storage YAMAHA VX CRUISER 2022 Owners Manual

Table of contents
Accessory outlet ........................... 53
USB charger.................................. 53
Equipment operation ...................... 54 Equipment ..................................... 54
Seats ................................................ 54
Handgrip .......................................... 55
Reboarding grip ............................... 55
Reboarding step (VX / VX DELUXE /
VX CRUISER / VX LIMITED).......... 55
Bow eye ........................................... 56
Stern eyes ........................................ 56
Cleat ................................................. 56
Pull-up cleats (VX CRUISER / VX LIMITED) ....................................... 57
Storage compartments .................... 57
Fire extinguisher holder and cover ... 60
Operation and handling
requirements ................................... 61 Fuel requirements ......................... 61
Fuel................................................... 61
Engine oil requirements ................ 63
Engine oil .......................................... 63
Draining the bilge water ................ 65
Draining the bilge water on land ...... 65
Draining the bilge water on water .... 65
Transporting on a trailer ................ 66
First-time operation ........................ 67 Engine break-in ............................. 67
Pre-operation checks ..................... 68
Pre-operation checklist .................... 68
Pre-operation check points........... 70
Pre-launch checks ........................... 70
Post-launch checks ......................... 75
Operation ......................................... 77 Operating your watercraft ............. 77
Getting to know your watercraft ...... 77
Learning to operate your
watercraft ...................................... 77 Riding position ................................. 78
Launching the watercraft ................. 78
Starting the engine on water ............ 78
Stopping the engine ......................... 79
Leaving the watercraft ...................... 80
Operating the watercraft .................. 80
Turning the watercraft ...................... 81
Stopping the watercraft.................... 82
Operating the watercraft in reverse
or neutral (VX / VX DELUXE /
VX CRUISER / VX LIMITED) .......... 83
Boarding the watercraft.................... 84
Starting off........................................ 87
Capsized watercraft ......................... 88
Beaching and docking the watercraft ...................................... 88
Operating in weeded areas .............. 89
After removing the watercraft from
the water ....................................... 90
Care and storage ............................ 91Post-operation care ...................... 91
Flushing the cooling water
passages....................................... 91
Cleaning the watercraft .................... 92
Battery care ...................................... 92
Long-term storage ........................ 94
Cleaning ........................................... 94
Lubrication ....................................... 94
Rustproofing ..................................... 95
Maintenance .................................... 97 Maintenance ................................. 97
Periodic maintenance chart ............. 98
Engine oil and oil filter .................... 100
Specifications ................................ 101Specifications ............................. 101
Trouble recovery ........................... 103 Troubleshooting .......................... 103
Troubleshooting chart .................... 103
UF4N71E0.book Page 2 Thursday, August 5, 2021 11:58 AM

General and important labels
1
EJU36453
Identification numbers
Record the Primary Identification (PRI-ID)
number, Craft Identification Number (CIN),
and engine serial number in the spaces pro-
vided for assistance when ordering spare
parts from a Yamaha dealer. Also record and
keep these ID numbers in a separate place in
case your watercraft is stolen.
EJU30284Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a plate at-
tached inside the engine compartment. (See
page 54 for seat removal and installation pro-
cedures and page 59 for information on the
seat storage compartment.)
MODEL:
VX1050G-X (VX-C)
VX1050F-X (VX)
VX1050E-X (VX DELUXE)
VX1050D-X (VX DELUXE)
VX1050C-X (VX CRUISER)
VX1050B-X (VX CRUISER)
VX1050A-X (VX LIMITED)
EJU36551Craft Identification Number (CIN)
The CIN is stamped on a plate attached to
the aft deck.
EJU30312Engine serial number
The engine serial number is stamped on a
plate attached to the engine unit. (See page
54 for seat removal and installation proce-
dures.)
1Primary Identification (PRI-ID) number loca-
tion
11Craft Identification Number (CIN) location
MODELYAMAHA MOTOR CO.,LTD.
ASSEMBLED IN U.S.A. WITH FOREIGN AND DOMESTIC COMPONENTS.
ASSEMBLÉ EN U.S. AVEC DES COMPOSANTS ÉTRANGERS ET
DOMESTIQUES. PRI-I.D.
1
UF4N71E0.book Page 1 Thursday, August 5, 2021 11:58 AM

Description
24
Engine compartment
1
6
7
8
5
2 43
1
Air filter case
2 Spark plug/Ignition coil
3 Seat storage compartment (page 59)
4 Battery (page 71)
5 Fuel tank
6 Water separator (page 29)
7 Flushing hose connector (page 91)
8 Oil tank filler cap/Dipstick (page 63)
UF4N71E0.book Page 24 Thursday, August 5, 2021 11:58 AM

Equipment operation
54
EJU40336
EquipmentEJU31045Seats
The front and rear seats are removable.
Remove the seats to access the engine com-
partment and seat storage compartment.
To remove the rear seat:
(1) Pull the rear seat latch up, and then lift upthe rear of the seat.
(2) Pull the seat rearward and remove it.
To install the rear seat:
(1) Insert the projections on the front of the seat into the stays on the deck. (2) Push the rear of the seat down to secure-
ly lock it in place.
To remove the front seat:
(1) Remove the rear seat.
(2) Pull the front seat latch up, and then liftup the rear of the seat.
(3) Pull the seat rearward and remove it.
1 Seat latch
1
1Seat latch
1
UF4N71E0.book Page 54 Thursday, August 5, 2021 11:58 AM

Equipment operation
57
weight. If the cleat breaks, the watercraft
could fall, which could result in severe in-
jury.
[EWJ01511]
EJU34894
Pull-up cleats (VX CRUISER / VX
LIMITED)
The pull-up cleats are used to attach a rope
to the watercraft when mooring it.
To use a pull-up cleat, pull it up. The pull-up
cleat returns automatically to its original posi-
tion when released. WARNING! Do not use
the pull-up cleats to lift the watercraft. The
pull-up cleats are not designed to support
the watercraft’s weight. If the pull-up
cleats break, the watercraft could fall,
which could result in severe injury.
[EWJ00822] EJU31685
Storage compartments
This watercraft is equipped with the following
storage compartments.
The storage compartments are not designed
to be waterproof. If you carry objects that
must be kept dry, put them in a waterproof
bag.
Make sure that the storage compartments
are closed securely before operating the wa-
tercraft.
EJU45250Bow storage compartment
The bow storage compartment is located un-
der the hood.
To open the bow storage compartment:
Pull the hood latch rearward, and then lift up
the rear of the hood.
1
Cleat
1 Pull-up cleat (VX CRUISER / VX LIMITED)
2 Pull-up cleat (VX LIMITED)
1
2
1
1Hood latch
1 Bow storage compartment
1
1
UF4N71E0.book Page 57 Thursday, August 5, 2021 11:58 AM

Equipment operation
58
To close the bow storage compartment:
Push the rear of the hood down to securely
lock it in place.
EJU46211Glove compartment
The glove compartment is located in front of
the seat.
TIP
Make sure the seal of lid is intact, clear and
properly positioned before using.
Make sure the seals around the USB char-
ger and 12V DC outlet are intact and prop-
erly positioned before using.
Completely dry inside of the glove com-
partment and its contents before and after
using.
Make sure nothing is pinches between the
glove compartment and the lid when clos-
ing the glove compartment.
When not in use, the rubber caps for the
USB charger and 12V DC outlet should be
installed to cover the connectors.
To open the glove compartment:
Pull the glove compartment latch up, and
then lift up the lid.
To close the glove compartment:
Push the lid down to securely lock it in place.
Bow storage compartment:
Capacity:
92.0 L (24.3 US gal, 20.2 Imp.gal)
Load limit: 5.0 kg (11 lb)
1Glove compartment latch
1 Glove compartment
Glove compartment:
Capacity: 16.5 L (4.4 US gal, 3.6 Imp.gal)
Load limit: 1.5 kg (3 lb)
1
1
UF4N71E0.book Page 58 Thursday, August 5, 2021 11:58 AM

Equipment operation
59
To drain water from the glove compart-
ment:
(1) Remove the drain plug on the bottom ofthe glove compartment to drain the wa-
ter.
(2) Securely install the drain plug in it original position.
EJU46011Seat storage compartment
The seat storage compartment is located un-
der the rear seat.
The storage compartment is removable.
To open the seat storage compartment:
(1) Remove the rear seat. (See page 54 forseat removal and installation proce-
dures.)
(2) Push the latch forward, and then lift up the lid and remove it.
To close the seat storage compartment:
(1) Insert the projections on the lid into theslots on the seat storage compartment.
(2) Push the rear of the lid down.
1 Drain plug
1 Lid
2 Latch
1
2
1
1
Seat storage compartment
Seat storage compartment:
Capacity: 5.4 L (1.4 US gal, 1.2 Imp.gal)
Load limit:
3.0 kg (7 lb)
1
UF4N71E0.book Page 59 Thursday, August 5, 2021 11:58 AM

Equipment operation
60
(3) Securely install the rear seat in its originalposition.
EJU46030Fire extinguisher holder and cover
The fire extinguisher holder and cover are lo-
cated in the bow storage compartment.
To use the fire extinguisher holder and
cover:
(1) Pull the hood latch rearward, and then liftup the rear of the hood.
(2) Unhook the band and remove the fire ex- tinguisher from the fire extinguisher cov-
er.
(3) Place the fire extinguisher in the fire ex- tinguisher cover, and then securely fas-
ten the fire extinguisher with the band.
(4) Push the rear of the hood down to se- curely lock it in place. Make sure that the hood is securely closed before using the
watercraft.
1
Hood latch
1 Fire extinguisher holder and cover
2 Band
1
2
1
UF4N71E0.book Page 60 Thursday, August 5, 2021 11:58 AM

Pre-operation checks
68
EJU31984
EWJ00413
Failure to inspect or maintain the watercraft properly increases the possibility of an ac-
cident or damage to the watercraft. Do not operate the watercraft if you find any prob-
lem. If a problem cannot be corrected by the procedures provided in this manual, have
the watercraft inspected by a Yamaha dealer.
EJU41237Pre-operation checklist
Before using this watercraft, be sure to perform the checks in the following checklist.
PRE-LAUNCH CHECKS
ITEM ROUTINEPAGE
Engine compartment Ventilate the engine compartment.
Check inside the engine compartment for damage.
70
Fuel system Check the fuel system for leakage.
Check the fuel level in the fuel tank.
70
Water separator Check the water separator for water. 70
Engine unit Check the exterior of the engine unit for damage. 71
Engine oil level Check the engine oil level. 71
Bilge water Check the engine compartment for bilge water. 71
Battery Check the battery connections. 71
Steering system Check the steering system for proper operation. 71
RiDE lever (VX /
VX DELUXE /
VX CRUISER / VX LIMITED) Check the RiDE lever for proper operation.
72
Throttle lever Check the throttle lever for proper operation. 72
Yamaha Security System
(VX DELUXE /
VX CRUISER / VX LIMITED) Check the Yamaha Security System for proper op-
eration.
72
Engine shut-off cord (lan-
yard) Check the engine shut-off cord (lanyard) for dam-
age.
72
Switches VX-C:
Check the start switch, engine stop switch, and en-
gine shut-off switch for proper operation.
VX / VX DELUXE / VX CRUISER / VX LIMITED:
Check the engine start/stop switch and engine
shut-off switch for proper operation.
73
Storage compartments Check the storage compartments for damage and
water.
74
Fire extinguisher holder,
cover, and band Check the fire extinguisher holder, cover, and band
for damage.
74
Fire extinguisher Check the condition of the fire extinguisher. 74
Safety equipment Check that safety equipment meeting the applica-
ble regulations is on board.
74
UF4N71E0.book Page 68 Thursday, August 5, 2021 11:58 AM

Pre-operation checks
70
EJU32282
Pre-operation check pointsEJU40099Pre-launch checks
Perform the pre-launch checks in the pre-op-
eration checklist while the watercraft is on
land.
To perform the pre-launch checks:
(1) Remove the seats and seat storagecompartment. (See page 54 for seat re-
moval and installation procedures and
page 59 for information on the seat stor-
age compartment.)
(2) Perform the checks and make sure that there are no malfunctioning items or oth-
er problems.
(3) After completing these checks, securely install the seat storage compartment and
seats in their original positions.
EJU32334Engine compartment checkEWJ00462
Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak.
Ventilate the engine compartment. Leave the
engine compartment open for a few minutes
to allow any fuel vapors to escape.
Make sure that there is no damage inside the
engine compartment.
EJU34215Fuel system checksEWJ00382
Leaking fuel can result in fire or explosion.
Check for fuel leakage regularly.
If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
watercraft unsafe to operate.
Make sure that there is no damage, leakage,
or other problem in the fuel system.
Check:
Fuel filler cap and seal for damage
Fuel tank for damage and leakage
Fuel hoses and joints for damage and leak-
age
Fuel tank breather hose for damage and
leakage
EJU36875Fuel level check
Check the fuel level in the fuel tank.
Add fuel if necessary. (See page 61 for infor-
mation on filling the fuel tank.)
EJU32424Water separator check
Make sure that no water has collected in the
water separator. If water has collected in the
water separator, drain it. (See page 29 for in-
formation on draining the water separator.)
1Water separator
1
UF4N71E0.book Page 70 Thursday, August 5, 2021 11:58 AM