check oil YAMAHA WOLVERINE 2018 User Guide

8-14
8
EBU33706Engine oil and oil filter cartridgeCheck the engine oil level before each opera-
tion. In addition, change the oil and the oil fil-
ter cartridge at the intervals specified in the
periodic maintenance chart.NOTICEECB00301 In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do
not use oils with a diesel specification of
“CD” or oils of a higher quality than
specified. In addition, do not use oils la-
beled “ENERGY CONSERVING II” or
higher. 
Make sure that no foreign material en-
ters the crankcase.
To check the engine oil level
1. Park the vehicle on a level surface.
2. Check the engine oil level on a cold en-
gine.TIPIf the engine was started before checking the
oil level, be sure to warm up the engine suffi-
ciently, and then wait at least 10 minutes until
the oil settles for an accurate reading. 3. Remove the passenger seat cushion.(See page 4-15.)
4. Remove the rubber cover.
Recommended engine oil: See page 10-1.
Oil quantity: Oil change only:2.20 L (2.33 US qt, 1.94 Imp.qt)
When replacing the filter: 2.30 L (2.43 US qt, 2.02 Imp.qt)
UB3D7AE0.book Page 14 Tuesday, November 7, 2017 9:38 AM

8-15
8
5. Remove the engine oil dipstick and wipeit with a clean rag. 6. With the arrow mark pointing in the direc-
tion shown, insert the dipstick completely
into the oil filler tube and then remove it
again to check the oil level.1. Rubber cover
1
1. Engine oil dipstick
2. Maximum level mark
3. Minimum level mark
2
31
UB3D7AE0.book Page 15 Tuesday, November 7, 2017 9:38 AM

8-20
8
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down. 14. Start the engine, and then let it idle forseveral minutes while checking it for oil
leakage. If oil is leaking, immediately turn
the engine off and check for the cause.
15. Turn the engine off, wait at least 10 minu-
tes, and then check the oil level and cor-
rect it if necessary.
16. Install the rubber cover.
17. Install the passenger seat cushion.EBU36051Final gear oilCheck the oil level and change the final gear
oil at the intervals specified in the general
maintenance and lubrication chart.
NOTICEECB03590When checking or changing the final gear
oil, make sure that no foreign material en-
ters the final gear case. If necessary, clean
the final gear oil filler bolt and surrounding
area. Checking the final gear oil level 1. Park the vehicle on a level surface.
2. Remove the final gear oil filler bolt and its
gasket, and then check the oil level in the
final gear case. The oil level should be at
the brim of the filler hole.
Recommended oil:SAE 80 API GL-4 Hypoid gear oil
Oil quantity: 0.64 L (0.68 US qt, 0.56 Imp.qt)
UB3D7AE0.book Page 20 Tuesday, November 7, 2017 9:38 AM

8-21
8
3. If the oil is below the brim of the filler hole,add sufficient oil of the recommended
type to raise it to the correct level.
4. Check the gasket for damage, and re- place it if necessary.
5. Install the oil filler bolt and its gasket, and
then tighten the bolt to the specified
torque. Changing the final gear oil
1. Park the vehicle on a level surface.
2. Place an oil pan under the final gear case
to collect the used oil.
3. Remove the final gear oil filler bolt, the fi-
nal gear oil drain bolt and their gasket to
drain the oil.1. Final gear oil
2. Gasket
3. Final gear oil filler bolt
4. Correct oil level
24
3
1
Tightening torque:Final gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)1. Final gear oil drain bolt
2. Gasket
21
UB3D7AE0.book Page 21 Tuesday, November 7, 2017 9:38 AM

8-22
8
4. Install the drain bolt and its new gasket,and then tighten the bolt to the specified
torque.
5. Refill with the recommended final gear oil up to the brim of the filler hole.TIPGL-4 is a quality and additive rating; GL-5
rated hypoid gear oils may also be used.
 If desired, an SAE 80W-90 hypoid gear oil
may be used instead. 6. Check the oil filler bolt gasket for dam-
age, and replace it if necessary.
7. Install the oil filler bolt and its gasket, and then tighten the bolt to the specified
torque. 8. Check for oil leakage. If oil leakage is
found, check for the cause.
EBU36061Differential gear oilCheck the oil level and change the differential
gear oil at the intervals specified in the gener-
al maintenance and lubrication chart.NOTICEECB03600When checking or changing the differen-
tial gear oil, make sure that no foreign ma-
terial enters the differential gear case. If
necessary, clean the differential gear oil
filler bolt and surrounding area.
Tightening torque:Final gear oil drain bolt:22 N·m (2.2 kgf·m, 16 lb·ft)
Tightening torque: Final gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
Recommended oil: SAE 80 API GL-4 Hypoid gear oil
Oil quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)
UB3D7AE0.book Page 22 Tuesday, November 7, 2017 9:38 AM

8-23
8
Checking the differential gear oil level1. Park the vehicle on a level surface.
2. Remove the differential gear oil filler bolt
and its gasket, and then check the oil lev-
el. It should be up to the brim of the filler
hole.
3. If the level is low, add sufficient oil of the recommended type to raise it to the
specified level. 4. Check the gasket for damage, and re-
place it if necessary.
5. Install the differential gear oil filler bolt and its gasket, and then tighten the bolt
to the specified torque.
Changing the differential gear oil 1. Park the vehicle on a level surface.
2. Place an oil pan under the differential gear case to collect the used oil.
3. Remove the differential gear oil filler bolt, the differential gear oil drain bolt and their
gasket to drain the oil.1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil level
1
2
3
4
Tightening torque:Differential gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
UB3D7AE0.book Page 23 Tuesday, November 7, 2017 9:38 AM

8-24
8
4. Install the differential gear oil drain boltand its new gasket, and then tighten the
bolt to the specified torque.
5. Refill the differential gear case with the recommended oil.
TIPGL-4 is a quality and additive rating; GL-5
rated hypoid gear oils may also be used.
 If desired, an SAE 80W-90 hypoid gear oil
may be used instead. 6. Check the oil filler bolt gasket for dam-
age, and replace it if necessary.
7. Install the differential gear oil filler bolt and its gasket, and then tighten the bolt
to the specified torque.
8. Check for oil leakage. If oil leakage is found, check for the cause.
1. Differential gear oil drain bolt
2. GasketTightening torque:Differential gear oil drain bolt:9.8 N·m (0.98 kgf·m, 7.2 lb·ft)
12
Tightening torque: Differential gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
UB3D7AE0.book Page 24 Tuesday, November 7, 2017 9:38 AM

8-36
8
11. Thoroughly apply Yamaha foam air filteroil or other quality liquid foam air filter oil
(not spray type) to the sponge material.
The sponge material should be wet but
not dripping.
12. Pull the sponge material over its frame.
13. Install the air filt er element holder.
14. Install the air filter element.
15. Install the air filter case cover by fitting the
pivot holders onto the projections on the
air filter case, and th en close and lock the
cover in place with the snap holders. 16. Install the storage compartment as
shown.
EBU33673Air filter check hosesThere is a check hose at the bottom of the air
filter case and at the bottom of the air intake
duct. If dust or water collects in a check hose,
the air filter element may be soiled. Clean the
check hose, air filter element and air filter
case.
1. Pivot holder
2. Projection
1
2
UB3D7AE0.book Page 36 Tuesday, November 7, 2017 9:38 AM

8-41
8
Clean the filler cap before removing. Use
only DOT 4 brake fluid from a sealed
container.
 Use only the specified brake fluid; other-
wise, the rubber seals may deteriorate,
causing leakage.
 Refill with the same type of brake fluid.
Adding a brake fluid other than DOT 4
may result in a harmful chemical reac-
tion.
 Be careful that water does not enter the
brake fluid reservoir when refilling. Wa-
ter will significantly lower the boiling
point of the fluid and may result in vapor
lock. NOTICEECB01161Brake fluid may damage painted surfaces
or plastic parts. Always clean up spilled
fluid immediately.
As the brake pads wear, it is normal for the
brake fluid level to gradually go down. A low
brake fluid level may indicate worn brake
pads and/or brake system leakage; therefore,
be sure to check the brake pads for wear and
the brake system for leakage. If the brake fluid
level goes down suddenly, have a Yamaha
dealer check and repair the vehicle before
any further operation.EBU32520Brake fluid replacementComplete fluid replacement should be done
only by trained Yamaha service personnel.
Have a Yamaha dealer replace the following
components during periodic maintenance or
when they are damaged or leaking.
Replace the oil seals every two years.
 Replace the brake hoses every four years.
UB3D7AE0.book Page 41 Tuesday, November 7, 2017 9:38 AM

12-1
12
INDEX
AAccelerator pedal ......................................................... 4-12
Accelerator pedal, Pre-operation check ........................ 5-6
Air filter check hoses .................................................... 8-36
Air filter element, cleaning ............................................ 8-32
Auxiliary DC jack .......................................................... 4-33
Axle boots .................................................................... 8-29BBasic guide for safe use ................................................. 7-1
Battery, Periodic maintenance ..................................... 8-47
Brake fluid level, checking ........................................... 8-40
Brake fluid, replacing ...................................................8-41
Brake light switch, adjusting ........................................ 8-42
Brake pedal .................................................................. 4-13
Brake pedal and accelerator pedal, lubrication ........... 8-43
Brake pedal, checking ................................................. 8-42
Brakes, Periodic maintenance ..................................... 8-39
Brakes, Pre-operation check ......................................... 5-3CCable, inspecting and lubrication ................................ 8-43
Cargo bed .................................................................... 4-20
Cleaning ......................................................................... 9-1
Control cables, Pre-operation check ............................. 5-8
Coolant, Periodic maintenance .................................... 8-25
Coolant, Pre-operation check ........................................ 5-6
Coolant temperature warning light ................................. 4-4
Cup holders .................................................................. 4-20DDifferential gear lock indicator light ............................... 4-3Differential gear oil, Periodic maintenance .................. 8-22
Differential gear, Pre-operation check ........................... 5-6
Doors ........................................................................... 4-14
Driver seat position ...................................................... 4-16
Drive select lever .......................................................... 4-14
Drive select lever operation and reverse driving ............ 6-3
Drivetrain icon ................................................................ 4-3
EEngine break-in .............................................................. 6-1
Engine oil and oil filter cartridge, Periodic
maintenance .............................................................. 8-14
Engine oil, Pre-operation check ..................................... 5-5
Engine trouble warning light .......................................... 4-4
EPS warning light ........................................................... 4-5FFinal gear oil, Periodic maintenance ............................ 8-20
Final gear, Pre-operation check ..................................... 5-6
Fittings and fasteners, Pre-operation check .................. 5-7
Four–wheel drive knob (On–Command 4WD) .............. 4-11
Front and rear brake pads, checking ........................... 8-39
Fuel, Pre-operation check .............................................. 5-3
Fuel tank cap ............................................................... 4-14
Fuse, replacing ............................................................. 8-52GGlove compartment ..................................................... 4-18HHeadlight beam, adjusting ........................................... 8-56
Headlight bulb, replacing ............................................. 8-54
Helmet indicator light ..................................................... 4-5
High-range indicator light .............................................. 4-2
Hood ............................................................................ 8-10
UB3D7AE0.book Page 1 Tuesday, November 7, 2017 9:38 AM