brake YAMAHA WR 250F 2001 Service Manual

5 - 13
CHAS
BRAKE CALIPER DISASSEMBLY
Front
õRear
Extent of removal:1 Front brake caliper disassembly2 Rear brake caliper disassembly
Extent of removal Order Part name Q’ty Remarks
BRAKE CALIPER DISASSEM-
BLYAB
1 Pad pin 1 1
2 Brake pad 2 2
3 Pad support 1 1
4 Brake caliper piston 2 1 Refer to “REMOVAL POINTS”.
5 Dust seal 2 1
Refer to “REMOVAL POINTS”.
6 Piston seal 2 1
12
FRONT BRAKE AND REAR BRAKE

5 - 14
CHASFRONT BRAKE AND REAR BRAKE
BRAKE MASTER CYLINDER DISASSEMBLY
Front
õRear
Extent of removal:1 Front brake master cylinder disassembly2 Rear brake master cylinder disassembly
Extent of removal Order Part name Q’ty Remarks
BRAKE MASTER CYLINDER
DISASSEMBLY
1 Brake master cylinder cap 1
2 Diaphragm 1
3 Brake master cylinder boot 1
4 Circlip 1 Use a long nose circlip pliers.
5 Washer 1
6 Push rod 1
7 Brake master cylinder kit
1
12
21

5 - 15
CHASFRONT BRAKE AND REAR BRAKE
EC5A3000
REMOVAL POINTS
Brake fluid
1. Remove:
[Front]
lBrake master cylinder cap 1
[Rear]
lBrake master cylinder guard 1
lReservoir tank cap 2
NOTE:
Do not remove the diaphragm.
Front
õRear
2. Connect the transparent hose 2 to the
bleed screw 1 and place a suitable con-
tainer under its end.
Front
õRear

õ
3. Loosen the bleed screw and drain the
brake fluid while pulling the lever in or
pushing down on the pedal.
CAUTION:
lDo not reuse the drained brake fluid.
lBrake fluid may erode painted surfaces or
plastic parts. Always clean up spilled
fluid immediately.
õ

Brake caliper piston
1. Remove:
lBrake caliper piston
Use compressed air and proceed care-
fully.
WARNING
lCover piston with rag and use extreme
caution when expelling piston from cylin-
der.
lNever attempt to pry out piston.
Front
õRear
Caliper piston removal steps:
lInsert a piece of rag into the brake caliper
to lock one brake caliper.
lCarefully force the piston out of the brake
caliper cylinder with compressed air.

õ

5 - 16
CHASFRONT BRAKE AND REAR BRAKE
Brake caliper piston seal kit
1. Remove:
lDust seal 1
lPiston seal 2
NOTE:
Remove the piston seals and dust seals by
pushing them with a finger.
CAUTION:
Never attempt to pry out piston seals and
dust seals.
WARNING
Replace the piston seals and dust seals
whenever a caliper is disassembled.
Front
õRear

õ
EC5A4000
INSPECTION
Brake master cylinder
1. Inspect:
lBrake master cylinder inner surface a
Wear/scratches ® Replace master cyl-
inder assembly.
Stains ® Clean.
WARNING
Use only new brake fluid.
Front
õRear
2. Inspect:
lDiaphragm 1
Crack/damage ® Replace.
Front
õRear
õ
õ

3. Inspect:
lBrake master cylinder piston 1
lBrake master cylinder cup 2
Wear/damage/score marks ® Replace
brake master cylinder kit.
Front
õRear
õ

5 - 17
CHAS
Brake caliper
1. Inspect:
lBrake caliper cylinder inner surface a
Wear/score marks ® Replace brake
caliper assembly.
Front
õRear
õ
2. Inspect:
lBrake caliper piston 1
Wear/score marks ® Replace brake
caliper piston assembly.
WARNING
Replace the piston seals and dust seals 2
whenever a caliper is disassembled.
EC534301
Brake hose
1. Inspect:
lBrake hose 1
Crack/damage ® Replace.
EC5A5000
ASSEMBLY AND INSTALLATION
WARNING
lAll internal parts should be cleaned in
new brake fluid only.
lInternal parts should be lubricated with
brake fluid when installed.
lReplace the piston seals and dust seals
whenever a caliper is disassembled.
Brake caliper piston
1. Clean:
lBrake caliper
lPiston seal
lDust seal
lBrake caliper piston
Clean them with brake fluid.
FRONT BRAKE AND REAR BRAKE

5 - 18
CHAS
2. Install:
lPiston seal 1
lDust seal 2
WARNING
Always use new piston seals and dust
seals.
NOTE:
Fit the piston seals and dust seals onto the slot
on brake caliper correctly.
Front
õRear

õ
3. Install:
lBrake caliper piston 1
NOTE:
Apply the brake fluid on the piston wall.
CAUTION:
lFor the front brake caliper, install the pis-
ton with its depressed side a facing the
brake caliper. For the rear brake caliper,
install the piston with its shallow
depressed side b facing the caliper.
lNever force to insert.
Front
õRear
Front brake caliper
1. Install:
lPad support 1
lBrake pad 2
lPad pin 3
NOTE:
lInstall the brake pads with their projections
a into the brake caliper recesses b.
lTemporarily tighten the pad pin at this point.

õ
FRONT BRAKE AND REAR BRAKE

5 - 19
CHASFRONT BRAKE AND REAR BRAKE
2. Install:
lCopper washer 1
lUnion bolt 2
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose so that its pipe por-
tion a directs as show and lightly touches
the projection b on the brake caliper.
T R..30 Nm (3.0 m · kg, 22 ft · lb)
3. Install:
lBrake hose holder 1
lBrake caliper 2
lBolt (brake caliper) 3
NOTE:
Fit the brake hose holder cut a over the pro-
jection b on the front fork and clamp the brake
hose.
4. Tighten:
lPad pin 4
5. Install:
lPad pin plug 5
Rear brake caliper
1. Install:
lPad support 1
lBrake pad 2
lPad pin 3
NOTE:
lInstall the brake pads with their projections
a into the brake caliper recesses b.
lTemporarily tighten the pad pin at this point.
T R..23 Nm (2.3 m · kg, 17 ft · lb)
T R..18 Nm (1.8 m · kg, 13 ft · lb)
T R..3 Nm (0.3 m · kg, 2.2 ft · lb)

5 - 20
CHASFRONT BRAKE AND REAR BRAKE
2. Install:
lBrake disc cover 1
lBolt (brake disc cover) 2
T R..7 Nm (0.7 m · kg, 5.1 ft · lb)
3. Install:
lCopper washer 1
lBrake hose 2
lUnion bolt 3
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose to the brake caliper
with the paint a on the pipe facing the
brake caliper and with the pipe contacting
the brake caliper projection b.
T R..30 Nm (3.0 m · kg, 22 ft · lb)
4. Install:
lBrake caliper 1
lRear wheel 2
Refer to “FRONT WHEEL AND REAR
WHEEL” section.
5. Tighten:
lPad pin 3
6. Install:
lPad pin plug 4
T R..18 Nm (1.8 m · kg, 13 ft · lb)
T R..3 Nm (0.3 m · kg, 2.2 ft · lb)

5 - 21
CHASFRONT BRAKE AND REAR BRAKE
Brake master cylinder kit
1. Clean:
lBrake master cylinder
lBrake master cylinder kit
Clean them with brake fluid.
2. Install:
lBrake master cylinder cup (primary) 1
lBrake master cylinder cup (secondary)
2
To brake master cylinder piston 3.
NOTE:
Apply the brake fluid on the brake master cyl-
inder cup.
WARNING
After installing, cylinder cup should be
installed as shown direction. Wrong instal-
lation cause improper brake performance.
Front
õRear
õ

3. Install:
lSpring 1
To brake master cylinder piston 2.
NOTE:
Install the spring at the smaller dia. side.
Front
õRear

5 - 22
CHASFRONT BRAKE AND REAR BRAKE
4. Install:
[Front]
lBrake master cylinder kit 1
lWasher 2
lCirclip 3
lBrake master cylinder boot 4
To brake master cylinder 5.
[Rear]
lBrake master cylinder kit 1
lPush rod 2
lCirclip 3
lBrake master cylinder boot 4
To brake master cylinder 5.
NOTE:
lApply the brake fluid on the brake master
cylinder kit.
lApply the lithium soap base grease on the tip
of the push rod.
lWhen installing the circlip, use a long nose
circlip pliers.
Front
õRear

õ
Front brake master cylinder
1. Install:
lBrake master cylinder 1
lBrake master cylinder bracket 2
lBolt (brake master cylinder bracket) 3
NOTE:
lInstall the bracket so that the arrow mark a
face upward.
lFirst tighten the bolts on the upper side of the
brake master cylinder bracket, and then
tighten the bolts on the lower side.
T R..9 Nm (0.9 m · kg, 6.5 ft · lb)