transmission YAMAHA TZR50 2003 User Guide

The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Remove the oil check bolt, and
then check the oil level.
NOTE:
The oil should be at the brim of the
check hole.
3. If the oil is below the brim of the
check hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
4. Install the oil check bolt, and then
tighten it to the specified torque.
To change the transmission oil
1. Place an oil pan under the trans-
mission oil case to collect the used
oil.
2. Remove the drain bolt and the oil
check bolt to drain the oil.
3. Install the drain bolt and the
check bolt, and then tighten them to
the specified torque.4. Remove the oil filler cap, add the
specified amount of the recom-
mended transmission oil, and
then install and tighten the oil
filler cap.
ECAM1020
CAUTION
Make sure that no foreign material
enters the transmission case.
5. Start the engine and let it idle for
several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
Recommended transmission oil:
See page 8-1.
Oil change quantity:
0,75 L (0,65 imp.qt)
Tightening torque:
Transmission oil drain bolt:
17 Nm (1,7 m•kgf)
Oil check bolt:
3 Nm (0,3 m•kgf)
Tightening torque:
Oil check bolt:
3 Nm (0,3 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 39

EAU22760
Drive chain slack
(a) Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22771
To check the drive chain slack
1. Place the motorcycle on the
sidestand.
NOTE:
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
EAU22920
To adjust the drive chain slack
1. Cotter pin
2. Axle nut
3. Lock nut
4. Chain tensioner
1. Remove the cotter pin from the axle
nut, and then loosen the axle nut.
2. Loosen the chain puller locknut
at each end of the swingarm.
3. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction (a). To
loosen the drive chain, turn theadjusting nut at each end of the
swingarm in direction (b), and
then push the rear wheel forward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
ECA10570
CAUTION
Improper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
4. Tighten the locknuts, and then
tighten the axle nut to the speci-
fied torque.
5. Insert a new cotter pin into the
axle nut, and then bend its ends
as shown.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Drive chain slack:
40~50 mm (1,5 ~1,9 in)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16

a
a
b
2
1
4
3
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 48

EAU26339
Dimensions
Overall length
2007 mm
Overall width
675 mm
Overall height
1065 mm
Seat height
815 mm
Wheelbase
1330 mm
Ground clearance
144 mm
Minimum turning radius
2900 mm
Weight
With oil and fuel
124.2 kg
Engine
Engine type
Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.7 cm
3
Bore x stroke
40.3 x 39.0 mm
Compression ratio
6.85 :1
Starting system
Electric starter
Lubrication system
Separate lubrication (Yamaha autolube)
Transmission oil
Oil change quantity
0.75 L
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.71 L
Radiator capacity (including all routes)
0.70 L
Air filter element
Wet element
Fuel
Fuel tank capacity
13.8 L
Fuel reserve amount
2.2 L
Carburetor
Manufacturer
Dell’Orto
Type x quantity
PHBN 16 NS / 1
Spark plug (s)
Manufacturer/model
NGK/BR9ES
Spark plug gap
0.6-0.7 mm
Clutch type
Wet, multiple-disc
Transmission
Primary reduction system
Helical gear
Primary reduction ratio
71 x 20 (3.550)
Secondary reduction system
Chain driveSecondary reduction ratio
47 x 11 (4.270)
Transmission type
Constant mesh 6-speed
Gear ratio
1st
36 x 12 (3.000)
2nd
33 x 16 (2.062)
3rd
29 x 19 (1.526)
4th
27 x 22 (1.227)
5th
25 x 24 (1.041)
6th
24 x 25 (0.960)
Chassis
Frame type
Double cradle
Caster angle
25.00 degree
Trail
92.0 mm
Front tire
Type
Tubeless
Size
100/80-17 52H
Manufacturer/model
PIRELLI
Rear tire
Type
Tubeless
8
SPECIFICATIONS
8-1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 62

AAdjusting the brake pedal position and
free play .................................................6-13
Adjusting the carburetor ............................6-9
Adjusting the clucth lever free play .........6-12
Adjusting the engine idling speed .............6-9
Adjusting the rear brake light switch .......6-13
Adjusting the throttle cable free play .........6-9
BBattery......................................................6-19
Brake lever .................................................3-4
Brake pedal ................................................3-5
CCare............................................................7-1
Cast wheels .............................................6-12
Catalytic converter .....................................3-6
Clucht lever ................................................3-4
Controls and instruments ..........................2-3
Changing the brake fluid..........................6-15
Checking and lubricating the brake and
cluctch levers.........................................6-18
Checking and lubricating the brake
and shift pedals .....................................6-17
Checking and lubricating the cables .......6-17
Checking and lubricating the sidestand ..6-18
Checking the brake fluid level .................6-14
Checking the front fork ............................6-18
Checking the spark plug ............................6-6
Checking the steering ..............................6-19
Checking the wheel bearings ..................6-19
D2-stroke engine oil ........................................3-6
Drive Chain slack........................................6-16
EEngine break-in ..........................................5-3
Engine overheating ..................................6-25
FFrame serial number ..................................9-1
Front brake pads......................................6-14
Fuel cock....................................................3-6
Fuel tank cap .............................................3-5
HHandlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ....................3-8
Indicator lights ...........................................3-1
KKey identification number ..........................9-1
LLeft view .....................................................2-1
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
OOwner’s tool kit ..........................................6-1
PParking .......................................................5-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear brake pads ......................................6-14
Removing and installing cowlings .............6-5
Replacing a turn signal light bulb or the
tail/brake light bulb ................................6-21Replacing the fuse ...................................6-20
Replacing the headlight bulb ...................6-21
Replacing the license plate light bulb......6-22
Right view ..................................................2-2
SSeat ............................................................3-7
Shift pedal ..................................................3-4
Shifting .......................................................5-2
Sidestand ...................................................3-8
Speedometer unit ......................................3-2
Starter (choke) lever ...................................3-7
Starting a cold engine ................................5-1
Storage.......................................................7-2
Storage compartment ................................3-7
Supporting the mortorcycle .....................6-22
TTachometer ................................................3-3
Tips for reducing fuel consumption ...........5-2
Tires .........................................................6-10
To check the coolant level .........................6-8
Transmission oil .........................................6-6
Troubleshooting .......................................6-23
Troubleshooting charts ............................6-24
INDEX
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 66