engine oil YAMAHA VERSITY 300 2004 User Guide

PERIODIC MAINTENANCE AND MINOR REPAIR
6CAUTION:
1. Engine oil drain bolt
2. Washer
6-15
12ZAUM0129
4. Check the washer for damage and
replace it if necessary.
5. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m
•kgf)
NOTE :
Make sure that the washer is properly
seated.6. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil filler
cap.
Recommended engine oil:
See page 8-1.
Oil quantity:
Periodic oil change:
1.2 L
Total amount (dry engine):
1.4 L7. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
8. Reset the oil change indicator.
(See page 3-7 for details.)
ECA00140
•Do not use oils with a diesel
specification of "CD" or oils of a
higher quality than specified. In
addition, do not use oils labeled
"ENERGY CONSERVING II" or
higher.
•Be sure no foreign material
enters the crankcase.

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU04228
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several mi-
nutes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
Tightening torque:
Final transmission oil drain bolt:
22 Nm (2.2 m
•kgf)
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
1. Final transmission oil filler cap1. Final transmission oil drain bolt
Recommended final transmission
oil:
See page 8-2.
Oil quantity:
0.25 L
EWA00062
•Make sure that no foreign
material enters the final trans-
mission case.
•Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
WARNING
6-16
1
ZAUM0441
11
ZAUM0442

PERIODIC MAINTENANCE AND MINOR REPAIR
63. Pull the sponge material out along
with the mesh sheet, clean it with
solvent, and then squeeze the
remaining solvent out.
4. Check the sponge material for
damage and replace it if
necessary.
5. Allow the sponge material to dry.
6. Apply oil of the recommended
type to the entire surface of the
sponge material, and then
squeeze the excess oil out.
NOTE :
The sponge material should be wet but
not dripping.
Recommended oil:
Engine oil
7. Insert the sponge material into the
air filter case.
8. Install the air filter case cover by
installing the screws.
Cleaning the V-belt case air filter
element
1. Remove the V-belt case air filter
cover by removing the screws.
1. V-belt case air filter cover
2. Screw (x3)
6-19
ZAUM0447
21
ZAUM0448

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU02962
Checking and lubricating the
cables
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the cables
and cable ends should be lubricated if
necessary. If a cable is damaged or does
not move smoothly, have a Yamaha dea-
ler check or replace it.
Recommended lubricant:
Engine oil
EW000112
Damage to the outer sheath may
interfere with proper cable operation
and will cause the inner cable to rust.
Replace a damaged cable as soon
as possible to prevent unsafe con-
ditions.
WARNING
EAU04034
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated or
replaced at the intervals specified in the
periodic maintenance chart.
EAU03118
Lubricating the front and
rear brake levers
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic main-
tenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
6-26
ZAUM0061

SCOOTER CARE AND STORAGE
7
Care
While the open design of a scooter
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality
components are used. A rusty exhaust
pipe may go unnoticed on a car,
however, it detracts from the overall
appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.CleaningECA00011
•Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
•Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
CAUTION:
7-1

SCOOTER CARE AND STORAGE
7 Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
"Care" section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
4. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark
plug cap.
EWA00003
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
5. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to
prevent the tires from becoming
degraded in one spot.
WARNING
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an
excessively cold or warm place
(less than 0 °C or more than 30
°C). For more information on
storing the battery, see page
6-30.
NOTE :
Make any necessary repairs before
storing the scooter.
7-4

SPECIFICATIONS
8
Model VP300
Dimensions:
Overall length 2,170 mm
Overall width 765 mm
Overall height 1,465 mm
Seat height 805 mm
Wheelbase 1,480 mm
Minimum ground clearance 155 mm
Minimum turning radius 1,706 mm
Weight:
Wet (with oil and a full fuel tank) 174 kg
Engine:
Engine type Liquid cooled, 4 strokes SOHC
Cylinder arrangementSingle cylinder, Forward inclined
Displacement 264 cm
3
Bore x stroke 71.0 x 66.8
Compression ratio 10:1
Starting system type Electric starter
Lubrication system Wet sump
Specifications
Engine oil:
Type
-20°-10°10°20°30°40°50°C
0°
SAE 10W/30
SAE 10W/40
SAE 15W/40
SAE 20W/40
SAE 20W/50
Recommended engine oil API Service SE, SF, SG type
Classification or higher
CAUTION:
8-1
Be sure to use motor oils that do not contain anti-fric-
tion modifiers. Passenger car motor oils (often labeled
“Energy Conserving II”) contain anti-friction additives
which will cause clutch and/or starter cluth slippage,
resulting in reduced component life and poor engine
performance.
Quantity
Periodic oil change 1.2 L
Total amount (dry engine) 1.4 L

SPECIFICATIONS
8
Transmission oil:
Type Engine oil SAE 10W30
(API SE)
Total amount 0.25L
Coolant system capacity:
(including all routes)1.6L
Air filter:Wet type element.
Fuel:
Recommended fuel REGULAR UNLEADED
GASOLINE ONLY
Fuel tank capacity 10.9L
Carburetor:
Type / quantity TK5SE x 1
Manufacturer TK
Spark plug:
Type / Manufacturer DR8EA / NGK
Spark plug gap 0.6—0.7 mm
Clutch type:Dry, centrifugal automatic
Transmission:
Primary reduction system Helical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 37/12 (3.083)
Transmission type V-belt automatic
Operation Centrifugal automatic typeChassis:
Frame type Steel tube underbone
Caster angle ((degree)) 26°
Trail 90 mm
Tires:
Front:
Type Tubeless
Size 120/80-14 58P
Manufacturer / Model MICHELIN / PILOT CITY TL
Rear:
Type Tubeless
Size 150/70-14 66P
Manufacturer / Model MICHELIN / PILOT CITY TL
Maximum load * 202 Kg
Air pressure (cold tire):
Up to 90 kg load*
Front 180 kpa (1.8 kgf/cm
2, 1.8 Bar)
Rear 190 kpa (1.9 kgf/cm2, 1.9 Bar)
90 kg load — 160 kg load *
Front 180 kpa (1.8 kgf/cm
2, 1.8 Bar)
Rear 200 kpa (2.0 kgf/cm2, 2.0 Bar)
160 kg load — maximum
load *
Front 190 kpa (1.9 kgf/cm
2, 1.9 Bar)
Rear 220 kpa (2.2 kgf/cm2, 2.2 Bar)
* Total weight of rider, passenger, cargo and accessories.
8-2

INDEX
A
Acceleration and deceleration ............. 5-3
Air filter and V-belt case air filter
elements, cleaning ....................... 6-18
Anti-theft alarm (optional) ................... 3-7
Auxiliary DC jack ............................... 3-18
Anti-theft device housing ................... 3-14
B
Battery .............................................. 6-29
Battery voltage / coolant
temperature gauge ......................... 3-3
Brake fuid level, checking ................. 6-24
Brake fluid, changing ........................ 6-25
Bake lever, front .................................. 3-9
Brake lever, rear .................................. 3-9
Brake levers, lubricating .................... 6-26
Brake pads, checking ........................ 6-24Braking ................................................ 5-3
C
Cables, checking and lubricating ...... 6-26
Carburator, adjusting ......................... 6-20
Care .................................................... 7-1
Catalytic converter ............................ 3-11
Centerstand and sidestand, checking
and lubricating .............................. 6-27
Conversion table ................................. 8-4
Coolant .............................................. 6-17
Cowlings and panels, removing
and installing .................................. 6-5
E
Engine break-in ................................... 5-4
Engine oil .......................................... 6-13
F
Final transmission oil ........................ 6-16
Front and rear brake lever free play,
adjusting ....................................... 6-23
Front fork, checking ........................... 6-27
Fuel ................................................... 3-10
Fuel consumption, tips for reducing .... 5-4
Fuel gauge .......................................... 3-3
Fuel tank cap .................................... 3-10Fuses, replacing ................................ 6-30
H
Handlebar switches ............................. 3-8
Dimmer switch ............................... 3-8
Engine stop switch ......................... 3-8
Horn switch .................................... 3-8
Hazard switch ................................ 3-9
Pass switch .................................... 3-8
Start switch .................................... 3-8
Turn signal switch ........................... 3-8
Headlight bulb, replacing ................... 6-32
I
Identification number ........................... 9-1
Ignition circuit cut-off system ............. 3-16
Indicator lights ..................................... 3-2
High beam indicator light ............... 3-2
Low beam indicator light ................ 3-2
Turn signal indicator lights .............. 3-2
K
Key identification number .................... 9-1
L
License plate liht bulb, replacing ....... 6-35