length YAMAHA WR 400F 2002 Betriebsanleitungen (in German)
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2002, Model line: WR 400F, Model: YAMAHA WR 400F 2002Pages: 776, PDF-Größe: 41.64 MB
Page 8 of 776
5. GASOLINE IS HIGHLY FLAMMABLE.
Always turn off the engine while refu-
eling. Take care to not spill any gaso-
line on the engine or exhaust system.
Never refuel in the vicinity of an open
flame, or while smoking.
6. GASOLINE CAN CAUSE INJURY.
If you should swallow some gasoline,
inhale excess gasoline vapors, or
allow any gasoline to get into your
eyes, contact a doctor immediately. If
any gasoline spills onto your skin or
clothing, immediately wash skin areas
with soap and water, and change your
clothes.
7. ONLY OPERATE THE MACHINE IN AN
AREA WITH ADEQUATE VENTILA-
TION.
Never start the engine or let it run for
any length of time in an enclosed area.
Exhaust fumes are poisonous. These
fumes contain carbon monoxide,
which by itself is odorless and color-
less. Carbon monoxide is a dangerous
gas which can cause unconscious-
ness or can be lethal.
8. PARK THE MACHINE CAREFULLY;
TURN OFF THE ENGINE.
Always turn off the engine if you are
going to leave the machine. Do not
park the machine on a slope or soft
ground as it may fall over.
9. THE ENGINE, EXHAUST PIPE, MUF-
FLER, AND OIL TANK WILL BE VERY
HOT AFTER THE ENGINE HAS BEEN
RUN.
Be careful not to touch them or to
allow any clothing item to contact
them during inspection or repair.
10. PROPERLY SECURE THE MACHINE
BEFORE TRANSPORTING IT.
When transporting the machine in
another vehicle, always be sure it is
properly secured and in an upright
position and that the fuel cock is in
the “OFF” position. Otherwise, fuel
may leak out of the carburetor or fuel
tank.
Page 76 of 776
2 - 1
SPECGENERAL SPECIFICATIONS (WR426F)
EC200000
SPECIFICATIONS
EC211000
GENERAL SPECIFICATIONS (WR426F)
Model name: WR426FP (USA)
WR426F (EUROPE)
WR426F(P) (CDN, AUS, NZ, ZA)
Model code number: 5NG5 (USA)
5NG6 (EUROPE)
5NG8 (CDN, AUS, NZ, ZA)
Dimensions:
Overall length 2,171 mm (85.5 in)
Overall width 827 mm (32.6 in)
Overall height 1,303 mm (51.3 in)
Seat height 998 mm (39.3 in)
Wheelbase 1,490 mm (58.7 in)
Minimum ground clearance 373 mm (14.7 in)
Basic weight:
With oil and full fuel tank 121.5 kg (268 lb)
Engine:
Engine type Liquid cooled 4-stroke, DOHC
Cylinder arrangement Single cylinder, forward inclined
Displacement 426 cm
3 (15.0 Imp oz, 14.4 US oz)
Bore × stroke 95.0 × 60.1 mm (3.74 × 2.37 in)
Compression ratio 12.5 : 1
Starting system Kick starter
Lubrication system: Dry sump
Oil type or grade:
Engine oil
(For USA and CDN)
At 5 ˚C (40 ˚F) or higher Å
Yamalube 4 (20W-40) or SAE 20W-40 type SH
motor oil (Non-Friction modified)
At 15 ˚C (60 ˚F) or lower ı
Yamalube 4 (10W-30) or SAE 10W-30 type SH
motor oil (Non-Friction modified) and/or
Yamalube 4-R (15W-50) (Non-Friction modified)
(Except for USA and CDN)
API “SH” or higher grade
-20
-4-10
140
3010
5020
6830
8640 50
104
122°CTemp.
°F
10W-30
10W-40
20W-40
20W-50
15W-40
Page 81 of 776
2 - 6
SPECMAINTENANCE SPECIFICATIONS (WR426F)
Valve seat width IN 0.9 ~ 1.1 mm
(0.0354 ~ 0.0433 in)1.6 mm
(0.0630 in)
EX 0.9 ~ 1.1 mm
(0.0354 ~ 0.0433 in)1.6 mm
(0.0630 in)
Valve spring:
Free length IN 41.36 mm (1.63 in) 39.3 mm
(1.55 in)
EX 43.60 mm (1.72 in) 41.4 mm
(1.63 in)
Set length (valve closed) IN 32.87 mm (1.29 in) ----
EX 35.38 mm (1.39 in) ----
Compressed pressure
(installed) IN 112.8 ~ 129.8 N
(11.5 ~ 13.2 kg, 25.35 ~ 29.10 lb)----
EX 116.3 ~ 133.9 N
(11.9 ~ 13.7 kg, 26.23 ~ 30.20 lb)----
Tilt limit IN ---- 2.5˚/1.8 mm
(2.5˚/0.071 in)
EX ---- 2.5˚/1.9 mm
(2.5˚/0.075 in)
Direction of winding
(top view) IN Clockwise ----
EX Clockwise ----
Piston:
Piston to cylinder clearance 0.040 ~ 0.065 mm
(0.0016 ~ 0.0026 in)0.1 mm
(0.004 in)
Piston size “D”94.945 ~ 94.960 mm
(3.738 ~ 3.739 in)----
Measuring point “H”9 mm (0.354 in) ----
Piston off-set 1 mm (0.0394 in) ----
Piston pin bore inside diameter 19.004 ~ 19.015 mm
(0.7482 ~ 0.7486 in)19.045 mm
(0.7498 in)
Piston pin outside diameter 18.991 ~ 19.000 mm
(0.7477 ~ 0.7480 in)18.971 mm
(0.7469 in) Item Standard Limit
*
H
D
Page 83 of 776
2 - 8
SPECMAINTENANCE SPECIFICATIONS (WR426F)
Clutch:
Friction plate thickness 2.9 ~ 3.1 mm (0.114 ~ 0.122 in) 2.7 mm
(0.106 in)
Quantity 9 ----
Clutch plate thickness 1.1 ~ 1.3 mm (0.043 ~ 0.051 in) ----
Quantity 8 ----
Warp limit ---- 0.1 mm
(0.004 in)
Clutch spring free length 48.4 mm (1.91 in) 47.4 mm
(1.87 in)
Quantity 6 ----
Clutch housing thrust clearance 0.10 ~ 0.35 mm
(0.0039 ~ 0.0138 in)----
Clutch housing radial clearance 0.010 ~ 0.044 mm
(0.0004 ~ 0.0017 in)----
Clutch release method Inner push, cam push ----
Shifter:
Shifter type Cam drum and guide bar ----
Guide bar bending limit ---- 0.05 mm
(0.002 in)
Kick starter:
Type Ratchet type ----
Carburetor:
USAEUROPE,
CDN, AUS, NZ,
ZA
I. D. mark 5NG5 50 5NG6 60 ----
Main jet (M.J) #165←----
Main air jet (M.A.J) #200←----
Jet needle-clip position (J.N) OBDRR-4 OBDQR-4 ----
Cutaway (C.A) 1.5←----
Pilot jet (P.J) #42←----
Pilot air jet (P.A.J) #75←----
Pilot outlet (P.O)ø0.9←----
Pilot screw (example) (P.S) 1-5/8 1-1/8 ----
Bypass (B.P)ø1.0←----
Valve seat size (V.S)ø3.8←----
Starter jet (G.S) #65←----
Float height (F.H) 8 mm (0.31 in)←----
Engine idle speed 1,700 ~
1,900 r/min←----
Intake vacuum 33.3 ~ 38.7 kPa
(250 ~ 290 mmHg,
9.84 ~ 11.42 inHg)←---- Item Standard Limit
Page 88 of 776
2 - 13
SPECMAINTENANCE SPECIFICATIONS (WR426F)
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing ----
Front suspension: USA, CDN
AUS, NZ, ZAEUROPE
Front fork travel 300 mm
(11.8 in)←----
Fork spring free length 460 mm
(18.1 in)←455 mm (17.9 in)
Spring rate, STD K = 4.51 N/mm
(0.46 kg/mm,
25.8 lb/in)K = 4.12 N/mm
(0.42 kg/mm,
23.5 lb/in)----
Optional spring/spacer Yes←----
Oil capacity 568 cm
3
(20.0 lmp oz,
19.2 US oz) 578 cm3
(20.3 lmp oz,
19.5 US oz)----
Oil level 135 mm
(5.31 in)125 mm
(4.92 in)----
(From top of outer tube with inner
tube and damper rod fully com-
pressed without spring.)80 ~ 150 mm
(3.15 ~ 5.91 in)←----
Oil grade Suspension oil
“01”←----
Inner tube outer diameter 46 mm (1.81 in)←----
Front fork top end Zero mm
(Zero in)←----
Rear suspension: USA, CDN,
AUS, NZ, ZAEUROPE
Shock absorber travel 132 mm
(5.20 in)←----
Spring free length 260 mm
(10.24 in)←----
Fitting length 246 mm
(9.69 in)247 mm
(9.72 in)----
(9.47 ~ 10.18 in)←----
Spring rate, STD K = 51.0 N/mm
(5.20 kg/mm,
291.2 lb/in)K = 49.0 N/mm
(5.00 kg/mm,
280.0 lb/in)----
Optional spring Yes←----
Enclosed gas pressure 1,000 kPa
(10 kg/cm
2,
142 psi)←----
Swingarm:
Swingarm free play limit
End ---- 1.0 mm (0.04 in)
Page 89 of 776
2 - 14
SPECMAINTENANCE SPECIFICATIONS (WR426F)
Wheel:
Front wheel type Spoke wheel ----
Rear wheel type Spoke wheel ----
Front rim size/material 21 × 1.60/Aluminum ----
Rear rim size/material 18 × 2.15/Aluminum ----
Rim runout limit
Radial ---- 2.0 mm (0.08 in)
Lateral ---- 2.0 mm (0.08 in)
Drive chain:
Type/manufacturer DID520VM/DAIDO ----
Number of links 113 links + joint ----
Chain slack 40 ~ 50 mm (1.6 ~ 2.0 in) ----
Chain length (10 links) ----150.1 mm (5.91 in)
Front disc brake:
Disc outside diameter × Thickness 250 × 3.0 mm (9.84 × 0.12 in) 250 × 2.5 mm
(9.84 × 0.10 in)
Pad thickness 4.4 mm (0.17 in) 1.0 mm (0.04 in)
Master cylinder inside dia. 11.0 mm (0.433 in) ----
Caliper cylinder inside dia. 27.0 mm (1.063 in) × 2 ----
Brake fluid type DOT #4 ----
Rear disc brake:
Disc outside diameter × Thickness 245 × 4.0 mm (9.65 × 0.16 in) 245 × 3.5 mm
(9.65 × 0.14 in)
Deflection limit ----0.15 mm (0.006 in)
Pad thickness 6.4 mm (0.25 in) 1.0 mm (0.04 in)
Master cylinder inside dia. 12.7 mm (0.500 in) ----
Caliper cylinder inside dia. 27.0 mm (1.063 in) × 1 ----
Brake fluid type DOT #4 ----
Brake lever and brake pedal:
Brake lever position 95 mm (3.74 in) ----
Brake pedal height
(vertical height below footrest top)5 mm (0.20 in) ----
Clutch lever free play (lever end) 8 ~ 13 mm (0.31 ~ 0.51 in) ----
Throttle grip free play 3 ~ 5 mm (0.12 ~ 0.20 in) ----Item Standard Limit
Page 93 of 776
2 - 18
SPECGENERAL SPECIFICATIONS (WR400F)
EC211000
GENERAL SPECIFICATIONS (WR400F)
Model name: WR400F (EUROPE)
WR400FP (AUS)
Model code number: 5GSA
Dimensions:
Overall length 2,171 mm (85.5 in)
Overall width 827 mm (32.6 in)
Overall height 1,303 mm (51.3 in)
Seat height 998 mm (39.3 in)
Wheelbase 1,490 mm (58.7 in)
Minimum ground clearance 373 mm (14.7 in)
Basic weight:
With oil and full fuel tank 121.5 kg (268 lb)
Engine:
Engine type Liquid cooled 4-stroke, DOHC
Cylinder arrangement Single cylinder, forward inclined
Displacement 399 cm
3 (14.1 Imp oz, 13.5 US oz)
Bore × stroke 92.0 × 60.1 mm (3.62 × 2.37 in)
Compression ratio 12.5 : 1
Starting system Kick starter
Lubrication system: Dry sump
Oil type or grade:
Engine oil
API “SH” or higher grade
Oil capacity:
Engine oil
Periodic oil change 1.3 L (1.14 Imp qt, 1.37 US qt)
With oil filter replacement 1.4 L (1.23 Imp qt, 1.48 US qt)
Total amount 1.5 L (1.32 Imp qt, 1.59 US qt)
Coolant capacity (including all routes): 1.2 L (1.06 Imp qt, 1.27 US qt)
Air filter: Wet type element
-20
-4-10
140
3010
5020
6830
8640 50
104
122°CTemp.
°F
10W-30
10W-40
20W-40
20W-50
15W-40
Page 98 of 776
2 - 23
SPECMAINTENANCE SPECIFICATIONS (WR400F)
Valve seat width IN0.9 ~ 1.1 mm
(0.0354 ~ 0.0433 in)1.6 mm
(0.0630 in)
EX 0.9 ~ 1.1 mm
(0.0354 ~ 0.0433 in)1.6 mm
(0.0630 in)
Valve spring:
Free length IN 41.36 mm (1.63 in) 39.3 mm
(1.55 in)
EX 43.60 mm (1.72 in) 41.4 mm
(1.63 in)
Set length (valve closed) IN 32.86 mm (1.29 in) ----
EX 35.38 mm (1.39 in) ----
Compressed pressure
(installed) IN 112.8 ~ 129.8 N
(11.5 ~ 13.2 kg, 25.35 ~ 29.10 lb)----
EX 116.3 ~ 133.9 N
(11.9 ~ 13.7 kg, 26.23 ~ 30.20 lb)----
Tilt limit IN ---- 2.5˚/1.8 mm
(2.5˚/0.071 in)
EX ---- 2.5˚/1.9 mm
(2.5˚/0.075 in)
Direction of winding
(top view) IN Clockwise ----
EX Clockwise ----
Piston:
Piston to cylinder clearance 0.040 ~ 0.065 mm
(0.0016 ~ 0.0026 in)0.1 mm
(0.004 in)
Piston size “D”91.945 ~ 91.960 mm
(3.6199 ~ 3.6205 in)----
Measuring point “H”9 mm (0.354 in) ----
Piston off-set 1 mm (0.0394 in) ----
Piston pin bore inside diameter 18.004 ~ 18.015 mm
(0.7088 ~ 0.7093 in)18.045 mm
(0.7104 in)
Piston pin outside diameter 17.991 ~ 18.000 mm
(0.7083 ~ 0.7087 in)17.971 mm
(0.7075 in) Item Standard Limit
*
H
D
Page 100 of 776
2 - 25
SPECMAINTENANCE SPECIFICATIONS (WR400F)
Clutch:
Friction plate 1 thickness 2.72 ~ 2.88 mm
(0.107 ~ 0.113 in)2.52 mm
(0.099 in)
Inner diameterø112 mm (4.41 in) ----
Quantity 7 ----
Friction plate 2 thickness 2.92 ~ 3.08 mm
(0.115 ~ 0.121 in)2.72 mm
(0.107 in)
Inner diameterø116 mm (4.57 in) ----
Quantity 1 ----
Clutch plate thickness 1.1 ~ 1.3 mm (0.043 ~ 0.051 in) ----
Quantity 7 ----
Warp limit ---- 0.1 mm
(0.004 in)
Clutch spring free length 44 mm (1.73 in) 43 mm
(1.69 in)
Quantity 5 ----
Clutch housing thrust clearance 0.20 ~ 0.45 mm
(0.0079 ~ 0.0177 in)----
Clutch housing radial clearance 0.010 ~ 0.044 mm
(0.0004 ~ 0.0017 in)----
Clutch release method Inner push, cam push ----
Shifter:
Shifter type Cam drum and guide bar ----
Guide bar bending limit ---- 0.05 mm
(0.002 in)
Kick starter:
Type Ratchet type ----
Carburetor:
I. D. mark 5GS6 61 ----
Main jet (M.J) #165 ----
Main air jet (M.A.J) #200 ----
Jet needle-clip position (J.N) OBDRQ-4 ----
Cutaway (C.A) 1.5 ----
Pilot jet (P.J) #42 ----
Pilot air jet (P.A.J) #75 ----
Pilot outlet (P.O)ø0.9 ----
Pilot screw (example) (P.S) 1-1/2 ----
Bypass (B.P)ø1.0 ----
Valve seat size (V.S)ø3.8 ----
Starter jet (G.S) #65 ----
Float height (F.H) 8 mm (0.31 in) ----
Engine idle speed 1,700 ~ 1,900 r/min ----
Intake vacuum 33.3 ~ 38.7 kPa
(250 ~ 290 mmHg, 9.84 ~ 11.42 inHg)---- Item Standard Limit
Page 105 of 776
2 - 30
SPECMAINTENANCE SPECIFICATIONS (WR400F)
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing ----
Front suspension: AUS EUROPE
Front fork travel 300 mm
(11.8 in)←----
Fork spring free length 460 mm
(18.1 in)←455 mm (17.9 in)
Spring rate, STD K = 4.51 N/mm
(0.46 kg/mm,
25.8 lb/in)K = 4.12 N/mm
(0.42 kg/mm,
23.5 lb/in)----
Optional spring/spacer Yes←----
Oil capacity 568 cm
3
(20.0 lmp oz,
19.2 US oz) 578 cm3
(20.3 lmp oz,
19.5 US oz)----
Oil level 135 mm
(5.31 in)125 mm
(4.92 in)----
(From top of outer tube with inner
tube and damper rod fully com-
pressed without spring.)80 ~ 150 mm
(3.15 ~ 5.91 in)←----
Oil grade Suspension oil
“01”←----
Inner tube outer diameter 46 mm (1.81 in)←----
Front fork top end Zero mm
(Zero in)←----
Rear suspension: AUS EUROPE
Shock absorber travel 132 mm
(5.20 in)←----
Spring free length 260 mm
(10.24 in)←----
Fitting length 246 mm
(9.69 in)247 mm
(9.72 in)----
(9.47 ~ 10.18 in)←----
Spring rate, STD K = 51.0 N/mm
(5.20 kg/mm,
291.2 lb/in)K = 49.0 N/mm
(5.00 kg/mm,
280.0 lb/in)----
Optional spring Yes←----
Enclosed gas pressure 1,000 kPa
(10 kg/cm
2,
142 psi)←----
Swingarm:
Swingarm free play limit
End ---- 1.0 mm (0.04 in)