lock YAMAHA TZR50 2004 User Guide

EAU22760
Drive chain slack
(a) Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22771
To check the drive chain slack
1. Place the motorcycle on the
sidestand.
NOTE:
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
EAU22920
To adjust the drive chain slack
1. Cotter pin
2. Axle nut
3. Lock nut
4. Chain tensioner
1. Remove the cotter pin from the axle
nut, and then loosen the axle nut.
2. Loosen the chain puller locknut
at each end of the swingarm.
3. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction (a). To
loosen the drive chain, turn theadjusting nut at each end of the
swingarm in direction (b), and
then push the rear wheel forward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
ECA10570
CAUTION
Improper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
4. Tighten the locknuts, and then
tighten the axle nut to the speci-
fied torque.
5. Insert a new cotter pin into the
axle nut, and then bend its ends
as shown.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Drive chain slack:
40~50 mm (1,5 ~1,9 in)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16

a
a
b
2
1
4
3
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 48

2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
ECA10640
CAUTION
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer check
the electrical system.
EAU23800
Replacing the headlight bulb
This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1. Remove the headlight bulb cover,
and then disconnect the head-
light lead connectors.
2. Unhook the headlight bulb hol-der, and then remove the defecti-
ve bulb.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
3. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
4. Connect the headlight lead con-
nectors, and then install the bulb
cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24281
Replacing a turn signal light
bulb or the tail/brake light
bulb
1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
Specified fuse:
10 A
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 53

Engine overheatingEWA10400
s s
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the his-
sing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
6Wait until the
engine has cooled.Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See NOTE.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
NOTE:
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended
coolant as soon as possible.
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 57

AAdjusting the brake pedal position and
free play .................................................6-13
Adjusting the carburetor ............................6-9
Adjusting the clucth lever free play .........6-12
Adjusting the engine idling speed .............6-9
Adjusting the rear brake light switch .......6-13
Adjusting the throttle cable free play .........6-9
BBattery......................................................6-19
Brake lever .................................................3-4
Brake pedal ................................................3-5
CCare............................................................7-1
Cast wheels .............................................6-12
Catalytic converter .....................................3-6
Clucht lever ................................................3-4
Controls and instruments ..........................2-3
Changing the brake fluid..........................6-15
Checking and lubricating the brake and
cluctch levers.........................................6-18
Checking and lubricating the brake
and shift pedals .....................................6-17
Checking and lubricating the cables .......6-17
Checking and lubricating the sidestand ..6-18
Checking the brake fluid level .................6-14
Checking the front fork ............................6-18
Checking the spark plug ............................6-6
Checking the steering ..............................6-19
Checking the wheel bearings ..................6-19
D2-stroke engine oil ........................................3-6
Drive Chain slack........................................6-16
EEngine break-in ..........................................5-3
Engine overheating ..................................6-25
FFrame serial number ..................................9-1
Front brake pads......................................6-14
Fuel cock....................................................3-6
Fuel tank cap .............................................3-5
HHandlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ....................3-8
Indicator lights ...........................................3-1
KKey identification number ..........................9-1
LLeft view .....................................................2-1
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
OOwner’s tool kit ..........................................6-1
PParking .......................................................5-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear brake pads ......................................6-14
Removing and installing cowlings .............6-5
Replacing a turn signal light bulb or the
tail/brake light bulb ................................6-21Replacing the fuse ...................................6-20
Replacing the headlight bulb ...................6-21
Replacing the license plate light bulb......6-22
Right view ..................................................2-2
SSeat ............................................................3-7
Shift pedal ..................................................3-4
Shifting .......................................................5-2
Sidestand ...................................................3-8
Speedometer unit ......................................3-2
Starter (choke) lever ...................................3-7
Starting a cold engine ................................5-1
Storage.......................................................7-2
Storage compartment ................................3-7
Supporting the mortorcycle .....................6-22
TTachometer ................................................3-3
Tips for reducing fuel consumption ...........5-2
Tires .........................................................6-10
To check the coolant level .........................6-8
Transmission oil .........................................6-6
Troubleshooting .......................................6-23
Troubleshooting charts ............................6-24
INDEX
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 66