check oil YAMAHA TZR50 2004 User Guide

EAU23140
Checking and lubricating the
brake and clutch levers
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
EAU23200
Checking and lubricating the
sidestand
The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA10730
s s
WARNING
If the sidestand does not move up
and down smoothly, have a Yama-
ha dealer check or repair it.
EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 50

2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
ECA10640
CAUTION
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer check
the electrical system.
EAU23800
Replacing the headlight bulb
This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1. Remove the headlight bulb cover,
and then disconnect the head-
light lead connectors.
2. Unhook the headlight bulb hol-der, and then remove the defecti-
ve bulb.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
3. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
4. Connect the headlight lead con-
nectors, and then install the bulb
cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24281
Replacing a turn signal light
bulb or the tail/brake light
bulb
1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
Specified fuse:
10 A
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 53

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
NOTE:
Consult a Yamaha dealer for advice
on what products to use.
EAU26150
Storage
Short-term
Always store your motorcycle in a
cool, dry place and, if necessary, pro-
tect it against dust with a porous
cover.
ECA10810
CAUTION
Storing the motorcycle in a
poorly ventilated room or cove-
ring it with a tarp, while it is still
wet, will allow water and humi-
dity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to
“OFF”.
3. Drain the carburetor float cham-
ber by loosening the drain bolt;
this will prevent fuel deposits
from building up. Pour the drai-
ned fuel into the fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking
during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
EWA10950
s s
WARNING
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
6. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
7
MOTORCYCLE CARE AND STORAGE
7-3
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 60

AAdjusting the brake pedal position and
free play .................................................6-13
Adjusting the carburetor ............................6-9
Adjusting the clucth lever free play .........6-12
Adjusting the engine idling speed .............6-9
Adjusting the rear brake light switch .......6-13
Adjusting the throttle cable free play .........6-9
BBattery......................................................6-19
Brake lever .................................................3-4
Brake pedal ................................................3-5
CCare............................................................7-1
Cast wheels .............................................6-12
Catalytic converter .....................................3-6
Clucht lever ................................................3-4
Controls and instruments ..........................2-3
Changing the brake fluid..........................6-15
Checking and lubricating the brake and
cluctch levers.........................................6-18
Checking and lubricating the brake
and shift pedals .....................................6-17
Checking and lubricating the cables .......6-17
Checking and lubricating the sidestand ..6-18
Checking the brake fluid level .................6-14
Checking the front fork ............................6-18
Checking the spark plug ............................6-6
Checking the steering ..............................6-19
Checking the wheel bearings ..................6-19
D2-stroke engine oil ........................................3-6
Drive Chain slack........................................6-16
EEngine break-in ..........................................5-3
Engine overheating ..................................6-25
FFrame serial number ..................................9-1
Front brake pads......................................6-14
Fuel cock....................................................3-6
Fuel tank cap .............................................3-5
HHandlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ....................3-8
Indicator lights ...........................................3-1
KKey identification number ..........................9-1
LLeft view .....................................................2-1
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
OOwner’s tool kit ..........................................6-1
PParking .......................................................5-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear brake pads ......................................6-14
Removing and installing cowlings .............6-5
Replacing a turn signal light bulb or the
tail/brake light bulb ................................6-21Replacing the fuse ...................................6-20
Replacing the headlight bulb ...................6-21
Replacing the license plate light bulb......6-22
Right view ..................................................2-2
SSeat ............................................................3-7
Shift pedal ..................................................3-4
Shifting .......................................................5-2
Sidestand ...................................................3-8
Speedometer unit ......................................3-2
Starter (choke) lever ...................................3-7
Starting a cold engine ................................5-1
Storage.......................................................7-2
Storage compartment ................................3-7
Supporting the mortorcycle .....................6-22
TTachometer ................................................3-3
Tips for reducing fuel consumption ...........5-2
Tires .........................................................6-10
To check the coolant level .........................6-8
Transmission oil .........................................6-6
Troubleshooting .......................................6-23
Troubleshooting charts ............................6-24
INDEX
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 66