light YAMAHA WR 250F 2001 User Guide

SPEC
2 - 16
MAINTENANCE SPECIFICATIONS
NOTE:
- marked portion shall be checked for torque tightening after break-in or before each race. Headlight stay (lower) and lower bracket M6 ´ 1.0 2 7 0.7 5.1
Headlight (left and right) M6 ´ 1.0 2 10 1.0 7.2
Headlight (lower) M6 ´ 1.0 1 7 0.7 5.1
Taillight M6 ´ 1.0 3 4 0.4 2.9
Taillight lead clamp and rear fender M4 ´ 1.59 2 1 0.1 0.7
Coolant reservoir M6 ´ 1.0 2 7 0.7 5.1
Sidestand bracket and frame M10 ´ 1.25 2 64 6.4 46
Sidestand M10 ´ 1.25 1 64 6.4 46 Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb

SPEC
2 - 17
MAINTENANCE SPECIFICATIONS
EC212300
ELECTRICAL
Item Standard Limit
Ignition system:
Advancer type Electrical ----
CDI:
Magneto-model/manufacturer F5NG 00/YAMAHA----
Charging coil 1 resistance (color) 640 ~ 960 W at 20 ˚C (68 ˚F)
(Green – Brown)----
Charging coil 2 resistance (color) 464 ~ 696 W at 20 ˚C (68 ˚F)
(Green – Pink)----
Lighting coil resistance (color) 0.16 ~ 0.24 W at 20 ˚C (68 ˚F)
(Black – Yellow)----
Pickup coil resistance (color) 248 ~ 372 W at 20 ˚C (68 ˚F)
(White – Red)----
CDI unit-model/manufacturer 5PH-00/YAMAHA ----
Ignition coil:
Model/manufacturer 4SR-00/YAMAHA ----
Minimum spark gap 6 mm (0.24 in) ----
Primary coil resistance 0.20 ~ 0.30 W at 20 ˚C (68 ˚F) ----
Secondary coil resistance 9.5 ~ 14.3 kW at 20 ˚C (68 ˚F) ----
Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Stator M6 ´ 1.0 3 10 1.0 7.2
Rotor M10 ´ 1.25 1 48 4.8 35
Neutral switch M5 ´ 0.8 2 4 0.4 2.9
Ignition coil M6 ´ 1.0 2 7 0.7 5.1

2 - 19
SPEC

CABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1
Hose guide
2
Brake hose
3
Voltage regulator
4
Light switch lead
5
Fuel tank breather hose
6
Clamp
7
Oil tank breather hose
8
Engine stop switch lead
9
Sub-wire harness
0
Taillight lead
A
Throttle position sensor lead
B
Neutral switch lead
C
Oil hose
D
Cylinder head breather hose
E
CDI magneto lead
F
Clutch cable
G
Cable guide
H
Carburetor breather hose
I
Carburetor overflow hose
J
Coolant reservoir breather hose
K
Decompression cable
L
CDI unit lead
M
Ignition coil lead
N
Voltage regulator lead

Pass the fuel tank breather hose
behind handlebar, then insert it
into the steering stem hole.
õ
Pass the decompression cable,
engine stop switch lead and light
switch lead under where the oil
hose is attached.
‚
Pass the voltage regulator lead,
engine stop switch lead and light
switch lead over the radiator
hose.
ë
Fasten the engine stop switch
lead and ignition coil lead of the
sub-wire harness.
ä
Fasten the sub-wire harness
and engine stop switch lead.
ì
Pass the cylinder head breather
hose along the right side of the
oil tank breather hose.
í
Fasten the sub-wire harness
and engine stop switch lead in
front of the upper engine brack-
ets.
î
Fasten the sub-wire harness.
é
Pass the sub-wire harness
between the upper engine
brackets.
ï
Fasten the sub-wire harness.
ð
Fasten the throttle position sen-
sor lead.

2 - 20
SPEC

CABLE ROUTING DIAGRAM
ñ
Pass the carburetor breather
hose and overflow hose
between the connecting rod
and cross tube (frame).
÷
Pass the cylinder head
breather hose through the hose
guide.
ö
Pass the clutch cable through
the cable guide.
¯
Fasten the neutral switch lead
and CDI magneto lead.
¸
Pass the clutch cable along the
inner side of the cylinder head
breather hose.
Î
Pass the cylinder head
breather hose along the inner
side of the radiator hose.
å
Pass the clutch cable in front of
the radiator mounting boss.
ê
Fit the brake hose into the
guides on the protector.
æ
Fasten the ground lead
together with the ignition coil
lead.
è
Do not allow the engine stop
switch leads and light switch
lead to slacken between the
two clamps.
×
Pass the decompression cable
along the right side of the cylin-
der head breather hose.
ã
Pass the clutch cable through
the cable guides.
ô
Pass the carburetor breather
hoses and overflow hose so
that all there hoses do not con-
tact the rear shock absorber.
ç
Position each lead at the lower
left of the main tube (frame).

2 - 22
SPEC
1Coolant reservoir hose
2Coolant reservoir breather hose
3Clamp
4Taillight lead
5Hose guideFasten the coolant reservoir hose and coolant
reservoir breather hose.
õDo not allow the taillight lead to slacken.
‚Pass the coolant reservoir hose and coolant res-
ervoir breather hose through the hose guide.
CABLE ROUTING DIAGRAM

2 - 23
SPECCABLE ROUTING DIAGRAM
1Brake hose
2Brake hose holder
3Brake master cylinderInstall the brake hose to the brake caliper with the
paint on the pipe facing the brake caliper and with
the pipe contacting the brake caliper projection.
õPass the brake hose into the brake hose holders.
‚If the brake hose contacts the spring (rear shock
absorber), correct its twist.
ëInstall the brake hose so that its pipe portion
directs as shown and lightly touches the projection
on the brake master cylinder.
A
A 2
3
1
12
3 ë
‚
õ

2 - 24
SPECCABLE ROUTING DIAGRAM
1Throttle cable
2Light switch
3Light switch lead
4Clamp
5Decompression cable
6Clutch cable
7Hose guide
8Trip meter
9Brake hose
0Engine stop switch leadFasten the engine stop switch lead to the handlebar with the plastic
band.
õPass the decompression cable between the brake hose and clutch
cable.
‚Pass the throttle cables between the upper bracket and trip meter.
ëPass the light switch leads behind the engine stop switch lead, then
pass the headlight lead (of the light switch leads) in front of the head
pipe.
äInstall the trip meter cable so that its bent portion faces the chassis
rear.
ìInstall the brake hose so that it contacts the master cylinder projec-
tion and that its bent portion faces downward.

3 - 12
INSP
ADJ
AIR FILTER CLEANING
2. Adjust:
lDecompression lever free play
Adjustment steps:
lLoosen the locknut 1.
lTurn the adjuster 2 in or out until the
adjustment is suitable.
lTighten the locknut.
CAUTION:
After the adjustment, start the engine
and make sure that the engine does not
stop when the handlebar is turned fully
both ways. If the decompression cable is
too tense, the engine will stop by the
decompression system.
AIR FILTER CLEANING
NOTE:
Proper air filter maintenance is the biggest key
to preventing premature engine wear and
damage.
CAUTION:
Never run the engine without the air filter
element in place; this would allow dirt and
dust to enter the engine and cause rapid
wear and possible engine damage.
1. Remove:
lSeat
2. Disconnect:
lTaillight lead connectors 1
3. Remove:
lAir filter case cover 2
4. Remove:
lFitting bolt 1
lWasher 2
lAir filter element 3
lAir filter guide 4

3 - 14
INSP
ADJ
10. Install:
lAir filter element 1
lWasher
lFitting bolt
NOTE:
Align the projection a on filter guide with the
hole b in air filter case.
T R..2 Nm (0.2 m · kg, 1.4 ft · lb)
ENGINE OIL LEVEL INSPECTION
1. Start the engine, warm it up for several
minutes, and then turn off the engine and
wait for five minutes.
2. Place the machine on a level place and
hold it up on upright position by placing
the suitable stand under the engine.
3. Remove:
lOil tank cap 1
4. Inspect:
lOil level
Oil level should be between maximum
a and minimum b marks.
Oil level is low ® Add oil to proper
level.
NOTE:
When inspecting the oil level, do not screw the
oil tank cap into the oil tank. Insert the gauge
lightly.
ENGINE OIL LEVEL INSPECTION

3 - 18
INSP
ADJ
OIL PRESSURE INSPECTION
1. Check:
lOil pressure
Checking steps:
lSlightly loosen the oil pressure check bolt
1.
lStart the engine and keep it idling until oil
starts to seep from the oil pressure check
bolt. If no oil comes out after one minute,
turn the engine off so it will not seize.
lCheck oil passages and oil pump for dam-
age or leakage.
lStart the engine after solving the prob-
lem(s) and recheck the oil pressure.
lTighten the oil pressure check bolt.
T R..
Oil pressure check bolt:
10 Nm (1.0 m • kg, 7.2 ft • lb)
PILOT SCREW ADJUSTMENT
1. Adjust:
lPilot screw 1
Adjustment steps:
NOTE:
To optimize the fuel flow at a smaller throttle
opening, each machine’s pilot screw has
been individually set at the factory. Before
adjusting the pilot screw, turn it in fully and
count the number of turns. Record this num-
ber as the factory-set number of turns out.
lTurn in the pilot screw until it is lightly
seated.
lTurn out the pilot screw by the factory-set
number of turns.
Pilot screw:
1-3/4 turns out (example)
OIL PRESSURE INSPECTION/
PILOT SCREW ADJUSTMENT