weight YAMAHA WARRIOR 350 2001 User Guide

7-53
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
WARNING
Use proper gear and maintain steady speed
when climbing a hill.
If you lose all forward speed:l
Keep weight uphill.
l
Apply the brakes.
l
Lock parking brake, after you are stopped.
If you begin rolling backwards:
l
Keep weight uphill.
l
Never apply the rear brake while rolling
backwards. Apply the front brake.
When fully stopped, apply rear brake as
well, and then lock parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described in
the Owner’s Manual.

7-55
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
RIDING DOWNHILL
When riding your ATV downhill, shift your
weight as far to the rear and uphill side of the
ATV as possible. Move back on the seat and sit
with your arms straight. Choose a low gear
which will allow the engine compression to do
most of the braking for you. Improper braking
may cause a loss of traction.
Use caution while descending a hill with loose
or slippery surfaces. Braking ability and trac-
tion may be adversely affected by these surfac-
es. Improper braking may also cause a loss of
traction.
Whenever possible, ride your ATV straight
downhill. Avoid sharp angles which could al-
low the ATV to tip or roll over. Carefully choose
your path and ride no faster than you will be
able to react to obstacles which may appear.

7-57
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
WARNING
Always follow proper procedures for going
down hills as described in this Owner’s Manu-
al.
Note: a special technique is required when
braking as you go down a hill.l
Always check the terrain carefully before
you start down any hill.
l
Shift your weight backward.
l
Never go down a hill at high speed.
l
Avoid going down a hill at an angle that
would cause the vehicle to lean sharply to
one side. Go straight down the hill wherepossible.

7-59
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
CROSSING A SLOPE
Traversing a sloping surface on your ATV re-
quires you to properly position your weight to
maintain proper balance. Be sure that you
have learned the basic riding skills on flat
ground before attempting to cross a sloping
surface. Avoid slopes with slippery surfaces or
rough terrain that may upset your balance.
As you travel across a slope, lean your body in
the uphill direction. It may be necessary to cor-
rect the steering when riding on loose surfaces
by pointing the front wheels slightly uphill.
When riding on slopes be sure not to make
sharp turns either up or down hill.

7-61
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
If your ATV does begin to tip over, gradually
steer in the downhill direction if there are no
obstacles in your path. As you regain proper
balance, gradually steer again in the direction
you wish to travel.
WARNING
Never attempt to turn the ATV around on any
hill until you have mastered the turning tech-
nique as described in the Owner’s Manual on
level ground. Be very careful when turning on
any hill. Avoid crossing the side of a steep hill
if possible.
When crossing the side of a hill:l
Always follow proper procedures as de-
scribed in the Owner’s Manual.
l
Avoid hills with excessively slippery or
loose surfaces.
l
Shift your weight to the uphill side of theATV.

7-69
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
SLIDING AND SKIDDING
Care should be used when riding on loose or
slippery surfaces since the ATV may slide. If
unexpected and uncorrected, sliding could
lead to an accident.
To reduce the tendency for the front wheels to
slide in loose or slippery conditions, position-
ing your weight over the front wheels will
sometimes help.
If the rear wheels of your ATV start to slide
sideways, control can usually be regained (if
there is room to do so) by steering in the direc-
tion of the slide. Applying the brakes or accel-
erating is not recommended until you have
corrected the slide.

7-73
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
WHAT TO DO IF...
This section is designed to be a reference
guide only. Be sure to read each section on
riding techniques completely.
WHAT TO DO...l
If your ATV doesn’t turn when you want it
to:
Bring the ATV to a stop and practice the
turning maneuvers again. Be sure you are
putting your weight on the footboard to the
outside of the turn. Position your weight
over the front wheels for better control.
(See pages 7-39 ~ 7-43.)
l
If your ATV begins to tip while turning:
Lean more into the turn to regain balance. If
necessary, gradually let off the throttle
and/or steer to the outside of the turn. (See
pages 7-39 ~ 7-43.)
l
If your ATV starts to slide sideways:
Steer in the direction of the slide if you have
the room.
Applying the brakes or accelerating is not
recommended until you have corrected the
slide. (See pages 7-69 ~ 7-71.)

7-75
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
l
If your ATV can’t make it up a hill you are
trying to climb:
Turn the ATV around if you still have for-
ward speed. If not, stop, dismount on the
uphill side of the ATV and physically turn
the ATV around. If the ATV starts to slip
backwards DO NOT USE THE REAR BRAKE
- the ATV may tip over on top of you. Dis-
mount the ATV on the uphill side. (See pag-
es 7-45 ~ 7-53.)
l
If your ATV is traversing a sloping surface:
Be sure to ride with your weight positioned
towards the uphill side of the ATV to main-
tain proper balance. If the ATV starts to tip,
steer down the hill (if there are no obstacles
in your way) to regain balance. If you dis-
cover that the ATV is going to tip over, dis-
mount on the uphill side. (See pages 7-59 ~
7-61.)

10-1
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-SPEC-E.frame
EL
EBU00428
SPECIFICATIONS
MODEL YFM350X
Dimension:
Overall length
Overall width
Overall height
Seat height
Wheel base
Minimum ground clearance
Minimum turning radius1,840 mm
1,080 mm
1,080 mm
765 mm
1,200 mm
125 mm
3,500 mm
Basic weight:
With oil and full fuel tank 191 kg
Engine:
Type
Cylinder arrangement
Displacement
Bore
´
Stroke
Compression ratio
Starting system
Lubrication systemAir-cooled, 4-stroke, SOHC
Single cylinder, Forward inclined
348 cm
3


83.0
´
64.5 mm
9.2 : 1
Electric starter
Wet sump

11-1
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-11.frame
EL
EBU00429
HOW TO USE THE CONVERSION TABLE
All specification data in this manual are listed
in SI and METRIC UNITS.
Use this table to convert METRIC unit data to
IMPERIAL unit data.
Ex.
CONVERSION TABLE
METRIC MULTIPLIER IMPERIAL
**mm
´
0.03937 = **in
2 mm
´
0.03937 = 0.08 in

METRIC TO IMPERIAL
Metric unit Multiplier Imperial unit
Torquem·kg
m·kg
cm·kg
cm·kg7.233
86.794
0.0723
0.8679ft·lb
in·lb
ft·lb
in·lb
Weightkg
g2.205
0.03527lb
oz
Speed km/hr 0.6214 mph
Distancekm
m
m
cm
mm0.6214
3.281
1.094
0.3937
0.03937mi
ft
yd
in
in
Volume /
Capacitycc (cm

3

)
cc (cm

3

)
lt (liter)
lt (liter)0.03527
0.06102
0.8799
0.2199oz (IMP liq.)
cu·in
qt (IMP liq.)
gal (IMP liq.)
Misc.kg/mm
kg/cm

2

Centigrade
(

°

C)55.997
14.2234
9/5 + 32 lb/in
psi (lb/in

2

)
Fahrenheit (

°

F)