parking YAMAHA WARRIOR 350 2004 User Guide

7-27
BE CAREFUL WHERE YOU RIDE
This ATV is designed for off-road use only. Riding
on paved surfaces can cause loss of control.
WARNING
_ Always avoid paved surfaces, including side-
walks, driveways, parking lots and streets.
ATVs are designed for off-road use only.
Paved surfaces may seriously affect handling
and control of the ATV, and may cause the ve-
hicle to go out of control. _Do not ride on any public road, street, or highway.
Riding on public roads can result in collisions with
other vehicles.
WARNING
_ Never operate this ATV on any public street,
road or highway, even a dirt or gravel one. You
can collide with another vehicle. In many ar-
eas, it is illegal to operate ATVs on public
streets, roads and highways. _
U5NF63.book Page 27 Wednesday, March 12, 2003 10:06 AM

7-33
Select a large, flat area off-road to become familiar
with your ATV. Make sure that this area is free of
obstacles and other riders. You should practice
control of the throttle, brakes, shifting procedures,
and turning techniques in this area before trying
more difficult terrain. Always avoid riding on paved
surfaces: the ATV is designed for off-road use
only, and handling maneuvers are more difficult to
perform on pavement.
Set the parking brake and follow the instruction on
page 6-3 to start the engine. Once it has warmed
up you are ready to begin riding your ATV. As you
get on the ATV, be sure not to accidentally move
the shift pedal. Remember that the engine and ex-
haust pipe will be hot when riding and afterwards;
do not allow skin or clothing to come in contact
with these components.
U5NF63.book Page 33 Wednesday, March 12, 2003 10:06 AM

7-35
With the engine idling, pull the clutch lever to dis-
engage the clutch and shift into 1st gear, and then
release the parking brake. Open the throttle grad-
ually, and at the same time, release the clutch le-
ver slowly. Once the ATV has attained adequate
speed, release the throttle lever and at the same
time, quickly pull in the clutch lever and shift into
2nd gear. Open the throttle part way and gradually
release the clutch. Use this same procedure as
you move into the higher gears. Be sure to coordi-
nate the use of the throttle and shift pedal properly.
If the throttle is applied too abruptly or if the throttle
is not released during shifting, or if the shift pedal
is not released before applying the throttle, the
front wheels may lift off the ground resulting in a
loss of directional control. Avoid higher speeds un-
til you are thoroughly familiar with the operation of
your ATV.
WARNING
_ Always open the throttle gradually and release
the clutch lever slowly. Otherwise, the ATV
could wheelie which would increase the
chance of an accident. _
U5NF63.book Page 35 Wednesday, March 12, 2003 10:06 AM

7-53
WARNING
_ Use proper gear and maintain steady speed
when climbing a hill.
If you lose all forward speed:

Keep weight uphill.


Apply the brakes.


Lock the parking brake, after you are
stopped.
If you begin rolling backwards:


Keep weight uphill.


Never apply the rear brake while rolling
backwards. Apply the front brake.
When fully stopped, apply the rear brake
as well, and then lock the parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described in
the Owner’s Manual.
_
U5NF63.book Page 53 Wednesday, March 12, 2003 10:06 AM

8-53 A. Cable length
A. Longueur de câble
A. Longitud del cable
EBU01192
Parking brake adjustment
Parking brake adjustment may be required if the
parking brake does not hold properly. The cable
length
A should be adjusted to 46–50 mm.
1. Fully loosen the locknut and the adjusting bolt
at the clutch lever.
2. Loosen the locknut and the adjusting bolt at
the rear brake caliper.
3. Turn the adjusting bolt at the clutch lever in
direction
a to increase the cable length or in
direction
b to decrease the cable length.NOTE:_ If the cable cannot be adjusted to specification,
consult a Yamaha dealer. _
U5NF63.book Page 53 Wednesday, March 12, 2003 10:06 AM

8-55 1. Locknut 2. Adjusting bolt
1. Contre-écrou 2. Boulon de réglage
1. Contratuerca 2. Perno de ajuste
1. Locknut 2. Adjusting bolt
1. Contre-écrou 2. Boulon de réglage
1. Contratuerca 2. Perno de ajuste
4. Tighten the locknut at the clutch lever.
5. Screw in the adjusting bolt at the rear brake
caliper by hand until it feels tight, then screw it
out 1/8 turn. Tighten the locknut to the speci-
fied torque.CAUTION:_ When tightening the locknut, hold the adjust-
ing bolt with a wrench so that the adjusting
bolt does not turn together with the locknut. _
WARNING
_ Operating with improperly adjusted brakes
could cause the brakes to malfunction, result-
ing in reduced braking performance. This
could increase the chance of a collision or ac-
cident. After adjusting the parking brake, block
the rear of the machine off the ground and spin
the rear wheels. Check to make sure there is
no brake drag. If brake drag is noticed, perform
the adjustment again. _
Tightening torque:
Locknut:
16 Nm (1.6 m·kgf)
U5NF63.book Page 55 Wednesday, March 12, 2003 10:06 AM