oil filter YAMAHA TT600RE 2004 Service Manual

SPECGENERAL SPECIFICATIONS
2-1
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item Standard Limit
ModelTT600RE: 5CH5
Dimensions
Overall length 2,220 mm •••
Overall width 865 mm •••
Overall height 1,195 mm •••
Seat height 890 mm •••
Wheelbase 1,480 mm •••
Ground clearance 280 mm •••
Minimum turning radius 3,300 mm (right)
3,100 mm (left) •••
Basic weight (with oil and full
fuel tank)164.5 kg •••
Engine
Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined single cylinder
Displacement 595 cm
3•••
Bore x stroke 95.0 x 84.0 mm •••
Compression ratio 8.5 : 1 •••
Starting system Electric starter
Lubrication system Dry sump with separate oil tank
Engine oil
Type
Temp. °CSAE20W40SE or SAE10W30SE •••
Recommended engine oil classification API Service SE, SF, SG or higher •••
Quantity:
Without oil filter cartridge
replacement 2.4 L •••
With oil filter cartridge
replacement 2.5 L •••
Total amount (dry engine) 3.0 L •••
Air filterWet type element
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 10 L •••
Fuel reserve amount 3.0 L •••
Carburetor
Manufacturer TEIKEI
Model x quantity Y30PV-2ATK x 1
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-8
Item Standard Limit
Ballancer
Ballancer drive method Gear
Clutch
Clutch release method Inner push, cam push
Friction plate thickness 2.72 - 2.88 mm •••
Wear limit ••• 2.60 mm
Plate quantity 6 pcs
Friction plate thickness 2.94 - 3.06 mm •••
Wear limit ••• 2.8 mm
Plate quantity 2 pcs
Clutch plate thickness 1.20 mm •••
Plate quantity 7 pcs
Max. warpage ••• 0.20 mm
Clutch spring free length 42.8 mm •••
Plate quantity 5 pcs
Clutch housing thrust clearance 0.070 - 0.071 mm •••
Transmission
Max. main axle runout ••• 0.08 mm
Max. drive axle runout ••• 0.08 mm
Shift mechanism type Cam drum and guide bar
Carburetor
ID mark 5CH5 10
Main jet #1:#150 #2:#145
Main air jet #1:1.0 #2:0.9
Jet needle #1:5C5A-3/5 #2:5Y18-3/5
Needle jet 2.600
Cutaway 4.00
Pilot air jet 1 # 0.8 mm
Pilot jet # 50
Bypass 1 # 1.0
Pilot screw turns out 2-3/4 +/- 1/2
Valve seat size 2.5
Starter jet 1 # 74
Float height 6.0 - 8.0 mm •••
Engine idle speed1,150-1,450 r/min •••
CO% 1.5 - 3 •••
Intake vacuum 30.6-33.36 kPa - 230-250 mm Hg •••
Lubrication systemDry sump
Oil filter type Paper type
Oil pump:
Oil pump type Trochoid type
Inner rotor to outer rotor tip clearance 0.12 mm 0.20 mm
Outer rotor to pump housing
clearance 0.030 - 0.080 mm 0.150 mm
Bypass valve opening pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm
2) •••
Relief valve operating pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm2) •••
Oil pressure (hot) 13.0 kPa (0.13 kgf/cm2)/1,300 r/min •••
Pressure check location Oil filter chamber •••
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-10
Tightening
Part torque
Part to be tightened
nameThread size Remarks
Nm mkg
Cylinder head Washer
based bol M8 x 1.25 29 2.9
Cylinder head Stud bolt M10 x 1.25 20 2.0
Cylinder head Hexagon socket
head screw M6 x 1.0 10 1.0
Cylinder head Stud bolt M6 x 1.0 7 0.7
Cylinder head:
Cap (oil check) Union bolt M6 x 1.0 7 0.7
Spark plug – M12 x 1.25 18 1.8
Cylinder head cover Hexagon socket
head screw M6 x 1.0 10 1.0
Tappet cover (intake) Hexagon socket
head screw M6 x 1.0 10 1.0
Tappet cover (exhaust) – M32 x 1.5 12 1.2
Cylinder Crown nut M8 x 1.25 22 2.2
Cylinder Nut M10 x 1.25 42 4.2
Cylinder Hexagon socket
head screw M6 x 1.0 10 1.0
Weight drive gear Hexagon nut M16 x 1.0 60 6.0
Rotor (A.C. magneto) Hexagon nut M14 x 1.5 120 12.0
Lock nut (valve adjusting screw) Hexagon nut M6 x 1.0 14 1.4
Cam chain sprocket Washer based
bolt M7 x 1.0 20 2.0
Cam chain stopper guide Hexagon socket
head screw M6 x 1.0 10 1.0
Cam chain stopper guide Washer based
screw M16 x 1.0 20 2.0
Rocker shaft Hexagon socket
head screw M6 x 1.0 10 1.0
Oil pump Hexagon socket
head screw M6 x 1.0 10 1.0
Oil delivery/retrieval pipe Pan screw M6 x 1.0 7 0.7
Oil draining pipe Washer based
screw M14 x 1.5 30 3.0
Oil filter cover Hexagon socket
head screw M6 x 1.0 10 1.0
Bleed screw (oil filter cover) Hexagon screw M5 x 0.8 5 0.5
Push lever (clutch) Pan screw M8 x 1.0 12 1.2
Push rod (clutch) Hexagon nut M6 x 1.0 8 0.8
Sprocket Hexagon nut M18 x 1.0 115 11.5
Lock washer (oil seal) Hexagon screw M6 x 1.0 10 1.0
Stop lever Bolt M6 x 1.0 10 1.0
Shift cam Hexagon screw M6 x 1.0 10 1.0
Stator Pan head (+)
screw M5 x 0.8 5 0.5
Tightening torques
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-11
Tightening
Part torque
Part to be tightened
nameThread size Remarks
Nm mkg
Stator (pick-up coil) Hexagon socket
head screw M6 x 1.0 7 0.7
Engine oil pipe 1 Hexagon socket
head screw M6 x 1.0 10 1.0
Engine oil pipe 2 Union screw M12 x 1.25 35 3.5
Oil delivery pipe Union bolt M8 x 1.25 18 1.8
Carburetor joints Hexagon socket
head screw M6 x 1.0 10 1.0
Air filter case (frame) Hexagon screw M6 x 1.0 10 1.0
Air filter case (frame) Washer based
screw M6 x 1.0 10 1.0
Exhaust pipe Washer based
nut M6 x 1.0 10 1.0
Exhaust pipe protector Pan head (+)
screw M6 x 1.0 7 0.7
Muffler Hexagon socket
head screw M8 x 1.25 23 2.3
Muffler (band) Nut, nylon M8 x 1.25 23 2.3
Muffler Washer based
screw M8 x 1.25 23 2.3
Crankcase Hexagon socket
head screw M6 x 1.0 10 1.0
Crankcase Stud bolt M10 x 1.25 20 2.0
Crankcase cover (right) Hexagon socket
head screw M6 x 1.0 10 1.0
Crankcase cover (left) Hexagon socket
head screw M6 x 1.0 10 1.0
Sprocket cover Hexagon socket
head screw M6 x 1.0 10 1.0
Stop washer (bearing) Flat headscrew M6 x 1.0 7 0.7
Pressure plate Washer based
screw M6 x 1.0 8 0.8
Clutch housing Hexagon nut M20 x 1.0 90 9.0
Primary drive gear Hexagon nut M20 x 1.0 120 12.0
ProCarManuals.com

2-22
SPECLUBRICATION LAYOUT
LUBRICATION LAYOUT
(1) Oil tank
(2) Oil pump
(3) Oil filter (oil tank)
(4) Oil strainer (engine)
(5) Oil vapour retrieval hose
(6) Oil blow-by retrieval hose[A] DELIVERY
[B] RETRIEVAL
ProCarManuals.com

SPECLUBRICATION LAYOUT
2-23
(1) Oil pump
(2) Oil filter
(3) Camshaft
(4) Oil delivery hose
(5) Main driving shaft
(6) Drive shaft[A] DELIVERY
[B] RETRIEVAL
A
B
ProCarManuals.com

SPECLUBRICATION LAYOUT
2-24
(1) Oil filter
(2) Camshaft
(3) Connecting rod pin
(4) Main driving shaft
(5) Secondary drive shaft
(6) Drain plug[A] DELIVERY
[B] RETRIEVAL
A
B
ProCarManuals.com

SPECLUBRICATION LAYOUT
2-25
(1) Oil pump
(2) Oil filter
(3) Oil delivery hose
(4) Transmission
(5) Oil strainer[A] DELIVERY
[B] RETRIEVAL
A
B
ProCarManuals.com

INSP
ADJ
CHAPTER 3.
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION..........................................................................................................3-1
PERIODIC MAINTENANCE/LUBRICATION INTERVALS........................................3-1
SEAT, FUEL TANK AND REAR COWLING................................................................3-3
REMOVAL ............................................................................................................3-3
INSTALLATION ....................................................................................................3-3
ENGINE........................................................................................................................3-4
VALVE CLEARANCE ADJUSTMENT ..................................................................3-4
DRIVE CHAIN ADJUSTMENT ..............................................................................3-7
IDLE SPEED ADJUSTMENT ................................................................................3-7
THROTTLE CABLE FREE PLAY ADJUSTMENT ................................................3-8
SPARK PLUG INSPECTION ................................................................................3-9
IGNITION TIMING CHECK ................................................................................3-11
COMPRESSION INSPECTION ..........................................................................3-12
ENGINE OIL LEVEL CHECK ..............................................................................3-15
ENGINE OIL REPLACEMENT ............................................................................3-17
ENGINE OIL PRESSURE CHECK ....................................................................3-21
CLUTCH ADJUSTMENT ....................................................................................3-21
AIR FILTER CLEANING ......................................................................................3-24
FUEL FILTER CLEANING ..................................................................................3-25
ENGINE OIL TANK FILTER CLEANING ............................................................3-26
SUCTION HOSE AND MANIFOLD INSPECTION..............................................3-28
FUEL LINE INSPECTION ..................................................................................3-28
CRANKCASE VENTILATION HOSE INSPECTION ..........................................3-29
EXHAUST SYSTEM INSPECTION ....................................................................3-29
CHASSIS....................................................................................................................3-30
ADJUSTING THE FRONT BRAKE ....................................................................3-30
ADJUSTING THE REAR BRAKE ......................................................................3-31
CHECKING THE BRAKE FLUID LEVEL ............................................................3-32
BRAKE PAD WEAR INSPECTION ....................................................................3-33
BRAKE HOSING INSPECTION ..........................................................................3-33
BRAKE CIRCUIT BLEEDING ............................................................................3-34
DRIVE CHAIN SLACK INSPECTION AND ADJUSTMENT..................................3-35
DRIVE CHAIN LUBRICATION ............................................................................3-36
FRONT FORK INSPECTION ..............................................................................3-37
ADJUSTING THE FRONT FORK ......................................................................3-37
REAR SHOCK ABSORBER ADJUSTMENT ......................................................3-38
STEERING INSPECTION ..................................................................................3-40
TYRE INSPECTION ............................................................................................3-41
WHEEL INSPECTION ........................................................................................3-44
SPOKE INSPECTION AND TIGHTENING ........................................................3-44
CABLE INSPECTION..........................................................................................3-45
LEVER AND PEDAL LUBRICATION ..................................................................3-45
SIDESTAND LUBRICATION ..............................................................................3-46
REAR SUSPENSION LUBRICATION ................................................................3-46
ProCarManuals.com

INSP
ADJINTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-1
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended inspections and adjustments.
These preventive maintenance procedures, if followed, will ensure more reliable vehicle operation and a
longer service life. The need for costly overhaul work will be greatly reduced. This information applies to
vehicles already in service as well as to new vehicles that are being prepared for sale. All service techni-
cians should be familiar with this entire chapter.
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
1
*Fuel line• Check fuel hoses for cracks or damage. ✓✓ ✓✓ ✓•
• Check condition.
✓✓
2 Spurk plug• Clean and regap.
• Replace.✓✓
3 * Valves• Check valve clearance.
✓✓ ✓✓
• Adjust.
4Air filter element• Clean.✓✓
• Replace. ✓✓
5 Clutch• Check operation.
✓✓ ✓ ✓✓
• Adjust.
• Check operation, fluid level and vehicle for fluid leakeage.
6 * Front brake•(See NOTE). ✓✓ ✓ ✓✓ ✓•
• Replace brake pads. Whenever worm to the limit
• Check operation, fluid level and vehicle
•for fluid leakage. ✓✓ ✓ ✓✓ ✓
7 * Rear brake•(See NOTE).
• Replace brake pads. Whenever worm to the limit
8 * Brake hoses• Check for cracks or damage.✓✓✓✓ ✓• Replace. (See NOTE). Every 4 years
9 * Wheels• Check runout, spoke tightness and for damage.
✓✓✓ ✓
• Tighten spokes if necessary.
• Check tread depth and for damage.
10 * Tyres• Replace if necessary.
✓✓✓✓ ✓
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings• Check bearing for looseness or damage.✓✓✓✓
12 * Swingarm• Check operation and for excessive play.✓✓✓✓
• Check chain slack.
13 * Drive chain• Make sure that the rear wheel is properly aligned.Every 500 km and after washing the
• Clean and lubricate.motorcycle or riding in the rain.
14 *Steering • Check bearing play and steering for roughness. ✓✓ ✓ ✓✓bearings
• Lubrificate with lithium-soap-based grease. Every 20,000 km
15 *Chassis • Make sure that all nuts, bolts and screws are properly
✓✓ ✓✓ ✓
fasteners•tightened.
16Sidestand• Check operation.
✓✓ ✓✓ ✓
• Lubricate.
17
*Sidestand
• Check operation and for oil leakage. ✓✓ ✓ ✓✓ ✓
switch
ProCarManuals.com