oil YAMAHA TTR125 2006 Owner's Guide

3 - 1
INSP
ADJ
MAINTENANCE INTERVALS
EC300000
REGULAR INSPECTION AND ADJUSTMENTS
MAINTENANCE INTERVALS
The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind
that such factors as weather, terrain, geographical location, and individual usage will alter the
required maintenance and lubrication intervals. If you are a doubt as to what intervals to follow in
maintaining and lubricating your machine, consult your Yamaha dealer.
Dealer
NoteItem Checks and maintenance jobsInitial Every
10 hours
(1 month)60 hours
(6 months)120 hours
(12 months)
*Fuel lineCheck fuel hoses for cracks or damage.
Replace if necessary.
Spark plugCheck condition.
Clean, regap or replace if necessary.
*ValvesCheck valve clearance.
Adjust if necessary.
Air filter Clean or replace element if necessary.
*CarburetorCheck engine idling speed and starter operation.
Adjust if necessary.
Exhaust systemsCheck for leakage.
Retighten if necessary.
Replace gasket if necessary.
Engine oilCheck oil level and vehicle for oil leakage.
Correct if necessary.
Change. (Warm engine before draining.)
ClutchCheck operation.
Adjust or replace cable.
*Front brakeCheck operation.
Adjust brake lever free play.
Check fluid level and leakage.
(TT-R125LW/TT-R125LWE only)Every ride
*Rear brakeCheck operation.
Adjust brake pedal free play and replace brake
shoes if necessary.Every ride
*WheelsCheck balance, runout, spoke tightness and for
damage.
Tighten spokes and rebalance, replace if
necessary.
*TiresCheck tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
*Wheel bearingsCheck bearing for looseness or damage.
Replace if necessary.
*SwingarmCheck swingarm pivoting point for play.
Correct if necessary.
Lubricate with molybdenum disulfide grease.
Drive chainCheck chain slack.
Adjust if necessary. Make sure that the rear wheel
is properly aligned.
Clean and lubricate.Every ride
*Steering bearingsCheck bearing play and steering for roughness.
Correct accordingly.
Lubricate with lithium soap base grease every 120
hours.

3 - 2
INSP
ADJ
MAINTENANCE INTERVALS
*: Since these items requires special tools data and technical skills, they should be serviced.*1: For USA
SidestandCheck operation.
Lubricate and repair if necessary.
*Spark arrester*1Clean.
*Front forkCheck operation and for oil leakage.
Correct accordingly.
*
Rear shock
absorber assemblyCheck operation and shock absorber for oil
leakage.
Replace shock absorber assembly if necessary.
*Chassis fastenersMake sure that all nuts, bolts and screws are
properly tightened.
Tighten if necessary.
Battery (TT-R125E/
TT-R125LWE only)Check terminal for looseness and corrosion.
Tighten or clean if necessary.
Dealer
NoteItem Checks and maintenance jobsInitial Every
10 hours
(1 month)60 hours
(6 months)120 hours
(12 months)
3

INSPADJ
PROGRAMME D’ENTRETIEN
CONTRÔLES ET RÉGLAGES PÉRIODIQUES
PROGRAMME D’ENTRETIEN
Le programme suivant est destiné à servir de guide général p\
our l’entretien et le graissage. Garder à l’esprit
que les intervalles d’entretien et de graissage varient en fonction d\
es conditions atmosphériques, du terrain, de
l’altitude et de l’utilisation du véhicule. Si une question se \
pose quant aux fréquences auxquelles un entretien
doit être effectué, demander conseil à son concessionnaire Yamaha.
3 - 1
No.Éléments Contrôles et travaux d'entretien le premier
réaliséInitial
heures Tous les
1
mois
612
30 60 120
√√
√√ √
√ √
√ √
√
√√
√ √
√
√ √
√
√ √
√
√ √
√
√
√ √
√
√ √
√
√
√
√
√
√ √
√1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17 Canalisation de
carburant
*
*
*
*
*
*
*
*
*
*
*
* *Contrôler si les flexibles de carburant ne sont ni craquelés ni
endommagés. Remplacer si nécessaire.
Bougie Vérifier l'état.
Régler l'écartement et nettoyer.
Jeu de soupapes Contrôler et régler le jeu de soupapes machine à froid.
Filtre à air Nettoyer avec du solvant.
Remplacer si nécessaire.
Carburateur Contrôler le régime de ralenti et le fonctionnement du démarreu\
r.
Régler si nécessaire.
Système
d'échappement Contrôler l'étanchéité.
Resserrer si nécessaire.
Remplacer le joint si nécessaire.
Huile de moteur Changer (Faire chauffer le moteur avant la vidange).
Embrayage Vérifier le fonctionnement.
Régler ou remplacer le câble.
Frein avant (TT-R125/TT-R125E)
Vérifier le fonctionnement.
Régler la garde du levier de frein et remplacer les mâchoires de f\
rein si nécessaire.(TT-R125LW/TT-R125LWE)Vérifier le fonctionnement, le niveau du liquide, et s'assurer qu'il \
n'y a pas de fuite.Remplacer les mâchoires de frein si nécessaire.
Tous les ans
Frein arrière Vérifier le fonctionnement.
Régler la garde du levier de frein et remplacer les mâchoires de f\
rein si nécessaire.
Flexible de frein
(TT-R125LW/
TT-R125LWE) Contrôler d'éventuels claquements ou
endommagements.
Remplacer.
Contrôler le voile, le serrage des rayons et le bon état géné\
ral.
Serrer les rayons si nécessaire.
Roues
Pneus Contrôler la profondeur de sculpture et l'état des pneus.
Remplacer si nécessaire.
Contrôler la pression de gonflage.
Corriger si nécessaire.
Roulements de roue Contrôler les roulements pour un fonctionnement en douceur.
Remplacer si nécessaire.
Bras oscillant Contrôler le jeu au pivot du bras oscillant.
Corriger si nécessaire.
Lubrifier à la graisse à base de savon au lithium
Chaîne de
transmission Contrôler la flèche et l'alignement de la chaîne et son état\
.
Régler et lubrifier la chaîne.
Roulements de
direction S'assurer que les roulements n'ont pas de jeu.
Lubrifier à la graisse à base de savon au lithium toutes les 120 h\
eures ou 12 mois
(le premier réalisé). Tous les 4 ans
Every ride
Remplacer le liquide frein tous les ans. (TT-R125LW/TT-R125LWE)

3 - 3
INSP
ADJ
PRE-OPERATION INSPECTION AND MAINTENANCE
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation or practice, make sure the machine is in good operating condi-
tion.
Before using this machine, check the following points.
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
FuelCheck that a fresh gasoline is filled in the fuel tank. Check the
fuel line for leakage.P.1-12
Engine oilCheck that the oil level is correct. Check the crankcase for leak-
age.P.3-7 ~ 10
Gear shifter and clutchCheck that gears can be shifted correctly in order and that the
clutch operates smoothly.P.3-4
Throttle grip/housingCheck that the throttle grip operation and free play are correctly
adjusted. Lubricate the throttle grip and housing, if necessary.P.3-4 ~ 5
BrakesCheck the play of front and rear brake and effect of front and
rear brake.
Check fluid level and leakage. (TT-R125LW/TT-R125LWE only)P.3-15 ~ 20
Drive chainCheck chain slack and alignment. Check that the chain is lubri-
cated properly.P.3-21 ~ 22
WheelsCheck for excessive wear and tire pressure. Check for loose
spokes and have no excessive play.P.3-27 ~ 28
SteeringCheck that the handlebar can be turned smoothly and have no
excessive play.P.3-28 ~ 32
Front forks and rear shock
absorber assemblyCheck that they operate smoothly and there is no oil leakage. P.3-23 ~ 26
Cables (wires)Check that the clutch and throttle cables move smoothly. Check
that they are not caught when the handlebars are turned or
when the front forks travel up and down.—
Muffler Check that the muffler is tightly mounted and has no cracks. P.4-2
Sprocket Check that the driven sprocket tightening nut is not loose. P.3-20
Lubrication Check for smooth operation. Lubricate if necessary. P.3-33
Bolts and nuts Check the chassis and engine for loose bolts and nuts.—
Lead connectorsCheck that the CDI magneto, CDI unit, and ignition coil are con-
nected tightly.P.1-5

3 - 7
INSP
ADJ
ENGINE OIL LEVEL INSPECTION
6. Apply:
Foam-air-filter oil or engine mixing oil
To the element.
NOTE:
Squeeze out the excess oil. Element should be
wet but not dripping.
7. Install:
Air filter element 1
On air filter guide 2.
8. Apply:
Lithium soap base grease
On the matching surface a on air filter
element.
9. Install:
Air filter element 1
Washer 2
Wing nut 3
ENGINE OIL LEVEL INSPECTION
1. Start the engine, warm it up for several
minutes and wait for five minutes.
2. Place the machine on a level place and
hold it up on upright position by placing
the suitable stand under the engine.
3. Remove:
Dipstick 1

3 - 8
INSP
ADJ
ENGINE OIL LEVEL INSPECTION
4. Check:
Oil level
Oil level should be between maximum
a and minimum b marks.
Oil level is low → Add oil to proper
level.
NOTE:
When inspecting the oil level, do not screw the
dipstick into the oil tank. Insert the gauge
lightly.
(For USA and CDN)
CAUTION:
Do not add any chemical additives.
Engine oil also lubricates the clutch and
additives could cause clutch slippage.
Do not allow foreign material to enter the
crankcase.
Recommended oil:
At –10 ˚C (10 ˚F) or higher Å:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
At 5 ˚C (40 ˚F) or higher ı:
Yamalube 4 (20W-40) or SAE
20W-40 type SE motor oil
(Except for USA and CDN)
CAUTION:
Do not add any chemical additives or use
oils with a grade of CD a or higher.
Do not use oils labeled “ENERGY CON-
SERVING II” b or higher. Engine oil also
lubricates the clutch and additives could
cause clutch slippage.
Do not allow foreign materials to enter the
crankcase.
Recommended oil:
Refer to the following chart for
selection of oils which are suited
to the atmospheric temperatures.
Recommended engine oil classi-
fication:
API STANDARD:
API “SE” or higher grade
(Designed primarily for motor-
cycles)

3 - 9
INSP
ADJ
ENGINE OIL REPLACEMENT
5. Install:
Dipstick
6. Start the engine and let it warm up for
several minutes.
7. Turn off the engine and inspect the oil
level once again.
NOTE:
Wait a few minutes until the oil settles before
inspecting the oil level.
ENGINE OIL REPLACEMENT
1. Start the engine and warm it up for sev-
eral minutes and wait for five minute.
2. Place the machine on a level place and
hold it on upright position by placing the
suitable stand under the engine.
3. Place a suitable container under the
engine.
4. Remove:
Oil drain bolt 1
Dipstick 2
Drain the engine oil.
5. Install:
Copper washer
Oil drain bolt 1
New
T R..20 Nm (2.0 m · kg, 14 ft · lb)
6. Fill:
Engine oil
7. Check:
Oil leakage
8. Check:
Engine oil level
9. Install:
Dipstick 2
Oil capacity:
Periodic oil change:
1.0 L (0.88 Imp qt, 1.06 US qt)

3 - 10
INSP
ADJOIL PRESSURE INSPECTION/PILOT AIR SCREW
ADJUSTMENT/ENGINE IDLING SPEED ADJUSTMENT
OIL PRESSURE INSPECTION
1. Check:
Oil pressure
Checking steps:
Slightly loosen the oil pressure check bolt
1.
Start the engine and keep it idling until oil
starts to seep from the oil pressure check
bolt. If no oil comes out after one minute,
turn the engine off so it will not seize.
Check oil passages and oil pump for dam-
age or leakage.
Start the engine after solving the prob-
lem(s) and recheck the oil pressure.
Tighten the oil pressure check bolt.
T R..
Oil pressure check bolt:
7 Nm (0.7 m • kg, 5.1 ft • lb)
PILOT AIR SCREW ADJUSTMENT
1. Adjust:
Pilot air screw 1
Adjustment steps:
NOTE:
To optimize the fuel flow at a smaller throttle
opening, each machine’s pilot air screw has
been individually set at the factory. Before
adjusting the pilot air screw, turn it in fully
and count the number of turns. Record this
number as the factory-set number of turns
out.
Screw in the pilot air screw until it is lightly
seated.
Back out by the specified number of turns.
Pilot air screw:
2-1/2 ~ 3-1/2 turns out (example)
ENGINE IDLING SPEED ADJUSTMENT
1. Start the engine and thoroughly warm it
up.
2. Attach:
Inductive tachometer
To spark plug lead.
3. Adjust:
Engine idling speed

INSPADJNETTOYAGE DU PARE- ÉTINCELLES (pour les USA)
FUNKENL ÖSCHER REINIGEN (Nur USA)
FUNKENL ÖSCHER REINIGEN (Nur USA)
WARNUNG
 Sicherstellen, da ss Krümmer und Schall-
d ämpfer abgek ühlt sind, bevor der Fun-
kenl öscher gereinigt wird.
Motor beim Reinigen der Auspuffanlage
nicht starten.
1. Demontieren:
Schraube (Funkenl öscher) 1
2. Demontieren:
Funkenl öscher 1
Funkenl öscher aus dem Schalld ämp-
fer herausziehen.
3. Reinigen:
Funkenl öscher
Funkenl öscher vorsichtig ausklopfen
und anschlie ßend mit einer Drahtb ürste
alle Kohleablagerungen beseitigen.
4. Montieren:
Funkenl öscher
Funkenl öscher in den Schalld ämpfer
hineinschieben und auf die Bohrungen
f ü r die Schrauben ausrichten.
Schraube (Funkenl öscher)
T R..10 Nm (1,0 m · kg, 7,2 ft · lb)
NETTOYAGE DU PARE- ÉTINCELLES
(pour les USA)
AVERTISSEMENT
S ’assurer que le tuyau et pot d ’échappement
sont froids avant d ’effectuer le nettoyage du
pare- étincelles.
Ne pas mettre le moteur en marche pendant le
nettoyage du syst ème d ’échappement.
1. D époser:
Boulon (pare- étincelles) 1
2. D époser:
Pare- étincelles 1
Extraire le pare- étincelles du pot d ’échap-
pement.
3. Nettoyer:
Pare- étincelles
Tapoter l ég èrement le pare- étincelles, puis
nettoyer les d ép ôts de calamine à l ’aide
d ’une brosse à poils m étalliques.
4. Monter:
Pare- étincelles
Loger le pare- étincelles dans le pot
d ’é chappement et aligner les orifices de
boulon.
Boulon (pare- étincelles)
T R..10 Nm (1,0 m · kg, 7,2 ft · lb)
3 - 14

3 - 21
INSP
ADJ
DRIVE CHAIN INSPECTION
EC369002
DRIVE CHAIN INSPECTION
1. Remove:
Master link clip
Joint 1
Drive chain 2
2. Clean:
Drive chain
Place it in kerosene, and brush off as
much dirt as possible. Then remove the
chain from the kerosene and dry the
chain.
3. Measure:
Drive chain length (10 links) a
Out of specification → Replace.
Drive chain length (10 links):
: 121.4 mm (4.78 in)
4. Check:
Drive chain stiffness a
Clean and oil the chain and hold as
illustrated.
Stiff → Replace drive chain.
5. Install:
Drive chain 1
Joint 2
Master link clip 3
CAUTION:
Be sure to install the master link clip to the
direction as shown.
aTurning direction
New