wheel YAMAHA WOLVERINE 2017 Owner's Guide

8-45
8
EBU32610Wheel removal1. Loosen the wheel nuts.
2. Elevate the vehicle and place a suitablestand under the frame.
3. Remove the nuts from the wheel.
4. Remove the wheel.
EBU32620Tire replacementAlways use the same size and type of tires
recommended in this owner’s manual. The
tires that came with your Yamaha Wolverine
were designed to match the performance ca-
pabilities and to provide the best combination
of handling, braking, and comfort. It is best to
replace all four tires at the same time. If that is
not possible, you must replace the tires in1. Wheel nut
1
1
U2MB7BE0.book Page 45 Thursday, March 3, 2016 11:46 AM

8-46
8
pairs (front or rear) with tires of the same size
and type as the originals. Never replace just
one tire.
WARNING
EWB03390Installing improper tires on your Yamaha
Wolverine can affect handling and stabili-
ty. This can cause a loss of control. The tires listed below have been approved by
Yamaha Motor Manufacturing Corporation of
America for this model.
EBU33030Wheel installation1. Install the wheel and the nuts.TIPFor YXE70WPXH / YXE70WPHH: tapered
nuts are used for both the front and rear
wheels. Install the nuts with their tapered side
towards the wheel. 2. Lower the vehicle so that the wheel is on the ground.
3. Tighten the wheel nuts in a crisscross pattern to the specified torque.
Front tire:Size:26 x 8-12NHS
Manufacturer/model: MAXXIS/MU09
Rear tire: Size:26 x 10-12NHS
Manufacturer/model: MAXXIS/MU10
1. Tapered nut
1
U2MB7BE0.book Page 46 Thursday, March 3, 2016 11:46 AM

8-47
8
WARNING
EWB03400Do not reverse the rims on your Yamaha
Wolverine to widen the track width. Install-
ing wheels improperly increases the risk of
wheel failure and accidents. EBU32640BatteryThe battery is located under the hood. (See
page 8-10 for hood removal and installation
procedures.)
This model is equipped with a VRLA (Valve
Regulated Lead Acid) battery. There is no
need to check the electrolyte or to add dis-
tilled water. However, the battery lead con-
nections need to be checked and, if
necessary, tightened.
WARNING
EWB03410Avoid battery contact with skin, eyes, or
clothing. Shield eyes when working near
batteries. Keep out of reach of children.
You could be poisoned or severely burned
by the sulfuric acid in battery electrolyte. In
case of accidental contact with battery
electrolyte:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water
or milk. Follow with milk of magnesia,
beaten egg, or vegetable oil. Get prompt
medical attention.
EYES: Flush with water for 15 minutes and
get prompt medical attention.
Tightening torques:Front wheel nut:75 N·m (7.5 kgf·m, 54 lb·ft)
Rear wheel nut: 75 N·m (7.5 kgf·m, 54 lb·ft)
U2MB7BE0.book Page 47 Thursday, March 3, 2016 11:46 AM

8-53
8
If a fuse is blown, replace it as follows.1. Turn the key to “ ” (off) and turn off the
electrical circuit in question.
NOTICEECB00641To prevent accidental short-circuiting,
turn off the main switch when checking or
replacing a fuse. 2. Remove the hood. (See page 8-10 forhood removal and installation proce-
dures.)
3. Remove the blown fuse, and then install a new fuse of the specified amperage.
WARNING! Always use a fuse of the specified amperage. Never use any
material in place of the proper fuse.
Using an improper fuse can cause
damage to the electrical system and
may lead to a fire.
[EWB03440]
1. Backup fuse “BACK UP” (for clock)
2. Ignition fuse “IGNITION”
3. Four-wheel-drive motor fuse “DIFF”
4. Auxiliary DC jack fuse “TERMINAL”
5. Signaling system fuse “SIGNAL”
6. Headlight fuse “HEAD”
7. Spare fuse
8. Radiator fan motor fuse “FAN”
1
2
3
4
5
6
8
7
7
U2MB7BE0.book Page 53 Thursday, March 3, 2016 11:46 AM

8-54
8
4. Turn the key to “ ” (on) and turn on theelectrical circuit in question to check if
the device operates. If the fuse blows
again immediately, have a Yamaha dealer
check the electrical system.
5. Install the hood.EBU32670Replacing a headlight bulbIf a headlight bulb burns out, replace it as fol-
lows. 1. Remove the cover at the rear of the head- light by pulling it off.
Specified fuses:Main fuse:40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Signaling system fuse: 10.0 A
Four-wheel-drive motor fuse: 10.0 A
Radiator fan motor fuse: 25.0 A
Backup fuse: 10.0 A
EPS fuse: 40.0 A
1. Cover at the rear of the headlight
1
U2MB7BE0.book Page 54 Thursday, March 3, 2016 11:46 AM

9-1
9
EBU32720
CLEANING AND STORAGE
EBU33681CleaningFrequent, thorough cleaning of your vehicle
will not only enhance its appearance but will
improve its general performance and extend
the useful life of many components.1. Before cleaning the vehicle: a. Block off the end of the exhaust pipeto prevent water entry. A plastic bag
and strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do
not apply degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure
to do the job. WARNING! Test the
brakes after washing. Apply the
brakes several times at slow speeds to
let friction dry the brakes. Wet brakes may have reduced stopping ability, in-
creasing the chance of an accident.
[EWB03471]

NOTICE: Excessive water pres-
sure may cause water seepage and
deterioration of wheel bearings,
brakes, transmission seals and electri-
cal devices. Many expensive repair
bills have resulted from improper high-
pressure detergent applications such
as those available in coin-operated car
washers.
[ECB00712]
TIPThe tailgate can be removed to make it easier
to clean the cargo bed. To separate the tail-
gate from the cargo bed, unhook the latches,
and then pull up the tailgate. (See page 4-21
for tailgate removal and installation proce-
dures.)
U2MB7BE0.book Page 1 Thursday, March 3, 2016 11:46 AM

9-3
9
Remove the spark plug wire and ground
it. Operate the electric starter to turn the
engine over several times and coat the
cylinder walls with oil.
3. Lubricate all control cables.
4. Put the frame on stands or blocks to raise
all wheels off the ground.
5. Tie a plastic bag over the exhaust pipe
outlet to prevent moisture from entering.
6. If storing in a humid or salt-air atmo- sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat covers.
7. Remove the battery and charge it. Store
it in a dry place and recharge it once a
month. Do not store the battery in an ex-
cessively warm or cold place [less than 0
°C (30 °F) or more than 30 °C (90 °F)].
Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha
dealer if the fuel system needs to be drained.
U2MB7BE0.book Page 3 Thursday, March 3, 2016 11:46 AM

10-1
10
EBU32750
SPECIFICATIONS
Dimensions:Overall length:2970 mm (116.9 in)
Overall width: 1540 mm (60.6 in)
Overall height:
1885 mm (74.2 in)
Wheelbase: 2065 mm (81.3 in)
Ground clearance: 290 mm (11.4 in)
Minimum turning radius:
4600 mm (181 in)Weight:Curb weight:595.0 kg (1312 lb)Noise and vibration level:Noise level (77/311/EEC):80.0 dB(A) at 3125 r/min (YXE70WPAH, YXE70WPXH)
Uncertainty of measurement: 3.0 dB(A) (YXE70WPAH, YXE70WPXH)
Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s² (YXE70WPAH, YXE70WPXH)
Uncertainty of measurement: 0.0 m/s² (YXE70WPAH, YXE70WPXH)
Vibration on handle (EN1032, ISO5008): Will not exceed 2.5 m/s² (YXE70WPAH, YXE70WPXH) Uncertainty of measurement:
0.5 m/s² (YXE70WPAH, YXE70WPXH)
Engine:Engine type:Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
Single cylinder
Displacement: 708 cm³
Bore × stroke:
103.0 × 85.0 mm (4.06 × 3.35 in)
Compression ratio:
10.1 : 1
Starting system: Electric starter
Lubrication system: Wet sumpEngine oil:Recommended brand:YAMALUBE
U2MB7BE0.book Page 1 Thursday, March 3, 2016 11:46 AM

10-3
10
Secondary reduction ratio:43/21 × 17/12 × 33/9 (10.636)
Transmission type: V-belt automatic
Operation:
Right hand operation
Reverse gear: 23/14 × 28/23 (2.000)
Low range: 31/16 (1.938)
High range:
30/22 (1.364)Chassis:Frame type:Steel tube frame
Caster angle:
3.70 °
Trail: 19.0 mm (0.75 in)Front tire:Type:
Tubeless
Size: 26 x 8-12NHS
Manufacturer/model: MAXXIS/MU09Rear tire:Type:Tubeless
Size: 26 x 10-12NHS Manufacturer/model:
MAXXIS/MU10
Loading:Maximum loading limit:
327.0 kg (721 lb)
(Total weight of operator, passengers, cargo, accessories,
and tongue)Tire air pressure (measured on cold tires):Recommended:
Vehicle load: 0 - maximum
Front:
75.0 kPa (0.750 kgf/cm², 11 psi)
Rear: 75.0 kPa (0.750 kgf/cm², 11 psi)
Minimum: Vehicle load: 0 - maximum
Front: 70.0 kPa (0.700 kgf/cm², 10 psi)
Rear:
70.0 kPa (0.700 kgf/cm², 10 psi)Front wheel:Wheel type:Cast wheel (YXE70WPAH)
Panel wheel (YXE70WPHH, YXE70WPXH)
Rim size: 12 x 6.0AT
U2MB7BE0.book Page 3 Thursday, March 3, 2016 11:46 AM

10-4
10
Rear wheel:Wheel type:Cast wheel (YXE70WPAH)
Panel wheel (YXE70WPHH, YXE70WPXH)
Rim size: 12 x 7.5ATFront brake:Type:Hydraulic disc brake
Operation: Unified brake
Specified brake fluid:
DOT 4Rear brake:Type:Hydraulic disc brake
Operation:
Unified brake
Specified brake fluid: DOT 4Front suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel: 246 mm (9.7 in)Rear suspension:Type:Double wishbone Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel: 269 mm (10.6 in)
Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:U1-H11L
Voltage, capacity: 12 V, 28.0 AhHeadlight(s):Bulb type:Halogen bulbBulb voltage, wattage × quantity:Headlight:
12 V, 35.0/35.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 2
Neutral indicator light: LED
Reverse indicator light:
LED
Coolant temperature warning light: LED
Engine trouble warning light: LED
U2MB7BE0.book Page 4 Thursday, March 3, 2016 11:46 AM