brake YAMAHA VMAX 2009 Owner's Manual

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
1
2
3
4
5
6
7
8
9

EAU24181
Tail/brake light
This model is equipped with an
LED-type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
EAU24204
Replacing a turn signal light
bulb
1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
NOTICE:
Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]

1. Screw
2. Turn signal light lens
1
2

1. Turn signal light bulb
1

MOTORCYCLE CARE AND STORAGE
7-2
2
3
4
5
6
78
9 plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.TIP

Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE:
Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]

2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces (except the tita-
nium mufflers) to prevent
corrosion.
Cleaning the titanium mufflers
This model is equipped with titanium
mufflers, which require the following
special care.


Use only a soft, clean cloth or
sponge with mild detergent and
water to clean the titanium muf-
flers. However, if the mufflers can-
not be thoroughly cleaned with
mild detergent, alkaline products
and a soft brush may be used.

Never use compounds or other
special treatments to clean the tita-
nium mufflers, as they will remove

MOTORCYCLE CARE AND STORAGE
7-3
1
2
3
4
5
6
7
8
9
the finish on the outer surface of
the mufflers.


Even the smallest amounts of oil,
such as from oily towels or finger-
prints, will leave stains on the tita-
nium mufflers, which can be
removed with a mild detergent.

Note that the thermally induced
discoloring of the portion of the ex-
haust pipe leading into the titanium
mufflers is normal and cannot be
removed.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts.
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing or covering it.
WARNING

EWA11131
Contaminants on the brakes or tires
can cause loss of control.

Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
NOTICE

ECA10800

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, buttreat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP


Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.

SPECIFICATIONS
8-2
2
3
4
5
6
7
89 Transmission:

Primary reduction system:
Spur gear
Primary reduction ratio:
86/57 (1.509)
Secondary reduction system:
Shaft drive
Secondary reduction ratio:
22/23
×
29/09 (3.082)
Transmission type:
Constant mesh 5-speed
Operation:
Left foot operation
Gear ratio:
1st:
38/16 (2.375)
2nd:
38/21 (1.810)
3rd:
35/25 (1.400)
4th:
29/26 (1.115)
5th:
29/31 (0.935)
Chassis:
Frame type:
Diamond
Caster angle:
31.00 °
Trail:
148.0 mm (5.83 in)
Front tire:
Type:
Tubeless
Size:
120/70R18M/C 59V
Manufacturer/model:
BRIDGESTONE/BT028F
Rear tire:
Type:
Tubeless
Size:
200/50R18M/C 76V
Manufacturer/model:
BRIDGESTONE/BT028R
Loading:
Maximum load:
190 kg (419 lb)
(Total weight of rider, passenger, cargo and
accessories)
Tire air pressure (measured on cold
tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
250 kPa (2.50 kgf/cm
2

, 36 psi)
Rear:
290 kPa (2.90 kgf/cm
2

, 42 psi)
Loading condition:
90–190 kg (198–419 lb)
Front:
250 kPa (2.50 kgf/cm
2

, 36 psi)Rear:
290 kPa (2.90 kgf/cm
2

, 42 psi)
High-speed riding:
Front:
290 kPa (2.90 kgf/cm
2

, 42 psi)
Rear:
290 kPa (2.90 kgf/cm
2

, 42 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
18M/C x MT3.50
Rear wheel:
Wheel type:
Cast wheel
Rim size:
18M/C x MT6.00
Front brake:
Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4

SPECIFICATIONS
8-3
1
2
3
4
5
6
7
8
9Front suspension:

Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)
Rear suspension:
Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
110.0 mm (4.33 in)
Electrical system:
Ignition system:
TCI (digital)
Charging system:
AC magneto
Battery:
Model:
YTZ14S
Voltage, capacity:
12 V, 11.2 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage
×
quantity:
Headlight:
12 V, 60 W/55.0 W
×
1
Tail/brake light:
LEDFront turn signal light:
12 V, 10.0 W
×
2
Rear turn signal light:
12 V, 10.0 W
×
2
Auxiliary light:
12 V, 5.0 W
×
1
Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Oil level warning light:
LED
Turn signal indicator light:
LED x 2
Fuel level warning light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
ABS warning light:
LED
Immobilizer system indicator light:
LED

Fuses:
Main fuse:
50.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
7.5 AIgnition fuse:
20.0 A
Parking lighting fuse:
7.5 A
Radiator fan fuse:
20.0 A
Fuel injection system fuse:
15.0 A
ABS control unit fuse:
7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse:
7.5 A
Electronic throttle valve fuse:
7.5 A

INDEX
A
ABS ......................................................... 3-18
ABS warning light ...................................... 3-5
Air filter element....................................... 6-17
Anti-theft alarm (optional) ........................ 3-14
Auxiliary light bulb, replacing ................... 6-36
B
Battery ..................................................... 6-28
Brake and clutch fluids, changing ............ 6-24
Brake and clutch levers, checking and
lubricating .............................................. 6-25
Brake fluid level, checking ....................... 6-23
Brake lever .............................................. 3-17
Brake pedal ............................................. 3-18
Brake pedal, checking and lubricating ..... 6-25
C
Cables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converters ................................. 3-22
Clutch lever.................................... 3-16
,
6-21
Coolant .................................................... 6-14
Coolant temperature warning light............. 3-4
Cowling and panels, removing and
installing .................................................. 6-6
D
Dimmer switch ......................................... 3-15
E
Engine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-17
Engine oil and oil filter cartridge ................ 6-9
Engine stop switch................................... 3-15
Engine trouble warning light ...................... 3-4
EXUP system .......................................... 3-28
F
Final gear oil ............................................ 6-12
Front and rear brake pads, checking....... 6-22
Front brake lever free play, checking ...... 6-21
Front fork, adjusting................................. 3-24
Front fork, checking ................................. 6-26
Fuel ......................................................... 3-20
Fuel level warning light .............................. 3-4
Fuel tank cap ........................................... 3-19
Fuses, replacing ...................................... 6-31
H
Handlebar switches ................................. 3-15
Hazard switch .......................................... 3-16
Headlight bulb, replacing ......................... 6-32
High beam indicator light ........................... 3-3
Horn switch.............................................. 3-15
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-29
Immobilizer system.................................... 3-1
Immobilizer system indicator light ............. 3-5
Indicator and warning lights....................... 3-3
K
Key identification number .......................... 9-1
L
License plate light bulb, replacing ........... 6-35
Luggage strap holders............................. 3-28
M
Main switch/steering lock .......................... 3-2
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function display ................................. 3-6
N
Neutral indicator light................................. 3-3
O
Oil level warning light ................................ 3-3
P
Parking ...................................................... 5-3
Part locations ............................................ 2-1
Pass switch ............................................. 3-15
Periodic maintenance and lubrication
chart ........................................................ 6-2
R
Rear brake light switch, adjusting ........... 6-22
S
Safety information ..................................... 1-1
Seats ....................................................... 3-22
Shifting ...................................................... 5-2
Shift pedal ............................................... 3-17
Shift pedal, checking and lubricating ...... 6-26
Shock absorber assembly, adjusting ...... 3-26
Sidestand ................................................ 3-29
Sidestand, checking and lubricating ....... 6-26
Spark plugs, checking ............................... 6-8
Specifications ............................................ 8-1
Speedometer unit...................................... 3-5
Starting the engine .................................... 5-1
Start switch ............................................. 3-15
Steering, checking .................................. 6-27
Storage ..................................................... 7-4
Supporting the motorcycle ...................... 6-36
T
Tail/brake light......................................... 6-34
Throttle cable free play, checking ........... 6-17
Throttle grip and cable, checking and
lubricating ............................................. 6-24
Tires ........................................................ 6-18
Tool kit ...................................................... 6-1