/Front fork M6 x 1.0 7 0.7
Stay headlight/Handle crown M6 x 1.0 10 1.0
Stay headlight/Bracket meter M6 x 1.0 6 0.6
Headlight/Stay headlight M6 x 1.0 10 1.0
Rear arm and cushion:
Pivot shaft/Frame M14 x 1.5 90 9.0
Arm relay/Frame M10 x 1.25 60 6.0
Arm relay/Rod connecting M10 x 1.25 52 5.2
Arm relay/Shock absorber M10 x 1.25 59 5.9
Rod connecting/Rear arm M12 x 1.25 66 6.6
Shock absorber upper/Frame M12 x 1.25 66 6.6
Seal guard/Rear arm M6 x 1.0 4 0.4
Support chain/Rear arm M6 x 1.0 9 0.9
Chain case/Rear arm M6 x 1.0 9 0.9
Front wheel:
Front wheel shaft/Front fork M16 x 1.5 59 5.9
Axle holder//Front fork M6 x 1.0 9 0.9
Rear wheel:
Rear wheel shaft/Nut M18 x 1.5 115 11.5
Clutch hub/Sprocket M10 x 1.25 48 4.8
Tightening torques
ProCarManuals.com
Page 37 of 382
SPECMAINTENANCE SPECIFICATIONS
2-16
Tightening
Part to be tightened Thread torque
Remarkssize
N·mm·kg
Starting motor cord/Starting motor M6 x 1.0 11 1.1
Wire minus lead (-)/Starting motor M6 x 1.0 10 1.0
Front flasher lights/Stay, headlight M6 x 1.0 1.5 0.15
Clutch wire/Engine M6 x 1.0 7 0.7
Assist grip (Standing handle)/Rear frame M8 x 1.25 23 2.3
Speedometer M5 x 0.8 4 0.4
Air filter case 1/Air filter case 2 (L = 13 mm) M3.9 0.5 0.05
Air filter case 1/Air filter case 2 (L = 19 mm) M3.9 1 0.1
Hose clamp/Joint, carburator M4 x 0.7 0.6 0.06
Hose clamp/Air cleaner/Carburator M5 x 0.8 0.8 0.08
Battery (+)/(-) M6 x 1.0 2.5 0.25
NOTE:
1. First tighten the ring nut approximately 38 Nm (3.8 mkg) by using the torque wrench, then loosen the
ring nut one turn.
2. Final tighten the ring nut at the torque of 4 Nm (0.4 mkg).
ProCarManuals.com
Page 53 of 382
INSP
ADJ
CHAPTER 3.
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION..........................................................................................................3-1
PERIODIC MAINTENANCE/LUBRICATION INTERVALS........................................3-1
SEAT, FUEL TANK AND REAR COWLING................................................................3-3
REMOVAL ............................................................................................................3-3
INSTALLATION ....................................................................................................3-3
ENGINE........................................................................................................................3-4
VALVE CLEARANCE ADJUSTMENT ..................................................................3-4
DRIVE CHAIN ADJUSTMENT ..............................................................................3-7
IDLE SPEED ADJUSTMENT ................................................................................3-7
THROTTLE CABLE FREE PLAY ADJUSTMENT ................................................3-8
SPARK PLUG INSPECTION ................................................................................3-9
IGNITION TIMING CHECK ................................................................................3-11
COMPRESSION INSPECTION ..........................................................................3-12
ENGINE OIL LEVEL CHECK ..............................................................................3-15
ENGINE OIL REPLACEMENT ............................................................................3-17
ENGINE OIL PRESSURE CHECK ....................................................................3-21
CLUTCH ADJUSTMENT ....................................................................................3-21
AIR FILTER CLEANING ......................................................................................3-24
FUEL FILTER CLEANING ..................................................................................3-25
ENGINE OIL TANK FILTER CLEANING ............................................................3-26
SUCTION HOSE AND MANIFOLD INSPECTION..............................................3-28
FUEL LINE INSPECTION ..................................................................................3-28
CRANKCASE VENTILATION HOSE INSPECTION ..........................................3-29
EXHAUST SYSTEM INSPECTION ....................................................................3-29
CHASSIS....................................................................................................................3-30
ADJUSTING THE FRONT BRAKE ....................................................................3-30
ADJUSTING THE REAR BRAKE ......................................................................3-31
CHECKING THE BRAKE FLUID LEVEL ............................................................3-32
BRAKE PAD WEAR INSPECTION ....................................................................3-33
BRAKE HOSING INSPECTION ..........................................................................3-33
BRAKE CIRCUIT BLEEDING ............................................................................3-34
DRIVE CHAIN SLACK INSPECTION AND ADJUSTMENT..................................3-35
DRIVE CHAIN LUBRICATION ............................................................................3-36
FRONT FORK INSPECTION ..............................................................................3-37
ADJUSTING THE FRONT FORK ......................................................................3-37
REAR SHOCK ABSORBER ADJUSTMENT ......................................................3-38
STEERING INSPECTION ..................................................................................3-40
TYRE INSPECTION ............................................................................................3-41
WHEEL INSPECTION ........................................................................................3-44
SPOKE INSPECTION AND TIGHTENING ........................................................3-44
CABLE INSPECTION..........................................................................................3-45
LEVER AND PEDAL LUBRICATION ..................................................................3-45
SIDESTAND LUBRICATION ..............................................................................3-46
REAR SUSPENSION LUBRICATION ................................................................3-46
ProCarManuals.com
Page 55 of 382
INSP
ADJINTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-1
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended inspections and adjustments.
These preventive maintenance procedures, if followed, will ensure more reliable vehicle operation and a
longer service life. The need for costly overhaul work will be greatly reduced. This information applies to
vehicles already in service as well as to new vehicles that are being prepared for sale. All service techni-
cians should be familiar with this entire chapter.
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
1
*Fuel line• Check fuel hoses for cracks or damage. ✓✓ ✓✓ ✓•
• Check condition.
✓✓
2 Spurk plug• Clean and regap.
• Replace.✓✓
3 * Valves• Check valve clearance.
✓✓ ✓✓
• Adjust.
4Air filter element• Clean.✓✓
• Replace. ✓✓
5 Clutch• Check operation.
✓✓ ✓ ✓✓
• Adjust.
• Check operation, fluid level and vehicle for fluid leakeage.
6 * Front brake•(See NOTE). ✓✓ ✓ ✓✓ ✓•
• Replace brake pads. Whenever worm to the limit
• Check operation, fluid level and vehicle
•for fluid leakage. ✓✓ ✓ ✓✓ ✓
7 * Rear brake•(See NOTE).
• Replace brake pads. Whenever worm to the limit
8 * Brake hoses• Check for cracks or damage.✓✓✓✓ ✓• Replace. (See NOTE). Every 4 years
9 * Wheels• Check runout, spoke tightness and for damage.
✓✓✓ ✓
• Tighten spokes if necessary.
• Check tread depth and for damage.
10 * Tyres• Replace if necessary.
✓✓✓✓ ✓
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings• Check bearing for looseness or damage.✓✓✓✓
12 * Swingarm• Check operation and for excessive play.✓✓✓✓
• Check chain slack.
13 * Drive chain• Make sure that the rear wheel is properly aligned.Every 500 km and after washing the
• Clean and lubricate.motorcycle or riding in the rain.
14 *Steering • Check bearing play and steering for roughness. ✓✓ ✓ ✓✓bearings
• Lubrificate with lithium-soap-based grease. Every 20,000 km
15 *Chassis • Make sure that all nuts, bolts and screws are properly
✓✓ ✓✓ ✓
fasteners•tightened.
16Sidestand• Check operation.
✓✓ ✓✓ ✓
• Lubricate.
17
*Sidestand
• Check operation and for oil leakage. ✓✓ ✓ ✓✓ ✓
switch
ProCarManuals.com
Page 56 of 382
INTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-2
INSP
ADJ
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
18 * Rear brake• Check operation, fluid level and vehicle for fluid leakage. ✓✓✓ ✓
Rear shock
• Check operation and shock absorber for oil leakage.
19
*absorber ✓✓✓ ✓
assemblysull’ammortizzatore.
Rear suspension
• Check operation.
✓✓✓ ✓
20*
relay arm and
connecting arm
• Lubricate with lithium-soap-based grease.
✓✓
pivoting points
• Check starter (choke) operation.
21 * Carburator
• Adjust engine idling speed.✓✓ ✓✓ ✓ ✓
22 Engine oil• Change.
✓✓ ✓✓ ✓ ✓
• Check oil level and oil leakage.
23Engine oil filter
• Replace.✓✓✓
element
24 *Front and rear •
brake switches• Check operation.✓✓ ✓✓ ✓ ✓
Moving parts
25
and cables• Lubricate. ✓✓✓ ✓ ✓
Throttle grip • Check operation and free play.
26 * housing and • Adjust the throttle cable free play if necessary.
✓✓✓ ✓ ✓
cable • Lubricate the throttle grip housing and cable.
27 *Muffler and
• Check the screw clamp for looseness. ✓
exhaust pipe
28 *Lights, signals • Check operation.
✓✓ ✓✓ ✓ ✓
and switches• Adjust headlight beam.
* Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,
data and technical skills.
NOTE:
• The annual checks must be performed every year, except if a kilometer-based maintenance is per-
formed instead.
• From 50,000 km, repeat the maintenance intervals starting from 10,000 km.
• The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
• Hydraulic brake system:
• Check the brake fluid level regularly and fill as required.
• Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
• Replace the brake hoses every four years or if cracked or damaged.
ProCarManuals.com
Page 71 of 382
INSP
ADJ
3-17
ENGINE OIL REPLACEMENT
ENGINE OIL REPLACEMENT
Do not put additives into the engine oil. The
latter also lubricates the clutch and additives
might cause it to slide.
WARNING
Never remove the oil tank cap when the
engine is hot. The boiling oil might spill over,
causing burns. Wait for the oil to cool to at
least 60°C (140°F) or thereabouts.
Engine oil replacement (without replacing filter
oil)
1. Warm up the engine for a few minutes.
2. Stop the engine. Place an oil pan under the
engine and remove the oil filler cap.
3. Remove the drain plug (1) and drain the
engine oil.
4. Remove two bolts (2) and O-ring of the oil
hose flange, and drain the oil from oil tank.
CAUTION:
7. Inspect:
•All gaskets
Damaged ➔Replace.
8. Reassemble:
•Oil filter cover bleeder screw
•Engine oil drain plug
•Oil tank hose and O-ring 5. Remove the air bleed screw (3) attached to
the oil filter cover (4).
6. Wait until the oil has completely drained.
ProCarManuals.com
Page 72 of 382
3-18
INSP
ADJ
ENGINE OIL REPLACEMENT
Fastening torques:
Drain plug (engine):
30 Nm (3.0 mkg)
Oil tank hose (flange):
10 Nm (1.0 mkg)
Oil filter cover air bleeder screw:
5 Nm (0.5 mkg)
9. Fill:
•Oil tank
Recommended oil:
SAE20W40SE or SAE10W30SE
Refer to the chart for selection of
the oils suited to the atmospheric
temperature.
API Standard:
API SE, SF, SG or higher grade
Oil capacity:
Periodic change = 2.4 litres
•Do not put in any chemical additives or
use oils with a grade of CD (a) or higher.
•Be sure not to use oils labeled “ENERGY
CONSERVING II” (b) or higher. Engine oil
also lubricates the clutch and additives
could cause clutch slippage.
•Be sure no foreign material enters the
crankcase.
CAUTION:
10. Install:
•Oil tank tap
11. Check:
•Oil level
See section “ENGINE OIL LEVEL
CHECK”.
•Oil pressure
See section “ENGINE OIL PRESSURE
CHECK”.
•Oil leakage
ProCarManuals.com