lock YAMAHA WR 125R 2009 User Guide

PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
61. Remove the headlight cowling to-
gether with the headlight unit by
removing the bolts and pulling up-
ward as shown.
2. Disconnect the headlight coupler,
and then remove the bulb cover.3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.
5. Install the headlight bulb cover,
and then connect the coupler.
6. Install the headlight cowling (to-
gether with the headlight unit) by
placing it in the original position,
and then installing the bolts.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAUM2610
Replacing a tail/brake light
bulb 1. Remove panel B. (See page 6-7.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the panel.
1. Bolt
1. Headlight coupler
2. Bulb cover
1
1
1. Headlight bulb holder
1. Tail/brake light bulb socket
U22BE0E0.book Page 30 Wednesday, December 17, 2008 11:00 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
6
EAU24204
Replacing a turn signal light
bulb 1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]EAUM2620
Replacing the license plate
light bulb 1. Remove panel B. (See page 6-7.)
2. Remove the socket (together with
the bulb) by pulling it out.
3. Remove the burnt-out bulb by pull-
ing it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by pushing it in.
6. Install the panel.
EAU45222
Replacing an auxiliary light
bulb If the auxiliary light bulb burns out, re-
place it as follows.
1. Remove the headlight unit. (See
page 6-29.)
2. Remove the auxiliary light socket
(together with the bulb) by pulling it
out.
3. Remove the burnt-out bulb by pull-
ing it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket (to-
gether with the bulb) by pushing it
in.
6. Install the headlight unit.
1. Screw
2. Turn signal light lens
1. License plate light bulb
1. Auxiliary light bulb
U22BE0E0.book Page 31 Wednesday, December 17, 2008 11:00 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
6
EAU25080
Rear wheel
EAUM2661
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of itfalling over.
1. Loosen the locknut and drive chain
slack adjusting nut on each side of
the swingarm.
2. Loosen the axle nut.3. Lift the rear wheel off the ground
according to the procedure on
page 6-32.
4. Remove the axle nut and the left
drive chain alignment plate.
5. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
TIP

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.


The drive chain does not need to
be disassembled in order to re-move and install the rear wheel.
6. While supporting the brake caliper
and slightly lifting the wheel, pull
the wheel axle out together with
the right drive chain alignment
plate.
TIPA rubber mallet may be useful to tap thewheel axle out.
7. Remove the wheel. NOTICE: Do
not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.
[ECA11071]
EAUM2652
To install the rear wheel
1. Install the drive chain onto the rear
sprocket.
1. Axle nut
2. Drive chain slack adjusting nut
3. Locknut
1. Wheel axle
U22BE0E0.book Page 34 Wednesday, December 17, 2008 11:00 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
6Engine overheating
WARNING
EWA10400


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissingsound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U22BE0E0.book Page 38 Wednesday, December 17, 2008 11:00 AM

INDEXAAir filter element and check hose,
replacing and cleaning........................ 6-13
Auxiliary light bulb, replacing ................ 6-31BBattery................................................... 6-27
Brake and clutch levers, checking and
lubricating ........................................... 6-24
Brake fluid, changing ............................ 6-21
Brake fluid level, checking .................... 6-20
Brake lever .............................................. 3-6
Brake pedal ............................................. 3-7
Brake pedal, checking and
lubricating ........................................... 6-25
Brake pedal free play, adjusting............ 6-19CCables, checking and lubricating .......... 6-23
Care ........................................................ 7-1
Catalytic converters ................................ 3-9
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-18
Coolant.................................................. 6-12
Coolant temperature warning light .......... 3-2DDimmer switch ........................................ 3-5
Drive chain, cleaning and lubricating .... 6-23
Drive chain slack ................................... 6-21EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-14
Engine oil and oil filter element ............... 6-9
Engine stop switch .................................. 3-5
Engine trouble warning light.................... 3-3
FFront and rear brake pads, checking .... 6-19
Front brake lever free play, checking ... 6-19
Front fork, checking .............................. 6-26
Fuel......................................................... 3-8
Fuel consumption, tips for reducing........ 5-3
Fuel tank cap .......................................... 3-7
Fuses, replacing ................................... 6-29HHandlebar switches ................................ 3-5
Headlight bulb, replacing ...................... 6-29
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-12
Indicator and warning lights .................... 3-2KKey identification number ....................... 9-1LLicense plate light bulb, replacing ........ 6-31MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Model label ............................................. 9-2
Multi-function display .............................. 3-3NNeutral indicator light .............................. 3-2PPanels, removing and installing .............. 6-7
Parking ................................................... 5-4
Part locations .......................................... 2-1
Pass switch............................................. 3-5
SSafety information ................................... 1-1
Seat ....................................................... 3-10
Shifting .................................................... 5-2
Shift pedal ............................................... 3-6
Shock absorber assembly, adjusting .... 3-10
Sidestand .............................................. 3-11
Sidestand, checking and lubricating...... 6-25
Spark plug, checking ............................... 6-8
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch.............................................. 3-5
Steering, checking................................. 6-26
Storage.................................................... 7-3
Supporting the motorcycle .................... 6-32
Swingarm pivots, lubricating ................. 6-25TTail/brake light bulb, replacing .............. 6-30
Throttle cable free play, adjusting ......... 6-14
Throttle grip and cable, checking and
lubricating ........................................... 6-24
Tires ...................................................... 6-15
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-35
Troubleshooting charts.......................... 6-37
Turn signal indicator light ........................ 3-2
Turn signal light bulb, replacing ............ 6-31
Turn signal switch ................................... 3-5VValve clearance..................................... 6-15
Vehicle identification number .................. 9-1WWheel bearings, checking ..................... 6-27
Wheel (front) ......................................... 6-32
U22BE0E0.book Page 1 Wednesday, December 17, 2008 11:00 AM