ECO mode YAMAHA VX 2008 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2008, Model line: VX, Model: YAMAHA VX 2008Pages: 94, PDF Size: 6.83 MB
Page 6 of 94
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Craft Identification Number (CIN) ...... 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 7
Safety information ............................. 9
Limitations on who may operate
the watercraft .............................. 9
Cruising limitations ....................... 10
Operation requirements ............... 11
Recommended equipment ........... 13
Hazard information ....................... 14
Watercraft characteristics ............. 14
Water-skiing ................................. 16
Safe boating rules ........................ 17
Enjoy your watercraft
responsibly ................................ 18
Features and functions ................... 19
Location of main components ...... 19
Operation of controls and other
functions .................................... 23
Seat ................................................. 23
Hood ................................................ 23
Fuel tank filler cap ........................... 24
Remote control transmitter
(for VX Deluxe/VX Cruiser) .......... 24
Engine stop switch .......................... 25
Engine shut-off switch ..................... 25
Start switch ...................................... 26
Throttle lever ................................... 26
Cooling water pilot outlet ................. 26
Steering system ............................... 27
Shift lever (for VX Deluxe/
VX Cruiser) .................................. 27
Handgrip .......................................... 28Bow eye ........................................... 28
Stern eyes ....................................... 28
Yamaha Engine Management
System (YEMS) ........................... 28
Yamaha Security System and
low-RPM mode (for VX Deluxe/
VX Cruiser) .................................. 29
Multifunction information center ...... 30
Storage compartments .................... 35
Operation ......................................... 38
Fuel and oil .................................. 38
Gasoline .......................................... 38
Engine oil ......................................... 39
Filling the fuel tank .......................... 39
Pre-operation checks ................... 40
Pre-operation check list ................... 40
Pre-operation check points .............. 42
Operation ..................................... 49
Engine break-in ............................... 49
Launching the watercraft ................. 49
Starting the engine .......................... 49
Stopping the engine ........................ 51
Leaving the watercraft ..................... 51
Operating your watercraft ............ 52
Getting to know your watercraft ....... 52
Learning to operate your
watercraft ..................................... 52
Riding with passengers ................... 53
Starting the watercraft ..................... 53
Boarding and starting in deep
water ............................................ 54
Capsized watercraft ......................... 57
Turning the watercraft ..................... 58
Stopping the watercraft ................... 60
Beaching the watercraft ................... 60
Docking the watercraft ..................... 60
Reverse on waterways
(for VX Deluxe/VX Cruiser) .......... 60
Rough water operation .................... 61
UF1K73E0.book Page 1 Wednesday, July 11, 2007 9:15 AM
Page 8 of 94
General and important labels
1
EJU36450
Identification numbers
Record the Primary Identification (PRI-ID)
number, Craft Identification Number (CIN),
and engine serial number in the spaces pro-
vided for assistance when ordering spare
parts from a Yamaha dealer. Also record and
keep these ID numbers in a separate place in
case your watercraft is stolen.
EJU30281Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a plate at-
tached inside the engine compartment.
MODEL:
VX1100-G (VX)
VX1100B-G (VX Deluxe)
VX1100A-G (VX Cruiser)
EJU36550Craft Identification Number (CIN)
The CIN is stamped on a plate attached to the
aft deck.
EJU30310Engine serial number
The engine serial number is stamped on a
plate attached to the engine unit.
1Primary Identification (PRI-ID) number loca-
tion
1Craft Identification Number (CIN) location
1Engine serial number location
UF1K73E0.book Page 1 Wednesday, July 11, 2007 9:15 AM
Page 33 of 94
Features and functions
26
EJU31191Start switch
Push the start switch (green button) to start
the engine.
NOTE:
The engine will not start when the lock mode
of the Yamaha Security System has been se-
lected (for VX Deluxe/VX Cruiser), the clip is
removed from the engine shut-off switch, or
the throttle lever is squeezed. (See page 29
for Yamaha Security System lock and unlock
mode selection procedures.)
EJU31210Throttle lever
Squeeze the throttle lever to increase engine
speed.
Release the throttle lever to decrease engine
speed or to return it to the idle position.
EJU35971Cooling water pilot outlet
This watercraft is equipped with a cooling wa-
ter pilot outlet.
When the engine is running, cooling water is
circulated in the engine, and then it is dis-
charged from the pilot outlet.
To check for proper operation of the cooling
system, check that water is being discharged
from the pilot outlet. If water is not being dis-
charged from the outlet, cooling water may
not be circulating in the engine. When this oc-
curs, stop the engine and check for the cause.
(See pages 33 and 80 for more information.)
NOTE:
If the cooling water passages are dry, it will
take about 60 seconds for the water to
reach the outlet after the engine is started.
Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
1Start switch
1Throttle lever
UF1K73E0.book Page 26 Wednesday, July 11, 2007 9:15 AM
Page 36 of 94
Features and functions
29
EJU31380Yamaha Security System and low-
RPM mode (for VX Deluxe/VX Cruiser)
This watercraft is equipped with a remote con-
trol transmitter that is used to select the secu-
rity system and low-RPM mode settings.
Since the watercraft is programmed to recog-
nize the internal code from this transmitter
only, the security system setting can only be
changed with this transmitter. If you lose the
remote control transmitter or it does not oper-
ate properly, contact a Yamaha dealer.
EJU31390Yamaha Security System
(for VX Deluxe/VX Cruiser)
The Yamaha Security System functions to
help prevent unauthorized use or theft of the
watercraft. The engine cannot be started if the
security system is in the lock mode. The en-
gine can only be started in the unlock mode.
EJU36102Yamaha Security System lock and unlock
modes (for VX Deluxe/VX Cruiser)
The lock and unlock modes of this system can
only be selected while the engine is stopped.
When the lock button on the remote control
transmitter is pressed, the beeper sounds
once. This indicates the lock mode is selected
and the engine cannot be started.
The “SECURITY” indicator light comes on
when the security system is in the unlockmode and goes off when the security system
is in the lock mode.
When the unlock button on the remote control
transmitter is pressed for a short time, the
beeper sounds two times for the normal mode
or three times for the low-RPM mode. The
“SECURITY” indicator light will come on and
the engine can be started. (See the items in
“Selecting the normal mode/low-RPM mode”
for operation mode information.)
1Lock button
1“SECURITY” indicator light
1Unlock button
Number
of beepsYamaha Security Sys-
tem modeEngine
can be
started
1 beep Lock NO
2 beepsUnlock
(normal mode)YES
3 beepsUnlock
(low-RPM mode)YES
UF1K73E0.book Page 29 Wednesday, July 11, 2007 9:15 AM
Page 37 of 94
Features and functions
30
EJU31412Selecting the normal mode/low-RPM
mode (for VX Deluxe/VX Cruiser)
The normal mode and low-RPM mode can
only be selected when the engine is stopped
in the unlock mode. Press the unlock button
on the remote control transmitter for more
than 4 seconds to switch between the normal
mode and the low-RPM mode.
Normal mode
If the beeper sounds twice, the normal mode
is activated.
The watercraft can be ridden normally.
Low-RPM mode
If the beeper sounds three times, the low-
RPM mode is activated and the “L-MODE” in-
dicator light comes on.
Maximum engine speed (r/min) in the low-
RPM mode is limited to approximately 90% of
the maximum engine speed in the normal
mode.
NOTE:
If neither the start switch nor the remote
control transmitter is operated within 25
seconds after the unlock button is pressed
to select the unlock mode, the multifunction
information center display and the “L-
MODE” indicator light will go off. If this oc-
curs, press the lock button on the transmit-
ter briefly to select the lock mode, press the
unlock button briefly to select the unlockmode, and then press the unlock button
again for more than 4 seconds to select the
normal mode or low-RPM mode.
While the engine is running, input from the
remote control transmitter is not received.
CAUTION:
ECJ00080
If the remote control transmitter does not
operate when its buttons are pressed, the
battery may be low. Have a Yamaha dealer
replace the battery.
EJU31452Multifunction information center
This meter contains the following functions for
help and convenience in operating the water-
craft.
1“L-MODE” indicator light1Tachometer
2Speedometer
3Hour meter/voltmeter
4Fuel level meter
5“L-MODE” indicator light (for VX Deluxe/VX
Cruiser)
6“WARNING” light
7Fuel level warning indicator
8Oil pressure warning indicator
9Engine overheat warning indicator
10Check engine warning indicator
11Select button
12“SECURITY” indicator light
(for VX Deluxe/VX Cruiser)
UF1K73E0.book Page 30 Wednesday, July 11, 2007 9:15 AM
Page 56 of 94
Operation
49
EJU32740
Operation
WARNING
EWJ00510
Before operating your watercraft, become
familiar with all of the controls. Consult a
Yamaha dealer about any control or func-
tion that you do not fully understand. Fail-
ure to understand how the controls work
could cause an accident or prevent you
from avoiding an accident.
CAUTION:
ECJ00460
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft.
EJU32781Engine break-in
The engine break-in period is essential to al-
low the various components of the engine to
wear and polish themselves to the correct op-
erating clearances. This ensures proper per-
formance and promotes longer component
life.
CAUTION:
ECJ00440
Be sure to check the engine oil level be-
fore operating the watercraft for the first
time. (See page 42 for engine oil checking
procedures.)
(1) Launch the watercraft and start the en-
gine. (See page 49 for engine starting
procedures.)
(2) For the first 5 minutes, run the engine at
trolling speed only. For the 30 minutes of
operation after that, keep the engine
speed below 5000 r/min. For the 1 hour of
operation after that, keep the engine
speed below 6500 r/min.
(3) Proceed with normal operation.
CAUTION:
ECJ00430
Failure to follow the engine break-in pro-
cedure could result in reduced engine life
or even severe engine damage.
EJU32811Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles around you.
If there are waves, someone should make
sure that the watercraft is not pushed into the
trailer after launching the watercraft.
For VX Deluxe/VX Cruiser:
Use the remote control transmitter to select
the unlock mode. (See page 29 for Yamaha
Security System and low-RPM mode selec-
tion procedures.)
After the watercraft is in the water, start the
engine. Shift into reverse and move the wa-
tercraft back slowly.
For VX:
After the watercraft is in the water, turn it
around so that the bow faces the direction
you wish to go. Start the engine, and then
slowly move away from the launching area.
EJU32851Starting the engine
WARNING
EWJ00560
Never start the engine or let it run for any
length of time in an enclosed area. Ex-
haust fumes contain carbon monoxide, a
UF1K73E0.book Page 49 Wednesday, July 11, 2007 9:15 AM
Page 58 of 94
Operation
51
(4) Push the start switch (green button), and
then release it as soon as the engine
starts to run.
NOTE:
The engine will not start if the throttle lever is
squeezed.
CAUTION:
ECJ00480
Never push the start switch while the en-
gine is running.
Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.
EJU32860Stopping the engine
To stop the engine, release the throttle lever,
and then push the engine stop switch (red
button).
WARNING
EWJ00600
You need throttle to steer. Shutting the en-
gine off can cause you to hit an obstacle
you are attempting to avoid. A collision
could result in severe injury or death.
EJU32890Leaving the watercraft
If leaving the watercraft, select the lock
mode of the Yamaha Security System (for
VX Deluxe/VX Cruiser) and remove the en-
gine shut-off cord to reduce the chance of
accidental starting or unauthorized use by
children or others. (See page 29 for
Yamaha Security System and low-RPM
mode selection procedures.)
UF1K73E0.book Page 51 Wednesday, July 11, 2007 9:15 AM
Page 85 of 94
Trouble recovery
78
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU34592Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Yamaha Se-
curity Sys-
tem (VX
Deluxe/VX
Cruiser)Lock mode selected Select unlock mode
29
Engine shut-
off switchClip not in place Install clip
25
Fuse Burned out Replace the fuse and
check wiring82
Battery Run down Recharge 74
Poor terminal con-
nectionsTighten as required
74
Terminal corroded Clean 65
Starter motor Faulty Have serviced by
Yamaha dealer—
Engine does not
start (Starter motor
turns over)Throttle lever Squeezed Release 26
Fuel Empty Refill as soon as pos-
sible39
Stale or contaminat-
edHave serviced by
Yamaha dealer70
Fuel tank Water or dirt present Have serviced by
Yamaha dealer70
Spark plug Fouled or defective Clean or replace 72
Spark plug
capNot connected or
looseConnect properly
72
Connected to wrong
cylinderConnect properly
72
Fuel injec-
tion systemFuel pump faulty Have serviced by
Yamaha dealer—
UF1K73E0.book Page 78 Wednesday, July 11, 2007 9:15 AM
Page 86 of 94
Trouble recovery
79
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible39
Stale or contaminat-
edHave serviced by
Yamaha dealer70
Fuel tank Water or dirt present Have serviced by
Yamaha dealer70
Spark plug Fouled or defective Replace 72
Incorrect heat range Replace 72
Gap incorrect Adjust 72
Spark plug
capLoose Connect properly 72
Cracked, torn, or
damagedHave serviced by
Yamaha dealer—
Electrical wir-
ingLoose connection Have serviced by
Yamaha dealer—
Fuel injec-
tion systemFaulty or clogged in-
jectorsHave serviced by
Yamaha dealer—
Warning light or in-
dicator blinksFuel level Empty Refill as soon as pos-
sible39
Engine over-
heatedJet intake clogged Clean
80
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer34
Watercraft slow or
loses powerYamaha Se-
curity Sys-
tem (VX
Deluxe/VX
Cruiser)Low-RPM mode se-
lectedSelect normal mode
30
Cavitation Jet intake clogged Clean 80
Impeller damaged or
wornHave serviced by
Yamaha dealer80
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine33
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
32
Spark plug Fouled or defective Replace 72
Incorrect heat range Replace 72
Gap incorrect Adjust 72
Spark plug
capsLoose Connect properly
72
Electrical wir-
ingLoose connection Have serviced by
Yamaha dealer—
Fuel Stale or contaminat-
edHave serviced by
Yamaha dealer70
Air filter Clogged or oil buildup Have serviced by
Yamaha dealer71 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF1K73E0.book Page 79 Wednesday, July 11, 2007 9:15 AM
Page 93 of 94
Index
Operating your watercraft......................... 52
Operation ................................................. 49
Operation of controls and other
functions ............................................... 23
Operation requirements ........................... 11
Owner’s/operator’s manual and tool kit .... 67
P
Periodic maintenance chart...................... 68
Post-operation care .................................. 61
Pre-operation check list............................ 40
Pre-operation check points ...................... 42
Pre-operation checks ............................... 40
Primary Identification (PRI-ID) number ...... 1
R
Recommended equipment ....................... 13
Remote control transmitter
(for VX Deluxe/VX Cruiser) ................... 24
Reverse on waterways
(for VX Deluxe/VX Cruiser) ................... 60
Riding with passengers ............................ 53
Rough water operation ............................. 61
S
Safe boating rules .................................... 17
Seat .......................................................... 23
“SECURITY” indicator light
(for VX Deluxe/VX Cruiser) ................... 34
Selecting the normal mode/low-RPM
mode (for VX Deluxe/VX Cruiser) ......... 30
Shift cable, checking (for VX Deluxe/
VX Cruiser) ........................................... 71
Shift lever and reverse gate
(for VX Deluxe/VX Cruiser) ................... 46
Shift lever (for VX Deluxe/VX Cruiser) ..... 27
Spark plugs, cleaning and adjusting ........ 72
Speedometer............................................ 31
Start switch............................................... 26
Starting the engine ................................... 49
Starting the watercraft .............................. 53
Steering system ................................. 27, 45
Stern drain plugs ...................................... 44
Stern eyes ................................................ 28
Stopping the engine ................................. 51
Stopping the watercraft ............................ 60
Storage..................................................... 63
Storage compartments ............................. 35Submerged watercraft .............................. 83
Switches ................................................... 48
T
Tachometer .............................................. 31
Throttle cable, checking and adjusting ..... 72
Throttle lever ...................................... 26, 45
Towing the watercraft ............................... 83
Transporting ............................................. 62
Trolling speed, checking .......................... 76
Troubleshooting ....................................... 78
Troubleshooting chart .............................. 78
Turning the watercraft .............................. 58
W
Water separator ....................................... 43
Watercraft characteristics ......................... 14
Water-skiing ............................................. 16
Y
Yamaha Engine Management System
(YEMS) ................................................. 28
Yamaha Security System and low-RPM
mode (for VX Deluxe/VX Cruiser) ......... 29
Yamaha Security System
(for VX Deluxe/VX Cruiser) ................... 29
Yamaha Security System lock and
unlock modes (for VX Deluxe/
VX Cruiser) ........................................... 29
UF1K73E0.book Page 2 Wednesday, July 11, 2007 9:15 AM