ad blue YAMAHA WR 400F 2002 Betriebsanleitungen (in German)

4 - 25
ENGCAMSHAFTS
6. Remove:
Clips
Exhaust camshaft 1
Intake camshaft 2
NOTE:
Attach a wire 3 to the timing chain to prevent
it from falling into the crankcase.
INSPECTION
Camshaft
1. Inspect:
Cam lobes
Pitting/scratches/blue discoloration →
Replace.
2. Measure:
Cam lobes length a and b
Out of specification → Replace.
Cam lobes length:
Intake:
a31.7 ~ 31.8 mm
(1.2480 ~ 1.2520 in)
: 31.6 mm (1.244 in)
b22.95 ~ 23.05 mm
(0.9035 ~ 0.9075 in)
: 22.85 mm (0.900 in)
Exhaust:
a31.2 ~ 31.3 mm
(1.2283 ~ 1.2323 in)
: 31.1 mm (1.224 in)
b22.95 ~ 23.05 mm
(0.9035 ~ 0.9075 in)
: 22.85 mm (0.900 in)
3. Measure:
Runout (camshaft)
Out of specification → Replace.
Runout (camshaft):
Less than 0.03 mm (0.0012 in)

4 - 37
ENGVALVES AND VALVE SPRINGS
5. Measure:
Runout (valve stem)
Out of specification → Replace.
NOTE:
When installing a new valve always replace
the guide.
If the valve is removed or replaced always
replace the oil seal.
6. Eliminate:
Carbon deposits
(from the valve face and valve seat)
7. Inspect:
Valve seats
Pitting/wear → Reface the valve seat.
Runout limit:
0.01 mm (0.0004 in)
8. Measure:
Valve seat width a
Out of specification → Reface the valve
seat.
Valve seat width:
Intake:
0.9 ~ 1.1 mm (0.0354 ~ 0.0433 in)
: 1.6 mm (0.0630 in)
Exhaust:
0.9 ~ 1.1 mm (0.0354 ~ 0.0433 in)
: 1.6 mm (0.0630 in)
Measurement steps:
Apply Mechanic’s blueing dye (Dykem) b
to the valve face.
Install the valve into the cylinder head.
Press the valve through the valve guide
and onto the valve seat to make a clear
pattern.
Measure the valve seat width. Where the
valve seat and valve face made contact,
blueing will have been removed.
If the valve seat is too wide, too narrow, or
the seat is not centered, the valve seat
must be refaced.

4 - 38
ENGVALVES AND VALVE SPRINGS
9. Lap:
Valve face
Valve seat
NOTE:
After refacing the valve seat or replacing the
valve and valve guide, the valve seat and
valve face should be lapped.
Lapping steps:
Apply a coarse lapping compound to the
valve face.
CAUTION:
Do not let the compound enter the gap
between the valve stem and the guide.
Apply molybdenum disulfide oil to the
valve stem.
Install the valve into the cylinder head.
Turn the valve until the valve face and
valve seat are evenly polished, then clean
off all of the compound.
NOTE:
For best lapping results, lightly tap the valve
seat while rotating the valve back and forth
between your hands.
Apply a fine lapping compound to the
valve face and repeat the above steps.
NOTE:
After every lapping operation be sure to
clean off all of the compound from the valve
face and valve seat.
Apply Mechanic’s blueing dye (Dykem) to
the valve face.
Install the valve into the cylinder head.
Press the valve through the valve guide
and onto the valve seat to make a clear
pattern.
Measure the valve seat width again. If the
valve seat width is out of specification,
reface and relap the valve seat.

4 - 40
ENG

VALVES AND VALVE SPRINGS
Combination of cylinder head and valve
lifter
1. Combination:
For this combination, match the paint
color on the cylinder head with that on
the valve lifter according to the chart
below.
NOTE:

When you purchase a cylinder head, you can-
not designate its size. Choose the valve lifter
that matches the above chart.
Combination
Cylinder head mark
a
(color)Valve lifter mark
b
(color)
Blue Blue
Yellow Yellow
Purple Black
ASSEMBLY AND INSTALLATION
1. Apply:

Molybdenum disulfide oil
Onto the valve stem and valve stem
seal.
2. Install:

Valves
1


Valve spring seats
2


Valve stem seals
3


Valve springs
4


Valve spring retainers
5

NOTE:


Make sure that each valve is installed in its
original place, also referring to the painted
color as follows.
Intake (middle)
a
: light blue
Intake (right/left)
b
: white
Exhaust: not paint

Install the valve springs with the larger pitch
c
facing upward.
d
Smaller pitch
New

4 - 46
ENGCYLINDER AND PISTON
3. Measure:
Ring end gap
Out of specification → Replace.
NOTE:
You cannot measure the end gap on the
expander spacer of the oil control ring. If the oil
control ring rails show excessive gap, replace
all three rings.
End gap
Standard Limit
Top
ringWR426F:
0.20 ~ 0.30 mm
(0.008 ~ 0.012 in)
WR400F:
0.20 ~ 0.35 mm
(0.008 ~ 0.014 in)WR426F:
0.55 mm
(0.022 in)
WR400F:
0.60 mm
(0.024 in)
2nd
ringWR426F:
0.35 ~ 0.50 mm
(0.014 ~ 0.020 in)
WR400F:
0.40 ~ 0.55 mm
(0.016 ~ 0.022 in)WR426F:
0.85 mm
(0.033 in)
WR400F:
0.90 mm
(0.035 in)
Oil
ring0.20 ~ 0.50 mm
(0.01 ~ 0.02 in)—
Piston pin
1. Inspect:
Piston pin
Blue discoloration/grooves →
Replace, then inspect the lubrication
system.

6 - 1
–+ELECELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC600000
ELECTRICAL
EC610000
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC611000
ELECTRICAL COMPONENTS
1Headlight
2“ENGINE STOP” button
3Regulator
4TPS (throttle position sensor)
5Tail light
6CDI magneto
7Neutral switch
8Ignition coil
9Spark plug
0Lights switch
ACDI unitCOLOR CODE
B ................... Black
Br .................. Brown
G ................... Green
Gy ................. Gray
L .................... Blue
O ................... Orange
P ................... Pink
R ................... Red
Sb ................. Sky blue
EC612000
WIRING DIAGRAM
* Except for USA
B/L
R/WL/W
LY
L
Y
B
1B L
L
B YL
B YYYLB
5LB
YBLB
LB
3
7
4 8
9
W
R Br
G PB/YP
B Br
G W
R
O
L Y B/LL/WSb
B/L Y O
L
A
Y
Br
Gy
PGR
WB
L YL Y
B B/L
SbW
Sb
WL/W
R/WL/WL/WR/WSb
W
O
B
0
6
B GyBGy
O
L Y Sb
B/L*
B*
Sb*
Y
BL
B
B
B
B/WBB/W G/B
2
W................... White
Y.................... Yellow
B/L................. Black/Blue
B/W ............... Black/White
B/Y ................ Black/Yellow
G/B ................ Green/Black
L/W................ Blue/White
R/W ............... Red/White

6 - 6
–+ELECIGNITION SYSTEM
2. Inspect:
Source coil 1 resistance
Out of specification → Replace.
3. Inspect:
Source coil 2 resistance
Out of specification → Replace. Tester (+) lead → Brown lead 1
Tester (–) lead → Green lead 2
Source coil 1
resistanceTester selector
position
640 ~ 960 Ω at
20 ˚C (68 ˚F)Ω × 100
Tester (+) lead → Pink lead 1
Tester (–) lead → Green lead 2
Source coil 2
resistanceTester selector
position
464 ~ 696 Ω at
20 ˚C (68 ˚F)Ω × 10
NEUTRAL SWITCH INSPECTION
1. Inspect:
Neutral switch conduct
* Except for USA
No continuity while in neutral → Replace.
Continuity while in gear → Replace.
ÅFor USA
ıExcept for USA
EC628000
CDI UNIT INSPECTION
Check all electrical components. If no fault is
found, replace the CDI unit. Then check the
electrical components again.Tester (+) lead → Blue/White lead 1
*Sky blue lead 1
Tester (–) lead → Ground
L/W
*Sb 1GroundTester selec-
tor position
NEU-
TRAL
Ω × 1
IN GEAR
–+ Ω×1
R/W
W Sb L/W
1
Å
–+ Ω×1
R/W
W Sb L/W
1
ı

6 - 8
–+ELECTPS (THROTTLE POSITION SENSOR) SYSTEM
HANDLING NOTE
CAUTION:
Do not loosen the screw {TPS (throttle
position sensor)} 1 except when changing
the TPS (throttle position sensor) due to
failure because it will cause a drop in
engine performance.
EC624000
COUPLERS AND LEADS CONNECTION
INSPECTION
1. Check:
Couplers and leads connection
Rust/dust/looseness/short-circuit →
Repair or replace.
TPS COIL INSPECTION
1. Inspect:
TPS coil resistance
Out of specification → Replace.
2. Loosen:
Throttle stop screw 1
NOTE:
Turn out the throttle stop screw until the throt-
tle shaft is in the full close position.Tester (+) lead → Blue lead 1
Tester (–) lead → Black lead 2
TPS coil
resistanceTester selector
position
4 ~ 6 kΩ at
20 ˚C (68 ˚F)kΩ × 1

6 - 11
–+ELEC
8. Tighten:
Screw (TPS) 1
9. Stop the engine.
EC694000
TPS INPUT VOLTAGE INSPECTION
1. Disconnect the TPS coupler.
2. Start the engine.
3. Inspect:
TPS input voltage
Out of specification → Replace the CDI
unit.
Tester (+) lead → Blue lead 1
Tester (–) lead → Black/Blue lead 2
TPS input
voltageTester selector
position
4 ~ 6 V DCV-20
TPS (THROTTLE POSITION SENSOR) SYSTEM

6 - 13
–+ELECLIGHTING SYSTEM
LIGHTS SWITCH INSPECTION
1. Inspect:
Lights switch conduct
No continuity while being → Replace.
Continuity while being OFF → Replace. Tester (+) lead → Yellow lead 1
Tester (–) lead → Blue lead 2
Y
1L
2Tester selec-
tor position
Ω × 1
OFF
CDI MAGNETO INSPECTION
1. Inspect:
Lighting coil resistance
Out of specification → Replace.
REGULATOR INSPECTION
1. Start the engine.
2. Turn on the headlight and tail light by
turning on the lights switch.
3. Inspect:
Out-put voltage
Out of specification → Replace regula-
tor. Tester (+) lead → Yellow lead 1
Tester (–) lead → Black lead 2
Lighting coil
resistanceTester selector
position
0.16 ~ 0.24 Ω at
20 ˚C (68 ˚F)Ω × 1
Tester (+) lead → Blue lead 1
Tester (–) lead → Black lead 2
Out-put voltageTester selector
position
13.3 ~ 14.3 V at
5,000 r/minACV-20
BL
1
2
1
2