fuses YAMAHA TT600RE 2004 Service Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: TT600RE, Model: YAMAHA TT600RE 2004Pages: 382, PDF Size: 6.39 MB
Page 54 of 382

INSP
ADJ
ELECTRICAL SYSTEM............................................................................................3-47
CHECKING AND CHARGING THE BATTERY ..................................................3-47
CHECKING THE FUSES ....................................................................................3-53
REPLACING THE HEADLIGHT BULBS ............................................................3-54
REPLACING THE TURN INDICATOR LIGHT BULB ..........................................3-56
REPLACING THE TAIL/BRAKE LIGHT BULB ....................................................3-57
ProCarManuals.com
Page 107 of 382

INSP
ADJ
CHECKING THE FUSES
3-53
CHECKING THE FUSES
To avoid a short circuit, always turn the main
switch to "OFF" when checking or replacing a
fuse.
1. Remove:
•Seat
•Panel 1
2. Check:
•Fuse
CAUTION:
a. Connect the pocket tester to the fuse and
check it for continuity.
NOTE:
Set the pocket tester selector to “Ω1”.
b. If the pocket tester indicates "∞", replace the
fuse.
3. Replace:
•Blown fuse
a. Turn off the ignition.
b. Install a new fuse of the correct amperage rat-
ing.
c. Turn on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check the
electrical circuit.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Pocket tester
90890-03112
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
FusesAmperage
Quantityrating
Main (1) 20 A 1
Reserve (2) 20 A 1
ProCarManuals.com
Page 108 of 382

CHECKING THE FUSES/
REPLACING THE HEADLIGHT BULBS
3-54
INSP
ADJ
WARNING
Never use a fuse with an amperage rating
other than that specified. Improvising or using
a fuse with the wrong amperage rating may
cause extensive damage to the electrical sys-
tem, cause the lighting and ignition systems
to malfunction and could possibly cause a fire.
4. Install:
•Pannel
•Seat
REPLACING THE HEADLIGHT BULBS
Low beam/high beam
1. Remove:
•Cowling screws (1)
2. Remove:
•Cowling (from the meter bracket)
NOTE:
Remove the cowling from the meter bracket by
lowering it to disengage it, and then lifting it up.
3. Remove:
•Headlight (2)
4. Disconnect:
•Headlight coupler (3)
5. Remove:
•Headlight bulb cover (4)
6. Remove:
•Headlight bulb holder (5) (by turning it
counterclockwise (a))
•Headlight bulb
WARNING
Headlight bulbs get very hot. Therefore, keep
flammable products away from a lit headlight
bulb, and do not touch the bulb until it has
cooled down.
ProCarManuals.com
Page 317 of 382

ELECIGNITION SYSTEM
7-13
DIAGNOSTICS IF THE IGNITION SYSTEM WERE TO STOP WORKING (NO OR INTERMITTENT SPARK)
Procedure
Check:
1. Fuse
2. Battery
3. Spark plug
4. Amplitude of ignition spark
5. Spark plug cap resistance
6. Ignition winding resistance 7. Main switch
8. Engine stop switch
9. Sidestand switch
10. Neutral switch
11. Clutch switch
12. Pick-up coil resistance
13. Wiring connections (whole connection sys- tem)
NOTE:
Before making the inspections mentioned, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check functioning defects use the following special tools.
Dinamic spark tester: P/N. 90890-06754
Pocket tester:P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
2.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com
Page 328 of 382

ELECTRICAL STARTING SYSTEM
7-24
ELEC
DIAGNOSTICS THE STARTER FAILS TO WORK
Procedure
Inspect:
(1) Fuse
(2) Battery
(3) Starting motor
(4) Starter relay
(5) Main switch (6) Engine stop switch
(7) Sidestand switch
(8) Neutral switch
(9) Clutch switch
(10) Starter switch
(11) Harness connections
NOTE:
Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check for defects use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse.
•Remove fuse.
•Connect the pocket tester ( Ωx 1) to the
fuse.
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
2. Battery.
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
CONTINUITY
DISCONTINUTY
Replace the fuse.
INCORRECT
•Clean the battery terminals.
•Recharge or replace the battery.
Refer to “BATTERY INSPECTION” in
Chapter 3.
*
CORRECT
ProCarManuals.com
Page 341 of 382

ELECCHARGING SYSTEM
7-37
DIAGNOSTICS THE BATTERY IS NOT BEING CHARGED
Procedure
Inspect:
1. Fuse
2. Battery
3. Charging voltage 4. Stator winding resistance
5. Harness connection (whole connection system)
NOTE:
Before starting inspections, remove the following parts: 1. Seat
2. Rear cowling
•To check for defects use the following special tools.
Inductive rev counter: P/N. 90890-03113
Pocket tester:P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com
Page 347 of 382

ELECLIGHT SYSTEM
7-43
DIAGNOSTICS THE HIGH BEAM LIGHT, PARKING INDICATOR LIGHT, REAR LIGHT, FRONT PARKING LIGHT AND/OR INSTRUMENT LIGHTS FAIL TO TURN ON.
Procedure
Inspect:
1. Fuse
2. Battery
3. Main switch 4. Dipped/high beam light and dimmer switch
5. Relay assy
6. Harness connections (full system of connec- tions)
NOTE:
•Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling
3. Cowling (headlight)
4. Tail light cover
•To check for defects use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com
Page 357 of 382

ELECSIGNAL SYSTEM
7-53
DIAGNOSTICS
•THE FLASHER LIGHTS, BRAKE LIGHT AND/OR WARNING LIGHTS FAIL TO TURN ON.
•THE HORN FAILS TO SOUND.
Procedure
Check:
1. Fuse
2. Battery
3. Main switch
4. Harness connections (entire system of con- nections)
NOTE:
•Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling
3. Cowling (headlight)
4. Tail light cover
•To check for operating faults use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery.
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com