clutch YAMAHA TZR50 2004 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: TZR50, Model: YAMAHA TZR50 2004Pages: 67, PDF Size: 1.4 MB
Page 45 of 67

adjusting nut in direction (b).
6. Tighten the locknut at the clutch
lever and the crankcase.
EAU22220
Adjusting the brake pedal
position and free play
1. Position adjusting bolt
2. Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
aligned with the top of the footrest as
shown. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.1. Loosen the locknut at the brake
pedal.
2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
1. Free play
The brake pedal free play should
measure 10~15 mm (0,39~59 in) at
the brake pedal end. Periodically
check the brake pedal free play and, if
necessary, adjust it as follows.To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10660
s s
WARNING
After adjusting the brake pedal free
play, check the operation of the
brake light.
EAU22270
Adjusting the rear brake light
switch
1. Switch
2. Lock nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
21
1
1
2a
b
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 45
Page 50 of 67

EAU23140
Checking and lubricating the
brake and clutch levers
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
EAU23200
Checking and lubricating the
sidestand
The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA10730
s s
WARNING
If the sidestand does not move up
and down smoothly, have a Yama-
ha dealer check or repair it.
EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 50
Page 62 of 67

EAU26339
Dimensions
Overall length
2007 mm
Overall width
675 mm
Overall height
1065 mm
Seat height
815 mm
Wheelbase
1330 mm
Ground clearance
144 mm
Minimum turning radius
2900 mm
Weight
With oil and fuel
124.2 kg
Engine
Engine type
Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.7 cm
3
Bore x stroke
40.3 x 39.0 mm
Compression ratio
6.85 :1
Starting system
Electric starter
Lubrication system
Separate lubrication (Yamaha autolube)
Transmission oil
Oil change quantity
0.75 L
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.71 L
Radiator capacity (including all routes)
0.70 L
Air filter element
Wet element
Fuel
Fuel tank capacity
13.8 L
Fuel reserve amount
2.2 L
Carburetor
Manufacturer
Dell’Orto
Type x quantity
PHBN 16 NS / 1
Spark plug (s)
Manufacturer/model
NGK/BR9ES
Spark plug gap
0.6-0.7 mm
Clutch type
Wet, multiple-disc
Transmission
Primary reduction system
Helical gear
Primary reduction ratio
71 x 20 (3.550)
Secondary reduction system
Chain driveSecondary reduction ratio
47 x 11 (4.270)
Transmission type
Constant mesh 6-speed
Gear ratio
1st
36 x 12 (3.000)
2nd
33 x 16 (2.062)
3rd
29 x 19 (1.526)
4th
27 x 22 (1.227)
5th
25 x 24 (1.041)
6th
24 x 25 (0.960)
Chassis
Frame type
Double cradle
Caster angle
25.00 degree
Trail
92.0 mm
Front tire
Type
Tubeless
Size
100/80-17 52H
Manufacturer/model
PIRELLI
Rear tire
Type
Tubeless
8
SPECIFICATIONS
8-1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 62