stop start YAMAHA VX CRUISER 2007 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2007, Model line: VX CRUISER, Model: YAMAHA VX CRUISER 2007Pages: 96, PDF Size: 6.88 MB
Page 6 of 96
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1
Model information
(for Europe only) ......................... 2
Builder’s plate .................................... 2
Emission control information
(for Canada only) ........................ 3
Approval label of emission control
certificate ........................................ 3
Manufactured date label .................... 4
Important labels .............................. 5
Warning labels ................................... 6
Other labels ....................................... 9
Safety information ........................... 12
Limitations on who may operate
the watercraft ............................ 12
Cruising limitations ....................... 13
Operation requirements ............... 14
Recommended equipment ........... 16
Hazard information ....................... 17
Watercraft characteristics ............. 17
Water-skiing ................................. 19
Safe boating rules ........................ 20
Enjoy your watercraft
responsibly ................................ 21
Features and functions ................... 22
Location of main components ...... 22
Operation of controls and other
functions .................................... 26
Seat ................................................. 26
Hood ................................................ 26
Fuel tank filler cap ........................... 27
Remote control transmitter
(for VX Deluxe/VX Cruiser) .......... 27
Engine stop switch .......................... 28
Engine shut-off switch ..................... 28
Start switch ...................................... 29Throttle lever ................................... 29
Cooling water pilot outlet ................. 29
Steering system ............................... 30
Shift lever
(for VX Deluxe/VX Cruiser) .......... 30
Handgrip .......................................... 31
Bow eye ........................................... 31
Stern eyes ....................................... 31
Yamaha Engine Management
System (YEMS) ........................... 32
Yamaha Security System and
low-RPM mode
(for VX Deluxe/VX Cruiser) .......... 32
Multifunction information center ...... 34
Storage compartments .................... 38
Operation ......................................... 41
Fuel and oil .................................. 41
Gasoline .......................................... 41
Engine oil ......................................... 42
Filling the fuel tank .......................... 42
Pre-operation checks ................... 43
Pre-operation check list ................... 43
Pre-operation check points .............. 45
Operation ..................................... 51
Engine break-in ............................... 51
Launching the watercraft ................. 52
Starting the engine .......................... 52
Stopping the engine ........................ 54
Leaving the watercraft ..................... 54
Operating your watercraft ............ 54
Getting to know your watercraft ....... 54
Learning to operate your
watercraft ..................................... 54
Riding with passengers ................... 55
Starting the watercraft ..................... 56
Boarding and starting in deep
water ............................................ 57
Capsized watercraft ......................... 60
Turning the watercraft ..................... 61
Stopping the watercraft ................... 62
Beaching the watercraft ................... 63
Docking the watercraft ..................... 63
UF1K72E0.book Page 1 Wednesday, August 2, 2006 10:43 AM
Page 23 of 96
Safety information
16
Always consult your doctor on whether it is
safe for you to ride this watercraft if you are
pregnant or in poor health.
Do not attempt to modify this watercraft!
Modifications to your watercraft may reduce
safety and reliability, and render the water-
craft unsafe or illegal for use.
Attach the engine shut-off cord to your left
wrist and keep it free from the handlebars
so that the engine stops if you, the operator,
fall off. After riding, remove the engine shut-
off cord from the watercraft to avoid acci-
dental starting or unauthorized use by chil-
dren or others.
Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit some-
one in the water.
Avoid being hit by another boat! You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you ma-
neuver more quickly than other boaters ex-
pect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Safe boating
rules” and be sure to check behind you be-
fore making a turn. (See “Safe boating
rules” on page 20.)
EJU30840
Recommended equipment
The following items should be carried on
board your watercraft:
Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to signal
other boats.
Visual distress signals
It is recommended that a pyrotechnic de-
vice, which is approved by the appropriate
authorities, be stored in a waterproof con-
tainer on your watercraft. A mirror can also
be used as an emergency signal. Contact a
Yamaha dealer for more information.
Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
Towline
A towline can be used to tow a disabled wa-
tercraft in an emergency.
UF1K72E0.book Page 16 Wednesday, August 2, 2006 10:43 AM
Page 24 of 96
Safety information
17
EJU30870
Hazard information
Never start the engine or let it run for any
length of time in an enclosed area. Exhaust
fumes contain carbon monoxide, a color-
less, odorless gas that may cause loss of
consciousness and death within a short
time. Always operate the watercraft in an
open area.
Do not touch the hot oil tank, muffler, or en-
gine during or immediately after engine op-
eration; they can cause serious burns.
EJU30930
Watercraft characteristics
Jet thrust turns the watercraft. Releasing
the throttle lever completely produces only
minimum thrust. If you are traveling at
speeds above trolling, you will have rapidly
decreasing ability to steer without throttle.
This model is equipped with the Yamaha
Engine Management System (YEMS) that
includes an off-throttle steering (OTS) sys-
tem. It will activate at planing speeds should
you attempt to steer the watercraft after re-
leasing the throttle lever. The OTS system
assists in turning by continuing to supply
some thrust while the watercraft is deceler-
ating, but you can turn more sharply if you
apply throttle while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed.
Practice turning in an open area without ob-
stacles until you have a good feel for this
maneuver.
This watercraft is water-jet propelled. The
jet pump is directly connected to the engine.
This means that jet thrust will produce some
movement whenever the engine is running.
There is no “neutral” position. You are in ei-
ther “forward” or “reverse”, depending upon
the shift lever position (for VX Deluxe/VX
Cruiser).
For VX Deluxe/VX Cruiser:
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or im-
pact the handlebars.
This could increase the risk of back/spinal
injury (paralysis), facial injuries, and broken
UF1K72E0.book Page 17 Wednesday, August 2, 2006 10:43 AM
Page 31 of 96
Features and functions
24
Control system
1Start switch
2Engine shut-off switch
3Clip
4Multifunction information center
5Rearview mirrors (for VX Deluxe/VX Cruis-
er)
6Shift lever (for VX Deluxe/VX Cruiser)
7Throttle lever
8Glove compartment
9Remote control transmitter (for VX De-
luxe/VX Cruiser)
10Engine stop switch
11Engine shut-off cord (lanyard)
UF1K72E0.book Page 24 Wednesday, August 2, 2006 10:43 AM
Page 35 of 96
Features and functions
28
If the remote control transmitter needs a
new battery or is not operating properly,
contact a Yamaha dealer. Do not attempt
to replace the battery yourself.
NOTE:
While the engine is running, input from the re-
mote control transmitter is not received.
For Canada only
IC (Industry Canada) rules:
Operation is subject to the following two con-
ditions; (1) this device may not cause interfer-
ence, and (2) this device must accept any
interference received, including interference
that may cause undesired operation of the de-
vice.
EJU31150Engine stop switch
Push the engine stop switch (red button) to
stop the engine normally.
EJU31160Engine shut-off switch
Insert the clip, on the end of the engine shut-
off cord, under the engine shut-off switch
(black button). The engine will stop automati-
cally when the clip is removed from the
switch, such as if the operator falls off the wa-
tercraft.
WARNING
EWJ00010
Always attach the engine shut-off cord
to your left wrist and the clip to the en-
gine shut-off switch BEFORE starting
the engine.
1Transmitter holder
1Engine stop switch
1Clip
2Engine shut-off cord
3Engine shut-off switch
UF1K72E0.book Page 28 Wednesday, August 2, 2006 10:43 AM
Page 36 of 96
Features and functions
29
To prevent accidental starting of the en-
gine or unauthorized use by children or
others, always remove the clip from the
engine shut-off switch when the engine
is not running.
EJU31190Start switch
Push the start switch (green button) to start
the engine.
NOTE:
The engine will not start when the lock mode
of the Yamaha Security System has been se-
lected (for VX Deluxe/VX Cruiser), the clip is
removed from the engine shut-off switch, or
the throttle lever is squeezed. (See page 32
for Yamaha Security System and low-RPM
mode selection procedures.)
EJU31210Throttle lever
Squeeze the throttle lever to increase engine
speed.
Release the throttle lever to decrease engine
speed or to return it to the idle position.
EJU35971Cooling water pilot outlet
This watercraft is equipped with a cooling wa-
ter pilot outlet.
When the engine is running, cooling water is
circulated in the engine, and then it is dis-
charged from the pilot outlet.
To check for proper operation of the cooling
system, check that water is being discharged
from the pilot outlet. If water is not being dis-
charged from the outlet, cooling water may
not be circulating in the engine. When this oc-
curs, stop the engine and check for the cause.
(See pages 36 and 82 for more information.)
1Start switch
1Throttle lever
UF1K72E0.book Page 29 Wednesday, August 2, 2006 10:43 AM
Page 39 of 96
Features and functions
32
EJU31370Yamaha Engine Management System
(YEMS)
This model is equipped with an integrated,
computerized management system that con-
trols and adjusts ignition timing, fuel injection,
engine diagnostics, and the off-throttle steer-
ing (OTS) system.
EJU31380Yamaha Security System and low-
RPM mode (for VX Deluxe/VX Cruiser)
This watercraft is equipped with a remote con-
trol transmitter that is used to select the secu-
rity system and low-RPM mode settings.
Since the watercraft is programmed to recog-
nize the internal code from this transmitter
only, the security system setting can only be
changed with this transmitter. If you lose the
remote control transmitter or it does not oper-
ate properly, contact a Yamaha dealer.
EJU31390Yamaha Security System (for VX Deluxe/
VX Cruiser)
The Yamaha Security System functions to
help prevent unauthorized use or theft of the
watercraft. The engine cannot be started if the
security system is in the lock mode. The en-
gine can only be started in the unlock mode.
EJU36102Yamaha Security System lock and unlock
modes (for VX Deluxe/VX Cruiser)
The lock and unlock modes of this system can
only be selected while the engine is stopped.
When the lock button on the remote control
transmitter is pressed, the beeper soundsonce. This indicates the lock mode is selected
and the engine cannot be started.
The “SECURITY” indicator light comes on
when the security system is in the unlock
mode and goes off when the security system
is in the lock mode.
When the unlock button on the remote control
transmitter is pressed for a short time, the
beeper sounds two times for the normal mode
or three times for the low-RPM mode. The
“SECURITY” indicator light will come on and
the engine can be started. (See the items in
1Lock button
1“SECURITY” indicator light
UF1K72E0.book Page 32 Wednesday, August 2, 2006 10:43 AM
Page 40 of 96
Features and functions
33
“Selecting the normal mode/low-RPM mode”
for operation mode information.)
EJU31411Selecting the normal mode/low-RPM
mode (for VX Deluxe/VX Cruiser)
The normal mode and low-RPM mode can
only be selected when the engine is stopped
in the unlock mode. Press the unlock button
on the remote control transmitter for more
than 4 seconds to switch between the normal
mode and the low-RPM mode.
Normal mode
If the beeper sounds twice, the normal mode
is activated.
The watercraft can be ridden normally.Low-RPM mode
If the beeper sounds three times, the low-
RPM mode is activated and the “L-MODE” in-
dicator light comes on.
Maximum engine speed (r/min) in the low-
RPM mode is limited to approximately 90% of
the maximum engine speed in the normal
mode.
NOTE:
If neither the start switch nor the remote
control transmitter is operated within 25
seconds after the unlock button is pressed
to select the unlock mode, the multifunction
meter display and the “L-MODE” indicator
light will go off. If this occurs, press the lock
button on the transmitter briefly to select the
lock mode, press the unlock button briefly to
select the unlock mode, and then press the
unlock button again for more than 4 sec-
onds to select the normal mode or low-RPM
mode.
While the engine is running, input from the
remote control transmitter is not received.
CAUTION:
ECJ00080
If the remote control transmitter does not
operate when its buttons are pressed, the
battery may be low. Have a Yamaha dealer
replace the battery.
1Unlock button
Number
of beepsYamaha Security Sys-
tem modeEngine
can be
started
1 beep Lock NO
2 beepsUnlock
(normal mode)YES
3 beepsUnlock
(low-RPM mode)YES
1“L-MODE” indicator light
UF1K72E0.book Page 33 Wednesday, August 2, 2006 10:43 AM
Page 41 of 96
Features and functions
34
EJU31451Multifunction information center
This meter contains the following functions for
help and convenience in operating the water-
craft.
CAUTION:
ECJ00071
Do not run the engine for more than 15
seconds without supplying water or over
4000 r/min on land when checking the op-
eration of the meter, otherwise the engine
could overheat.
NOTE:
When the engine is started, all displays light
up for 2 seconds, and then the meter starts
to operate normally.
The current display will continue to operate
for 25 seconds after the engine stops.
EJU31460Tachometer
The engine speed (r/min) is displayed by seg-
ments. Each segment indicates a 250 r/min
increment.
EJU31500Speedometer
The meter shows the watercraft speed
against water.
NOTE:
To switch the speedometer display between
kilometers and miles, push the select button
for at least 1 second, within 10 seconds after
the meter is displayed.
EJU31510Fuel level meter
The fuel level meter is provided for convenient
fuel level checking while riding.
1Tachometer
2Speedometer
3Hour meter/voltmeter
4Fuel level meter
5“L-MODE” indicator light (for VX Deluxe/VX
Cruiser)
6“WARNING” light
7Fuel level warning indicator
8Oil pressure warning indicator
9Engine overheat warning indicator
10Check engine warning indicator
11Select button
12“SECURITY” indicator light (for VX Deluxe/
VX Cruiser)
1Select button
UF1K72E0.book Page 34 Wednesday, August 2, 2006 10:43 AM
Page 43 of 96
Features and functions
36
sure warning indicator begin to blink, and the
buzzer sounds intermittently. At the same
time, the engine speed is limited to help pre-
vent damage.
If this occurs, reduce the engine speed, return
to shore, and then check the engine oil level.
(See page 45 for engine oil level checking
procedures.) If the oil level is low, add enough
engine oil to raise it to the proper level. If the
oil level is sufficient, have a Yamaha dealer
check the watercraft.
NOTE:
Press the select button on the multifunction
meter to stop the buzzer.
EJU31602Engine overheat warning indicator
This model is equipped with an engine over-
heat warning system.
If the engine starts to overheat, the “WARN-
ING” light and the engine overheat warning in-dicator blink, and then come on. The buzzer
also begins to sound intermittently, and then it
sounds continuously. After the light and indi-
cator start to blink and the buzzer sounds, the
engine speed is limited to help prevent dam-
age.
If this occurs, immediately reduce the engine
speed, return to shore, and then check for wa-
ter discharge at the port (left) cooling water pi-
lot outlet while the engine is running. If there
is no discharge of water, shut the engine off,
and then check the intake grate and impeller
for clogging.
WARNING
EWJ00050
Before attempting to remove weeds or de-
bris from the intake grate or impeller, shut
the engine off and remove the clip from the
engine shut-off switch. Severe injury or1Select button
UF1K72E0.book Page 36 Wednesday, August 2, 2006 10:43 AM