stop start YAMAHA VX CRUISER HO 2022 User Guide

Instrument operation
42
center display. (See page 24 for Yamaha Se-
curity System setting procedures.)
EJU46400Warning function
The multifunction information center can indi-
cate the following warnings.
Fuel level warning
Battery voltage warning
Check engine warning
Engine overheat warning
Oil pressure warning
Other warnings (communication errors, ex-
ceeding the maintenance intervals, and so
on)
To stop the buzzer when a malfunction is ac-
tivated, correct the cause of the problem and
start the engine again, or push the “OK” but-
ton of the touchpad control.
Fuel level warning
If the amount of remaining fuel is low, the low-
est fuel level segment blinks orange, “Low
Fuel” is displayed on the display, and the
buzzer sounds intermittently. If the fuel level warning is activated, refill the
fuel tank as soon as possible. (See page 54
for information on filling the fuel tank.)
Battery voltage warning
If the battery voltage is less than 12 volts or
more than 18 volts when the engine is not
running, the voltage display of the voltmeter
blinks.
If the battery voltage warning is activated,
have the watercraft serviced by a Yamaha
dealer as soon as possible.
Check engine warning “ ”
If a sensor malfunction or a short circuit is
detected, “ ” is shown in the warning bar,
and the buzzer sounds intermittently.
If the check engine warning is activated, im-
mediately reduce the engine speed, return to
1
“OK” button
1
14.3V
km/h
RPM
Low
Fuel
10.8V
km/h
RPM
UF4S71E0.book Page 42 Wednesday, August 4, 2021 5:18 PM

Pre-operation checks
61
EJU31984
EWJ00413
Failure to inspect or maintain the watercraft properly increases the possibility of an ac-
cident or damage to the watercraft. Do not operate the watercraft if you find any prob-
lem. If a problem cannot be corrected by the procedures provided in this manual, have
the watercraft inspected by a Yamaha dealer.
EJU41237Pre-operation checklist
Before using this watercraft, be sure to perform the checks in the following checklist.
PRE-LAUNCH CHECKS
ITEM ROUTINEPAGE
Engine compartment Ventilate the engine compartment.
Check inside the engine compartment for damage.
63
Fuel system Check the fuel system for leakage.
Check the fuel level in the fuel tank.
63
Water separator Check the water separator for water. 63
Engine unit Check the exterior of the engine unit for damage. 64
Engine oil level Check the engine oil level. 64
Bilge water Check the engine compartment for bilge water. 64
Battery Check the battery connections. 64
Steering system Check the steering system for proper operation. 64
RiDE lever Check the RiDE lever for proper operation. 65
Throttle lever Check the throttle lever for proper operation. 65
Yamaha Security System Check the Yamaha Security System for proper op-
eration.
65
Engine shut-off cord (lan-
yard) Check the engine shut-off cord (lanyard) for dam-
age.
65
Switches Check the engine start/stop switch and engine
shut-off switch for proper operation.
66
Storage compartments Check the storage compartments for damage and
water.
66
Fire extinguisher holder,
cover, and band Check the fire extinguisher holder, cover, and band
for damage.
66
Fire extinguisher Check the condition of the fire extinguisher. 67
Safety equipment Check that safety equipment meeting the applica-
ble regulations is on board.
67
Hull and deck Check the hull and deck for damage. 67
Jet intake Check the jet intake for damage and clogging. 67
Jet thrust nozzle and re-
verse gate Check the jet thrust nozzle and reverse gate for
damage.
67
Stern drain plugs Check the stern drain plugs for damage and foreign
material and check that they are securely installed.
67
UF4S71E0.book Page 61 Wednesday, August 4, 2021 5:18 PM

Pre-operation checks
66
EJU46050Switch checksECJ01311
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
Check the engine start/stop switch and the
engine shut-off switch for proper operation.
(See page 25 for information on operating
each switch.)
To check the operation of the switches:
(1) If the lock mode is selected for theYamaha Security System setting, selectthe unlock mode. (See page 24 for
Yamaha Security System setting proce- dures.)
(2) Push the engine start/stop switch to make sure that the engine starts.
(3) As soon as the engine starts running, push the engine start/stop switch to
make sure that the engine stops immedi-
ately.
(4) Restart the engine, and then pull the en- gine shut-off cord (lanyard) to remove
the clip from the engine shut-off switch
to make sure that the engine stops im-
mediately.
EJU40102Storage compartment checks
Make sure that the storage compartments
are not damaged and that water has not col-
lected in the compartments. (See page 50 for
information on the storage compartments.)
EJU43800Fire extinguisher holder, cover, and band
checks
Make sure that the fire extinguisher holder,
cover, and band are not damaged and that
the fire extinguisher is securely held in place
using the band. (See page 53 for information
1Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)
12
3
1Engine start/stop switch
1
UF4S71E0.book Page 66 Wednesday, August 4, 2021 5:18 PM

Operation
72
is attached correctly. If the engine
shut-off cord (lanyard) is not attached
correctly, it may not pull free when the
operator falls off, allowing the water-
craft to continue to run and cause an
accident.
[EWJ00583]
(4) With the throttle lever released, push theengine start/stop switch (red button) to
start the engine. (See page 25 for infor-
mation on operating the engine
start/stop switch.)
EJU46080Stopping the engine
Release the throttle lever, and then push the
engine start/stop switch (red button) to stop
the engine. WARNING! You need throttle to
steer. Shutting the engine off can cause
you to hit an obstacle you are attempting to avoid. A collision could result in severe
injury or death.
[EWJ00602]
EJU32874
Leaving the watercraft
If leaving the watercraft, remove the clip from
the engine shut-off switch to prevent acci-
dental starting or unauthorized operation by
children or others.
EJU43411Operating the watercraft
When the throttle lever is squeezed, the “F”
(forward) shift indicator will be displayed and
the watercraft will move forward. While the
“F” (forward) shift indicator is displayed, the
watercraft will move forward at trolling speed
even if the throttle lever is in the fully closed
(idle) position. (See page 28 for shift system
operation procedures.)
1 Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)
12
3
UF4S71E0.book Page 72 Wednesday, August 4, 2021 5:18 PM

Operation
77
(3) Pull yourself up onto the boarding plat-form and grasp the handgrip, and then
move to the seat and sit astride.
(4) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip
to the engine shut-off switch.
(5) Grip the handlebars with both hands and place both feet on the floor of the foot-
well.
(6) Look in all directions, start the engine, and then start off slowly.
EJU43260Boarding with passenger(s)EWJ01800
Severe internal injuries can occur if wa-
ter is forced into body cavities as a re-
sult of being near the jet thrust nozzle.
Do not start the engine until the passen-
gers are seated with their feet on the
floor of the footwell and are securely holding on to the person in front of them
or to the handgrip provided.
Before boarding the watercraft, make
sure that the engine is stopped. If the
engine is running, the reverse gate may
move down and a person boarding
could be pinched.
The heavier the total weight of the operator
and passenger(s), the more difficult it will be
to balance the watercraft. Do not operate the
watercraft when the total weight exceeds 240
kg (530 lb) including any cargo.
To board with passenger(s):
(1) Board as noted in the previous section
“Boarding alone”.
(2) Grip the handlebars with both hands and place both feet on the floor of the foot-
well.
(3) Have the first passenger move to the rear of the watercraft.
UF4S71E0.book Page 77 Wednesday, August 4, 2021 5:18 PM

Operation
80
(3) Start the engine and operate the water-craft at planing speed to drain the bilge
water from the engine compartment.
(See page 58 for information on draining
the bilge water. If the engine does not
start, see “Towing the watercraft” on
page 99 or “Submerged watercraft” on
page 99.) NOTICE: Do not run the en-
gine at full throttle for at least 1 minute
after the engine has been restarted.
Bilge water in the engine compart-
ment can splash into the engine,
which can result in severe damage.
[ECJ00554]
EJU43282
Beaching and docking the watercraft
To beach the watercraft:
(1) Make sure that there are no boats, swim- mers, or obstacles near the beach. (2) Release the throttle lever to reduce
speed about 95 m (310 ft) before you
reach the intended beaching area.
(3) Slowly approach the beach using the throttle lever and RiDE lever to control
the watercraft speed. NOTICE: Never
run the engine in water that is less
than 60 cm (2 ft) deep from the bottom
of the watercraft, otherwise pebbles
or sand could be sucked into the jet
intake, causing impeller damage and
engine overheating.
[ECJ00473]
(4) After reaching land, stop the engine, and then get off the watercraft and pull it up
on the beach.
To dock the watercraft:
(1) Make sure that there are no boats, swim-mers, or obstacles near the dock.
(2) Release the throttle lever to reduce speed about 95 m (310 ft) away from the
dock.
(3) Slowly approach the dock using the throttle lever and RiDE lever to control
the watercraft speed.
(4) After coming alongside the dock, stop the engine, and then get off the water-
craft.
EJU37194Operating in weeded areas
Always avoid using your watercraft in areas
where weed growth is thick. If operating in
weeded areas is unavoidable, alternately
squeeze the throttle lever and relax your grip
on the throttle lever to vary the engine speed.
Weeds tend to become clogged more when
operating at a steady speed and at trolling
speed. If weeds may have clogged the intake
area, clean the jet intake. (See page 97 for in-
formation on the jet intake.)
UF4S71E0.book Page 80 Wednesday, August 4, 2021 5:18 PM

Operation
81
EJU40242After removing the watercraft from
the water
ECJ01311
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
After operating and removing the watercraft
from the water, promptly discharge the re-
maining water from the cooling water pas-
sages.
To discharge water from the cooling wa-
ter passages:
(1) Make sure that the area around the wa- tercraft is clear, and then start the en-
gine.
(2) Discharge the remaining water out of the cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.
(3) Stop the engine.
UF4S71E0.book Page 81 Wednesday, August 4, 2021 5:18 PM

Trouble recovery
98
ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.
EJU43472Raising the reverse gate
If the RiDE system malfunctions and the re-
verse gate remains in the lowered position,
the watercraft will not be able to move for-
ward.
After raising the reverse gate so that the wa-
tercraft can move forward, immediately re-
turn to shore and have a Yamaha dealer
service the watercraft.
To raise the reverse gate:
(1) Stop the engine and remove the clip from the engine shut-off switch.
(2) Enter the water and move to the rear of the watercraft.
(3) Slide the shift rod joint toward the bow, and then disconnect the shift rod joint
from the ball joint.
(4) Raise the reverse gate to the forward po- sition.
TIP
While the shift rod is disconnected, the re-
verse gate will not move to the neutral po-
sition or reverse position even if the RiDE
lever is squeezed.
If the RiDE lever is squeezed while the shift
rod is disconnected, the watercraft will
move forward.
EJU34642Jumping the battery
If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.
EJU46101Connecting the jumper cablesEWJ01252
To avoid battery explosion and serious
damage to the electrical system:
Do not reverse the polarity of the jumper
cables when connecting to the batter-
ies.
Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.
Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.
1Shift rod joint
2 Ball joint
1 2
1
Reverse gate
2 Forward position
1
2
UF4S71E0.book Page 98 Wednesday, August 4, 2021 5:18 PM

101
Index
A
Accessory outlet ...................................... 45
After removing the watercraft from the water ..................................................... 81
Audio control............................................ 44
Audio system (equipped models) ............ 44
B
Battery care.............................................. 83
Battery checks ......................................... 64
Battery, jumping....................................... 98
Beaching and docking the watercraft ...... 80
Bilge water check..................................... 64
Bilge water, draining ................................ 58
Bilge water, draining on land ................... 58
Bilge water, draining on water ................. 58
Boarding alone ......................................... 76
Boarding and starting off from a dock ..... 79
Boarding the watercraft ........................... 76
Boarding with passenger(s) ..................... 77
Bow eye ................................................... 49
Bow storage compartment ...................... 50
Builder’s plate ............................................ 3
C
Capsized watercraft ................................. 79
Cleaning ................................................... 85
Cleaning the watercraft ............................ 83
Cleat ......................................................... 49
Cooling water pilot outlet ......................... 26
Cooling water pilot outlet check .............. 68
Craft Identification Number (CIN)............... 1
Cruise assist............................................. 35
Cruising limitations................................... 10
D
Display ..................................................... 37
Drive control mode................................... 33
Drive control mode screen ....................... 40
E
Emergency procedures ............................ 97
Engine break-in ........................................ 60
Engine compartment check ..................... 63
Engine cover, removing and installing ..... 87
Engine idling speed check ....................... 69
Engine lock screen ................................... 41
Engine oil ................................................. 56
Engine oil and oil filter .............................. 91 Engine oil level check ............................... 64
Engine oil requirements ........................... 56
Engine serial number ................................. 1
Engine shut-off cord (lanyard) check ....... 65
Engine shut-off switch ............................. 25
Engine start/stop switch .......................... 25
Engine unit check ..................................... 64
Enjoy your watercraft responsibly ............ 18
Equipment ................................................ 47
F
Fire extinguisher check ............................ 67
Fire extinguisher holder and cover........... 53
Fire extinguisher holder, cover, and
band checks ......................................... 66
Flushing the cooling water passages....... 82
Fuel .......................................................... 54
Fuel level check........................................ 63
Fuel requirements .................................... 54
Fuel system checks ................................. 63
G
Getting to know your watercraft .............. 70
Glossary, watercraft ................................. 19
Glove compartment ................................. 51
H
Handgrip .................................................. 48
Hazard information................................... 14
Home screen ............................................ 39
Hood check .............................................. 68
Hull and deck check ................................ 67
I
Identification numbers ............................... 1
Information screen ................................... 39
J
Jet intake and impeller, cleaning.............. 97
Jet intake checks ..................................... 67
Jet thrust nozzle and reverse gate check .................................................... 67
Jumper cables, connecting ...................... 98
L
Labels, important ....................................... 4
Labels, other .............................................. 8
Labels, warning .......................................... 5
Launching the watercraft ......................... 71
Learning to operate your watercraft......... 70
Leaving the watercraft.............................. 72
UF4S71E0.book Page 101 Wednesday, August 4, 2021 5:18 PM

Index
102
Limitations on who may operate the watercraft................................................ 9
Long-term storage ................................... 85
Lubrication ............................................... 85
M
Main components, location of ................. 20
Maintenance ............................................ 87
Manufactured date label ............................ 2
Model information ...................................... 3
Multifunction information center .............. 37
Multifunction information center check ... 68
N
No-wake mode ........................................ 32
O
Operating in weeded areas ...................... 80
Operating the watercraft .......................... 72
Operating the watercraft in reverse or neutral ................................................... 75
Operating your watercraft ........................ 70
Operation buttons .................................... 37
Operation requirements ........................... 11
P
Periodic maintenance chart ..................... 89
Post-launch checks ................................. 68
Post-operation care ................................. 82
Pre-launch checks ................................... 63
Pre-operation check points ..................... 63
Pre-operation checklist ............................ 61
Primary Identification (PRI-ID) number ...... 1
Pull-up cleats ........................................... 50
R
Raising the reverse gate .......................... 98
Reboarding grip ....................................... 48
Reboarding step ...................................... 48
Recommended equipment ...................... 13
Reverse assist .......................................... 31
RiDE lever................................................. 26
RiDE lever checks .................................... 65
Riding position ......................................... 71
Rustproofing ............................................ 86
S
Safe boating rules .................................... 17
Safety equipment check .......................... 67
Seat storage compartment ...................... 52
Seats ........................................................ 47 Setting menu screen ................................ 40
Shift system ............................................. 28
Shift system check ................................... 68
Starting off ............................................... 78
Starting off from a trailer .......................... 79
Starting the engine on water .................... 71
Steering system ....................................... 26
Steering system checks ........................... 64
Stern drain plug checks ........................... 67
Stern eyes ................................................ 49
Stopping the engine ................................. 72
Stopping the watercraft ........................... 74
Storage compartment checks.................. 66
Storage compartments ............................ 50
Submerged watercraft ............................. 99
Switch checks .......................................... 66
T
T.D.E. (thrust directional enhancer) .......... 31
Throttle lever ............................................ 25
Throttle lever checks ................................ 65
Towing the watercraft .............................. 99
Transporting on a trailer ........................... 59
Troubleshooting ....................................... 94
Troubleshooting chart .............................. 94
Turning the watercraft .............................. 73
U
USB charger............................................. 46
W
Wakeboarding and water-skiing .............. 16
Warning function ...................................... 42
Water separator ....................................... 27
Water separator check ............................. 63
Watercraft characteristics ........................ 14
Watercraft control functions..................... 24
Watercraft operation functions ................ 28
Watercraft operation modes .................... 31
Y
Yamaha Security System ......................... 24
Yamaha Security System check .............. 65
Yamaha Security System setting ............. 24
UF4S71E0.book Page 102 Wednesday, August 4, 2021 5:18 PM