key YAMAHA VERSITY 300 2004 User Guide

INSTRUMENT AND CONTROL FUNCTIONS
3
1. Auxiliary DC jack
EAUM0102*
Auxiliary DC jack
This scooter is equipped with an
auxiliary DC jack in the storage
compartment A.
12-V accessories connected to the
auxiliary jack can be used when the key
is in the "
" position and should only
be used when the engine is running.
EC000028*
The accessories connected to the
auxiliary DC jack should not be used
with the engine turned off, and their
combined load must never exceed
2.5 A or 30 W, otherwise the battery
may discharge.
To use the auxiliary DC jack
1. Turn the key to "
".
2. Remove the dust cap from the
receptacle.
3. Insert the accessory plug into the
receptacle.
4. Turn the key to "
", and then start
the engine. (See page 5-1 for
details.)
5. When the accessory jack is not
being used, make sure that the
dust cap is installed onto the
receptacle for protection.
CAUTION:
12V
1
ZAUM0417
3-18

OPERATION AND IMPORTANT RIDING POINTS
5
EAU01118
EW000129
•Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or
function that you do not
thoroughly understand.
•Never start the engine or
operate it in a closed area for
any length of time. Exhaust fu-
mes are poisonous, and
inhaling them can cause loss of
consciousness and death
within a short time. Always
make sure that there is
adequate ventilation.
•For safety, always start the
engine with the centerstand
down.
WARNING
EAU03843
Starting the engine
See page 5-4 for engine break-in ins-
tructions prior to operating the
vehicle for the first time.
In order for the ignition circuit cut-off
system to enable starting, the sidestand
must be up.
EW000054
•Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-16.
•Never ride with the sidestand
down.1. Turn the key to "
" and make
sure that the engine stop switch
is set to "
".
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the
front or rear brake.
CAUTION:
WARNING
1234
ZAUM0418
1. Rear brake lever
2. Engine stop switch
3. Start switch
4. Front brake lever
5-1

OPERATION AND IMPORTANT RIDING POINTS
5
EAU00461
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EW000058
•Since the engine and exhaust
system can become very hot,
park in a place where
pedestrians or children are not
likely to touch them.
•Do not park on a slope or on
soft ground, otherwise the
scooter may overturn.
EC000062
Never park in an area where there
are fire hazards such as grass or
other flammable materials.
WARNING
CAUTION:
5-5

PERIODIC MAINTENANCE AND MINOR REPAIR
6
1. Backup fuse
2. Headlight fuse
3. Radiator fan fuse
4. Signaling system fuse
5. Ignition fuse
6. Auxiliary DC jack fuse
7. Spare fuse (x2)
8. Fuse tongs
CAUTION:
6-31
12345 776
8
ZAUM0460
The fuse block, which contains the fu-
ses for the individual circuits, is located
in the storage compartment A. (See
page 3-12 for storage compartment
opening and closing procedures.)If a fuse is blown, replace it as follows.
1. Turn the key to "
" and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
Specified fuses:
Main fuse Box
Main fuse: 30 A
Fuse block
Backup fuse 3 A
Headlight fuse: 15 A
Radiator fan fuse: 15 A
Signaling system fuse: 15 A
Ignition fuse: 7.5 A
Auxiliary DC jack fuse: 3 A3. Turn the key to "
" and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
EC000103
Do not use a fuse of a higher
amperage rating than recommended
to avoid causing extensive damage
to the electrical system and possibly
a fire.

9
EAU01039
CONSUMER INFORMATION
Identification numbers ......................................................................... 9-1
Key identification number .................................................................... 9-1
Vehicle identification number .............................................................. 9-1
Model label .......................................................................................... 9-2

CONSUMER INFORMATION
9
EAU02944
Identification numbers
Record the key identification number,
vehicle identification number and model
label information in the spaces provided
below for assistance when ordering
spare parts from a Yamaha dealer or
for reference in case the vehicle is
stolen.
1. KEY IDENTIFICATION NUMBER:
2. VEHICLE IDENTIFICATION
NUMBER:
3. MODEL LABEL INFORMATION:
EAU01041
Key identification number
The key identification number is
stamped into the key tag.
Record this number in the space
provided and use it for reference when
ordering a new key.
EAU01044*
Vehicle identification number
The vehicle identification number is
stamped into the frame behind the
panel D.
(See page 6-10 for panel removal and
installation procedures.)
NOTE :
The vehicle identification number is
used to identify your scooter and may
be used to register your scooter with
the licensing authority in your area.
9-1
1
ZAUM0070
1. Key identification number
x
xxxxxxxxx
1
ZAUM0468
1. Vehicle identification number

INDEX
A
Acceleration and deceleration ............. 5-3
Air filter and V-belt case air filter
elements, cleaning ....................... 6-18
Anti-theft alarm (optional) ................... 3-7
Auxiliary DC jack ............................... 3-18
Anti-theft device housing ................... 3-14
B
Battery .............................................. 6-29
Battery voltage / coolant
temperature gauge ......................... 3-3
Brake fuid level, checking ................. 6-24
Brake fluid, changing ........................ 6-25
Bake lever, front .................................. 3-9
Brake lever, rear .................................. 3-9
Brake levers, lubricating .................... 6-26
Brake pads, checking ........................ 6-24Braking ................................................ 5-3
C
Cables, checking and lubricating ...... 6-26
Carburator, adjusting ......................... 6-20
Care .................................................... 7-1
Catalytic converter ............................ 3-11
Centerstand and sidestand, checking
and lubricating .............................. 6-27
Conversion table ................................. 8-4
Coolant .............................................. 6-17
Cowlings and panels, removing
and installing .................................. 6-5
E
Engine break-in ................................... 5-4
Engine oil .......................................... 6-13
F
Final transmission oil ........................ 6-16
Front and rear brake lever free play,
adjusting ....................................... 6-23
Front fork, checking ........................... 6-27
Fuel ................................................... 3-10
Fuel consumption, tips for reducing .... 5-4
Fuel gauge .......................................... 3-3
Fuel tank cap .................................... 3-10Fuses, replacing ................................ 6-30
H
Handlebar switches ............................. 3-8
Dimmer switch ............................... 3-8
Engine stop switch ......................... 3-8
Horn switch .................................... 3-8
Hazard switch ................................ 3-9
Pass switch .................................... 3-8
Start switch .................................... 3-8
Turn signal switch ........................... 3-8
Headlight bulb, replacing ................... 6-32
I
Identification number ........................... 9-1
Ignition circuit cut-off system ............. 3-16
Indicator lights ..................................... 3-2
High beam indicator light ............... 3-2
Low beam indicator light ................ 3-2
Turn signal indicator lights .............. 3-2
K
Key identification number .................... 9-1
L
License plate liht bulb, replacing ....... 6-35