brake YAMAHA VERSITY 300 2004 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: VERSITY 300, Model: YAMAHA VERSITY 300 2004Pages: 104, PDF Size: 2.82 MB
Page 11 of 104
GIVE SAFETY THE RIGHT OF WAY
1
EAU03099
Further safe-riding points
•Be sure to signal clearly when making turns.
•Braking can be extremely difficult on a wet road. Avoid hard braking, because the scooter could slide.
Apply the brakes slowly when stopping on a wet surface.
•Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
•Be careful when passing parked cars. A driver might not see you and open a door in your path.
•Railroad crossings, streetcar rails, iron plates on road construction sites, and manhole covers become
extremely slippery when wet. Slow down and cross them with caution. Keep the scooter upright, otherwise
it could slide out from under you.
•The brake pads could get wet when you wash the scooter. After washing the scooter, check the brakes
before riding.
•Always wear a helmet, gloves, trousers (tapered around the cuff and ankle so they do not flap), and a
bright colored jacket.
•Do not carry too much luggage on the scooter. An overloaded scooter is unstable.
1-2
Page 15 of 104
2
DESCRIPTION
Right view
7. Grab bar (Page 5-2)
8. Fuel tank cap (Page 3-10)
9. Battery (Page 6-29)
10. Coolant reservoir cap (Page 6-17)
11. Front brake pads (page 6-24)12. Main fuse box (page 6-30)
13. Engine oil filler cap (page 6-13)
14. Centerstand (page 6-27)
15. Rear brake pads (page 6-24)
7
15 14 13 12 118910
2-2
Page 16 of 104
2
DESCRIPTION
Controls and instruments
PUSHOPEN
16 17 18 19 20 21 22 2423
25 26
16. Rear brake lever (Page 3-9, 6-26)
17. Left handlebar switches (Page 3-8)
18. Front storage compartment B (Page 3-13)
19. Speedometer/
multi-function display(page 3-2)
20. Luggage hook (page 3-15)21. Main switch/steering lock (page 3-1)
22. Right handlebar switches (page 3-8)
23. Throttle grip (page 6-20, 6-26)
24. Front brake lever (page 3-9, 6-26)
25. Front storage compartment A (page 3-12)
26. Fuse box (page 6-30)
2-3
Page 17 of 104
EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
Main switch/steering lock .................................................................... 3-1
Indicator lights ..................................................................................... 3-2
Speedometer ...................................................................................... 3-2
Fuel gauge .......................................................................................... 3-3
Battery voltage/coolant temperature gauge ........................................ 3-3
Multi-function display .......................................................................... 3-4
Anti-theft alarm (optional) .................................................................... 3-7
Handlebar switches ............................................................................. 3-8
Front brake lever ................................................................................. 3-9
Rear brake lever .................................................................................. 3-9
Fuel tank cap .................................................................................... 3-10
Fuel ................................................................................................... 3-10
Catalytic converter ............................................................................ 3-11
Seat ................................................................................................... 3-12
Storage compartments ...................................................................... 3-12
Anti-theft device housing ................................................................... 3-14
Adjusting the shock absorber assemblies ......................................... 3-14
Luggage hook ................................................................................... 3-15
Sidestand .......................................................................................... 3-16
Ignition circuit cut-off system ............................................................. 3-16
Auxiliary DC jack ............................................................................... 3-18
3
Page 25 of 104
INSTRUMENT AND CONTROL FUNCTIONS
3
1
2
3
4ZAUM0407
1. Pass switch ""
2. Dimmer switch "
/ "
3. Turn signal switch "
/ "
4. Horn switch "
"
EAU00118
Handlebar switches
EAU00119
Pass switch ""
Press this switch to flash the headlight.
EAU03888
Dimmer switch " / "
Set this switch to "
" for the high beam
and to "
" for the low beam.
EAU03889
Turn signal switch " / "
To signal a right-hand turn, push this
switch to "
". To signal a left-hand
turn, push this switch to "
". When
released, the switch returns to the
center position. To cancel the turn si-
gnal lights, push the switch in after it
has returned to the center position.
EAU00129
Horn switch ""
Press this switch to sound the horn.
1
2
3
ZAUM0408
1. Engine stop switch " / "
2. Hazard switch "
/ "
3. Start switch "
"
EAU03890
Engine stop switch " / "
Set this switch to "
" before starting the
engine. Set this switch to "
" to stop
the engine in case of an emergency,
such as when the scooter overturns or
when the throttle cable is stuck.
3-8
EAU03801
Start switch ""
With the sidestand up, push this switch
while applying the front or rear brake
to crank the engine with the starter.
EC000005
See page 5-1 for starting instruc-
tions prior to starting the engine.
CAUTION:
Page 26 of 104
3
INSTRUMENT AND CONTROL FUNCTIONS
CAUTION:
1
ZAUM0084
1
ZAUM0085
EAU03882
Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the
handlebar grip.
EAU00163
Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the
handlebar grip.
1. Front brake lever
1. Rear brake lever
3-9
EC000006
Do not use the hazard light for an
extended length of time, otherwise
the battery may discharge.
EAUM0111
Hazard switch "", ""
With the key in the "
" position, set this
switch to "
" to turn on the hazard
lighting (simultaneous flashing of all turn
signal lights). To turn off the hazard
lighting, set this switch to "
" and, then
turn the key to "
".
NOTE :
Even if the key is turned from "
" to
"
" with the hazard lighting on, the
hazard lighting will continue to flash
regardless of the hazard switch position.
To cancel the hazard lighting, the key
must be turned to "
" and the hazard
switch must be set to the "" position.
The hazard lighting is used in case of
an emergency or to warn other drivers
when your scooter is stopped where it
might be a traffic hazard.
Page 33 of 104
INSTRUMENT AND CONTROL FUNCTIONS
3
1
ZAUM0416
EAU00330
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
scooter upright.
NOTE :
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation
of the ignition circuit cut-off system.)
EW000044
The scooter must not be ridden with
the sidestand down, or if the
sidestand cannot be properly moved
up (or does not stay up), otherwise
the sidestand could contact the
ground and distract the operator,
resulting in a possible loss of
control. Yamaha’s ignition circuit cut-
off system has been designed to
assist the operator in fulfilling the
responsibility of raising the
sidestand before starting off.
Therefore, check this system
regularly as described below and
have a Yamaha dealer repair it if it
does not function properly.
1. Sidestand switch
WARNINGEAU00337
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch and
brake light switches) has the following
functions.
•It prevents starting when the
sidestand is up, but neither brake
is applied.
•It prevents starting when either
brake is applied, but the sidestand
is still down.
•It cuts the running engine when
the sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
EW000045
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
WARNING
3-16
Page 34 of 104
3
INSTRUMENT AND CONTROL FUNCTIONS
The sidestand switch may be defective.
The scooter should not be ridden until
checked by a Yamaha dealer.
YES NO
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to .
3. Turn the key to .
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
The brake switch may be defective.
The scooter should not be ridden until
checked by a Yamaha dealer.
With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.
Does the engine start?
With the engine still running:
9. Move the sidestand down.
Does the engine stall?
The sidestand switch may be defective.
The scooter should not be ridden until
checked by a Yamaha dealer.
NOTE:
This check is most reliable if performed with
a warmed-up engine.
YES NO
The system is OK. The scooter can be ridden.
YES NO
3-17
Page 38 of 104
PRE-OPERATION CHECKS
4The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or
loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual
inspection, to check the following points before each ride.
EAU03439
Pre-operation check list
ITEM CHECKS PAGE
•Check fuel level in fuel tank.
Fuel•Refuel if necessary. 3-3 — 3-4, 3-10 — 3-11
•Check fuel line for leakage.
•Check oil level in engine.
Engine oil•If necessary, add recommended oil to specified level. 6-13 — 6-15
•Check vehicle for oil leakage.
Final transmission oil•Check vehicle for oil leakage. 6-16
•Check coolant level in reservoir.
Coolant•If necessary, add recommended coolant to specified level. 6-17
•Check cooling system for leakage.
•Check operation.
•If soft or spongy, have Yamaha dealer bleed hydraulic system.
Front brake•Check fluid level in reservoir. 3-9, 6-23 — 6-25
•If necessary, add recommended brake fluid to specified level.
•Check hydraulic system for leakage.
•Check operation.
•If soft or spongy, have Yamaha dealer bleed hydraulic system.
Rear brake•Check fluid level in reservoir. 3-9, 6-23 — 6-25
•If necessary, add recommended brake fluid to specified level.
•Check hydraulic system for leakage.
4-1
Page 39 of 104
4
PRE-OPERATION CHECKS
ITEM CHECKS PAGE
•Make sure that operation is smooth.
Throttle grip•Check cable free play.
6-20, 6-26
•If necessary, have Yamaha dealer adjust cable free play
and lubricate cable and grip housing.
•Check for damage.
Wheels and tires•Check tire condition and tread depth.
6-21 — 6-23
•Check air pressure.
•Correct if necessary.
Brake levers•Make sure that operation is smooth.
3-9, 6-23, 6-26
•Lubricate lever pivoting points if necessary.
Centerstand, sidestand•Make sure that operation is smooth.
6-27
•Lubricate pivots if necessary.
Chassis fasteners•Make sure that all nuts, bolts and screws are properly tightened.
—
•Tighten if necessary.
Instruments, lights•Check operation.
3-1 — 3-8, 6-32 — 6-35
signals and switches•Correct if necessary.
Sidestand switch•Check operation of ignition circuit cut-off system.
3-16
•If system is defective, have Yamaha dealer check vehicule.
4-2