service YAMAHA TW200 2002 User Guide

6-33
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01304
Rear wheel removalEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Remove the brake adjusting
nut and brake rod from the
brake cam lever.
1
2
3
4 5
1. Adjusting nut
2. Brake rod
3. Axle nut
4. Cotter pin
5. Chain adjusting plate
2. Remove the axle nut cotter pin
and loosen the axle nut.
3. Elevate the rear wheel by plac-
ing a suitable stand under the
engine.
4. Remove the axle nut.
5. Push the wheel forward and
remove the drive chain.
6. Pull out the axle and remove
the rear wheel assembly by
pulling it backwards.EAU01308
Rear wheel installation
1. Install the wheel assembly and
insert the axle from the left-
hand side. Be sure that the
chain adjusting plates are
installed with the punched side
outward and the slot in the
brake shoe plate is fit over the
stopper on the swingarm.
2. Install and adjust the drive
chain. (See page 6-22 for
details about adjusting the
drive chain slack.)
3. Install the axle nut and let the
motorcycle down.
4. Tighten the axle nut to the
specified torque and install the
axle nut cotter pin.
Tightening torque:
Axle nut:
90 Nm (9.0 m0kg)
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 62

6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EW000110
w
Always use a new cotter pin on
the axle nut.
5. Insert the brake rod into the
brake cam lever and install the
brake pedal free play adjusting
nut.
6. Adjust the rear brake pedal
free play. (See page 6-19.)
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
EAU01008Troubleshooting
Although Yamaha motorcycles
receive a rigid inspection before
shipment from the factory, trouble
may occur during operation.
Any problem in the fuel, compres-
sion, or ignition systems can cause
poor starting and loss of power.
The troubleshooting chart
describes a quick, easy procedure
for making checks.
If your motorcycle requires any
repair, bring it to a Yamaha dealer.
The skilled technicians at a
Yamaha dealership have the tools,
experience, and know-how to
properly service your motorcycle.
Use only genuine Yamaha parts on
your motorcycle. Imitation parts
may look like Yamaha parts, but
they are often inferior.
Consequently, they have a shorter
service life and can lead to expen-
sive repair bills.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 63

8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW200E
Dimensions:
Overall length 2,090 mm
Overall width 815 mm
Overall height 1,115 mm
Seat height 790 mm
Wheel base 1,325 mm
Ground clearance 250 mm
Minimum turning radius 1,900 mm
Basic weight (With oil and full
fuel tank):126 kg
Engine:
Engine type Air-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangement Forward inclined
single cylinder
Displacement 196 cm
3
Bore ×Stroke 67.0 ×55.7 mm
Compression ratio 9.5:1
Starting system Electric and kick starter
Lubrication system Wet sumpEngine oil:
Type:
Classification API Service “SE”, “SF” type
or equivalent
(e.g. “SF-SE”, “SF-SE-CC”,
“SF-SE-SD” etc.)
Capacity:
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filter:Wet type element
Fuel:
Type Regular gasoline
Fuel tank capacity 7.0 L
Reserve amount 1.7 L
Carburetor:
Type / quantity Y29P-5C / 1
Manufacturer TEIKEI
–10° 0° 10° 20° 30° 40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50C
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 67