coolant YAMAHA WR 400F 2002 Notices Demploi (in French)

1 - 1
GEN
INFO

DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1
Clutch lever
2
Decompression lever
3
“ENGINE STOP” button
4
Trip meter
5
Lights switch
6
Front brake lever
7
Throttle grip
8
Radiator cap
9
Fuel tank cap
0
Oil filler plug/dipstick
A
Tail light
B
Kick starter
C
Fuel tank
D
Headlight
E
Radiator
F
Coolant drain bolt
G
Rear brake pedal
H
Valve joint
I
Fuel cock
J
Cold starter knob
K
Hot starter knob (red)
L
Air cleaner
M
Drive chain
N
Shift pedal
O
Front fork
NOTE:


The machine you have purchased may differ
slightly from those shown in the following.

Designs and specifications are subject to
change without notice.
1

1 - 15
GEN
INFO
STARTING AND BREAK-IN
STARTING AND BREAK-IN
WARNING
Never start or run the engine in a closed
area. The exhaust fumes are poisonous;
they can cause loss of consciousness and
death in a very short time. Always operate
the machine in a well-ventilated area.
CAUTION:
The carburetor on this motorcycle has a
built-in accelerator pump. Therefore,
when starting the engine, do not operate
the throttle or the spark plug will foul.
Unlike a two-stroke engine, this engine
cannot be kick started when the throttle is
open because the kick starter may kick
back. Also, if the throttle is open the air/
fuel mixture may be too lean for the
engine to start.
Never use the decompression lever after
the engine is started. The engine may be
damaged if you use the decompression
lever while it is running.
Before starting the machine, perform the
checks in the pre-operation check list.
STARTING A COLD ENGINE
1. Inspect the coolant level.
2. Turn the fuel cock to “ON”.
3. Shift the transmission into neutral.
4. Fully open the cold starter knob.
5. Without pulling in the decompression
lever, slowly depress the kick starter until
the compression stroke is found. When
considerable resistance of the kick starter
is felt, the engine is on the compression
stroke. If the engine is on the exhaust
stroke, resistance will only be felt when
the kick starter is initially depressed, not
through the entire range of depression
(as when the engine is on the compres-
sion stroke); therefore, depress the kick
starter a few more times.

2 - 2
SPECGENERAL SPECIFICATIONS (WR426F)
Oil capacity:
Engine oil
Periodic oil change 1.3 L (1.14 Imp qt, 1.37 US qt)
With oil filter replacement 1.4 L (1.23 Imp qt, 1.48 US qt)
Total amount 1.5 L (1.32 Imp qt, 1.59 US qt)
Coolant capacity (including all routes): 1.2 L (1.06 Imp qt, 1.27 US qt)
Air filter: Wet type element
Fuel:
Type Premium unleaded gasoline only with a
research octane number of 95 or higher.
(Except for ZA)
Premium gasoline (For ZA)
Tank capacity 12 L (2.64 Imp gal, 3.17 US gal)
(For USA, CDN, AUS and NZ)
8.0 L (1.76 Imp gal, 2.11 US gal)
(For EUROPE and ZA)
Reserve 1.6 L (0.35 Imp gal, 0.42 US gal)
(For USA, CDN, AUS and NZ)
1.4 L (0.31 Imp gal, 0.37 US gal)
(For EUROPE and ZA)
Carburetor:
Type FCR-MX39
Manufacturer KEIHIN
Spark plug:
Type/manufacturer CR8E/NGK
U24ESR-N/DENSO
Gap 0.7 ~ 0.8 mm (0.028 ~ 0.031 in)
Clutch type: Wet, multiple-disc
Transmission:
Primary reduction system Gear
Primary reduction ratio 62/21 (2.952)
Secondary reduction system Chain drive
Secondary reduction ratio 50/14 (3.571)
Transmission type Constant mesh, 5-speed
Operation Left foot operation
Gear ratio: 1st 29/12 (2.416)
2nd 26/15 (1.733)
3rd 21/16 (1.312)
4th 21/20 (1.050)
5th 21/25 (0.840)
Chassis:
Frame type Semi double cradle
Caster angle 27.8˚
Trail 123 mm (4.84 in)

2

2 - 11
SPECMAINTENANCE SPECIFICATIONS (WR426F)
Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Spark plug M10S × 1.0 1 13 1.3 9.4
Camshaft cap M6 × 1.0 10 10 1.0 7.2
Cylinder head (stud bolt) M6 × 1.0 2 7 0.7 5.1
M8 × 1.25 3 15 1.5 11
(bolt) M10 × 1.25 4 44 4.4 32
(nut) M6 × 1.0 2 10 1.0 7.2
M8 × 1.25 2 20 2.0 14
Cylinder head cover M6 × 1.0 2 10 1.0 7.2
Cylinder M6 × 1.0 1 10 1.0 7.2
Timing chain tensioner M6 × 1.0 2 10 1.0 7.2
Tensioner cap bolt M6 × 1.0 1 7 0.7 5.1
Timing chain guide (rear) M6 × 1.0 2 10 1.0 7.2
Decompression shaft M6 × 1.0 1 7 0.7 5.1
Decompression cable guide M6 × 1.0 1 10 1.0 7.2
Exhaust pipe (nut) M8 × 1.25 1 13 1.3 9.4
(bolt) M8 × 1.25 1 24 2.4 17
Silencer M8 × 1.25 2 35 3.5 25
Silencer clamp M8 × 1.25 1 20 2.0 14
Exhaust pipe protector M6 × 1.0 3 10 1.0 7.2
Spark arrester (for USA) M6 × 1.0 3 10 1.0 7.2
Silencer end pipe (for USA) M6 × 1.0 1 10 1.0 7.2
Clamp (air cleaner joint) M5 × 0.8 1 3 0.3 2.2
Clamp (carburetor joint) M4 × 0.7 1 3 0.3 2.2
Air filter joint clamp M6 × 1.0 1 3 0.3 2.2
Throttle cable cover M5 × 0.8 1 4 0.4 2.9
Air filter element M6 × 1.0 1 2 0.2 1.4
Air filter case cover M6 × 1.0 4 4 0.4 2.9
Radiator panel (upper) M6 × 1.0 2 10 1.0 7.2
Radiator M6 × 1.0 6 10 1.0 7.2
Radiator hose clamp M6 × 1.0 8 2 0.2 1.4
Impeller M8 × 1.25 1 14 1.4 10
Water pump housing cover M6 × 1.0 3 10 1.0 7.2
Coolant drain bolt M6 × 1.0 1 10 1.0 7.2
Oil pump cover M5 × 0.8 1 4 0.4 2.9
Oil pump M6 × 1.0 3 10 1.0 7.2
Engine oil drain bolt (oil filter) M6 × 1.0 1 10 1.0 7.2
Oil filter cover M6 × 1.0 2 10 1.0 7.2
Oil delivery pipe 1 M10 × 1.25
M8 × 1.251
220
182.0
1.814
13
Oil hose clamp—2 2 0.2 1.4
Clutch cover M6 × 1.0 7 10 1.0 7.2
Crankcase cover (right) M6 × 1.0 10 10 1.0 7.2
Crankcase cover (left) M6 × 1.0 8 10 1.0 7.2
Crankcase M6 × 1.0 12 12 1.2 8.7

2 - 16
SPECMAINTENANCE SPECIFICATIONS (WR426F)
NOTE:
- marked portion shall be checked for torque tightening after break-in or before each race.Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Rear wheel axle and nut M20 × 1.5 1 125 12.5 90
Driven sprocket and wheel hub M8 × 1.25 6 42 4.2 30
Nipple (spoke)—72 3 0.3 2.2
Disc cover and rear brake caliper M6 × 1.0 2 7 0.7 5.1
Protector and rear brake caliper M6 × 1.0 2 7 0.7 5.1
Engine mounting:
Engine bracket and frame M8 × 1.25 7 34 3.4 24
Engine and frame (front) M10 × 1.25 1 69 6.9 50
Engine and frame (upper) M10 × 1.25 1 55 5.5 40
Engine and frame (lower) M10 × 1.25 1 69 6.9 50
Engine guard (left and right) M8 × 1.25 2 23 2.3 17
Pivot shaft and nut M16 × 1.5 1 85 8.5 61
Relay arm and swingarm M14 × 1.5 1 80 8.0 58
Relay arm and connecting rod M14 × 1.5 1 80 8.0 58
Connecting rod and frame M14 × 1.5 1 80 8.0 58
Rear shock absorber and frame M10 × 1.25 1 56 5.6 40
Rear shock absorber and relay arm M10 × 1.25 1 53 5.3 38
Rear frame and frame M8 × 1.25 3 29 2.9 21
Swingarm and brake hose holder M5 × 0.8 4 1 0.1 0.7
Swingarm and patch M4 × 0.7 4 2 0.2 1.4
Drive chain tensioner mounting (upper) M8 × 1.25 1 19 1.9 13
Drive chain tensioner mounting (lower) M8 × 1.25 1 20 2.0 14
Chain support and swingarm M6 × 1.0 3 7 0.7 5.1
Seal guard and swingarm M5 × 0.8 4 6 0.6 4.3
Fuel tank mounting M6 × 1.0 2 10 1.0 7.2
Fuel tank and fuel cock M6 × 1.0 2 7 0.7 5.1
Fuel tank and seat set bracket M6 × 1.0 1 7 0.7 5.1
Fuel tank and hooking screw (fitting band) M6 × 1.0 1 7 0.7 5.1
Fuel tank and fuel tank bracket M6 × 1.0 4 7 0.7 5.1
Seat mounting M8 × 1.25 2 23 2.3 17
Side cover mounting M6 × 1.0 2 7 0.7 5.1
Air scoop and fuel tank M6 × 1.0 4 4 0.4 2.9
Air scoop and radiator panel (lower) M6 × 1.0 2 4 0.4 2.9
Front fender mounting M6 × 1.0 4 7 0.7 5.1
Rear fender and air filter case M6 × 1.0 2 7 0.7 5.1
Rear fender and frame (right) M6 × 1.0 1 10 1.0 7.2
Headlight stay (lower) and under bracket M8 × 1.25 2 7 0.7 5.1
Headlight (left and right) M6 × 1.0 2 10 1.0 7.2
Headlight (lower) M6 × 1.0 1 7 0.7 5.1
Tail light M6 × 1.0 3 4 0.4 2.9
Tail light lead clamp and rear fender M4 × 1.59 2 1 0.1 0.7
Coolant reservoir tank (front) M6 × 1.0 1 7 0.7 5.1
Coolant reservoir tank (rear) M6 × 1.0 1 11 1.1 8.0
Sidestand bracket and frame M10 × 1.25 2 66 6.6 48
Sidestand mounting M10 × 1.25 1 64 6.4 46

2 - 18
SPECGENERAL SPECIFICATIONS (WR400F)
EC211000
GENERAL SPECIFICATIONS (WR400F)
Model name: WR400F (EUROPE)
WR400FP (AUS)
Model code number: 5GSA
Dimensions:
Overall length 2,171 mm (85.5 in)
Overall width 827 mm (32.6 in)
Overall height 1,303 mm (51.3 in)
Seat height 998 mm (39.3 in)
Wheelbase 1,490 mm (58.7 in)
Minimum ground clearance 373 mm (14.7 in)
Basic weight:
With oil and full fuel tank 121.5 kg (268 lb)
Engine:
Engine type Liquid cooled 4-stroke, DOHC
Cylinder arrangement Single cylinder, forward inclined
Displacement 399 cm
3 (14.1 Imp oz, 13.5 US oz)
Bore × stroke 92.0 × 60.1 mm (3.62 × 2.37 in)
Compression ratio 12.5 : 1
Starting system Kick starter
Lubrication system: Dry sump
Oil type or grade:
Engine oil
API “SH” or higher grade
Oil capacity:
Engine oil
Periodic oil change 1.3 L (1.14 Imp qt, 1.37 US qt)
With oil filter replacement 1.4 L (1.23 Imp qt, 1.48 US qt)
Total amount 1.5 L (1.32 Imp qt, 1.59 US qt)
Coolant capacity (including all routes): 1.2 L (1.06 Imp qt, 1.27 US qt)
Air filter: Wet type element
-20
-4-10
140
3010
5020
6830
8640 50
104
122°CTemp.
°F
10W-30
10W-40
20W-40
20W-50
15W-40

2 - 28
SPECMAINTENANCE SPECIFICATIONS (WR400F)
Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Spark plug M10S × 1.0 1 13 1.3 9.4
Camshaft cap M6 × 1.0 10 10 1.0 7.2
Cylinder head (stud bolt) M6 × 1.0 2 7 0.7 5.1
M8 × 1.25 3 15 1.5 11
(bolt) M10 × 1.25 4 44 4.4 32
(nut) M6 × 1.0 2 10 1.0 7.2
M8 × 1.25 2 20 2.0 14
Cylinder head cover M6 × 1.0 2 10 1.0 7.2
Cylinder M6 × 1.0 1 10 1.0 7.2
Timing chain tensioner M6 × 1.0 2 10 1.0 7.2
Tensioner cap bolt M6 × 1.0 1 7 0.7 5.1
Timing chain guide (rear) M6 × 1.0 2 10 1.0 7.2
Decompression shaft M6 × 1.0 1 7 0.7 5.1
Decompression cable guide M6 × 1.0 1 10 1.0 7.2
Exhaust pipe (nut) M8 × 1.25 1 13 1.3 9.4
(bolt) M8 × 1.25 1 24 2.4 17
Silencer M8 × 1.25 2 35 3.5 25
Silencer clamp M8 × 1.25 1 20 2.0 14
Exhaust pipe protector M6 × 1.0 3 10 1.0 7.2
Spark arrester (for USA) M6 × 1.0 3 10 1.0 7.2
Silencer end pipe (for USA) M6 × 1.0 1 10 1.0 7.2
Clamp (air cleaner joint) M5 × 0.8 1 3 0.3 2.2
Clamp (carburetor joint) M4 × 0.7 1 3 0.3 2.2
Air filter joint clamp M6 × 1.0 1 3 0.3 2.2
Throttle cable cover M5 × 0.8 1 4 0.4 2.9
Air filter element M6 × 1.0 1 2 0.2 1.4
Air filter case cover M6 × 1.0 4 4 0.4 2.9
Radiator panel (upper) M6 × 1.0 2 10 1.0 7.2
Radiator M6 × 1.0 6 10 1.0 7.2
Radiator hose clamp M6 × 1.0 8 2 0.2 1.4
Impeller M8 × 1.25 1 14 1.4 10
Water pump housing cover M6 × 1.0 3 10 1.0 7.2
Coolant drain bolt M6 × 1.0 1 10 1.0 7.2
Oil pump cover M5 × 0.8 1 4 0.4 2.9
Oil pump M6 × 1.0 3 10 1.0 7.2
Engine oil drain bolt (oil filter) M6 × 1.0 1 10 1.0 7.2
Oil filter cover M6 × 1.0 2 10 1.0 7.2
Oil delivery pipe 1 M10 × 1.25
M8 × 1.251
220
182.0
1.814
13
Oil hose clamp—2 2 0.2 1.4
Clutch cover M6 × 1.0 7 10 1.0 7.2
Crankcase cover (right) M6 × 1.0 10 10 1.0 7.2
Crankcase cover (left) M6 × 1.0 8 10 1.0 7.2
Crankcase M6 × 1.0 12 12 1.2 8.7

2 - 33
SPECMAINTENANCE SPECIFICATIONS (WR400F)
NOTE:
- marked portion shall be checked for torque tightening after break-in or before each race.Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Rear wheel axle and nut M20 × 1.5 1 125 12.5 90
Driven sprocket and wheel hub M8 × 1.25 6 42 4.2 30
Nipple (spoke)—72 3 0.3 2.2
Disc cover and rear brake caliper M6 × 1.0 2 7 0.7 5.1
Protector and rear brake caliper M6 × 1.0 2 7 0.7 5.1
Engine mounting:
Engine bracket and frame M8 × 1.25 7 34 3.4 24
Engine and frame (front) M10 × 1.25 1 69 6.9 50
Engine and frame (upper) M10 × 1.25 1 55 5.5 40
Engine and frame (lower) M10 × 1.25 1 69 6.9 50
Engine guard (left and right) M8 × 1.25 2 23 2.3 17
Pivot shaft and nut M16 × 1.5 1 85 8.5 61
Relay arm and swingarm M14 × 1.5 1 80 8.0 58
Relay arm and connecting rod M14 × 1.5 1 80 8.0 58
Connecting rod and frame M14 × 1.5 1 80 8.0 58
Rear shock absorber and frame M10 × 1.25 1 56 5.6 40
Rear shock absorber and relay arm M10 × 1.25 1 53 5.3 38
Rear frame and frame M8 × 1.25 3 29 2.9 21
Swingarm and brake hose holder M5 × 0.8 4 1 0.1 0.7
Swingarm and patch M4 × 0.7 4 2 0.2 1.4
Drive chain tensioner mounting (upper) M8 × 1.25 1 19 1.9 13
Drive chain tensioner mounting (lower) M8 × 1.25 1 20 2.0 14
Chain support and swingarm M6 × 1.0 3 7 0.7 5.1
Seal guard and swingarm M5 × 0.8 4 6 0.6 4.3
Fuel tank mounting M6 × 1.0 2 10 1.0 7.2
Fuel tank and fuel cock M6 × 1.0 2 7 0.7 5.1
Fuel tank and seat set bracket M6 × 1.0 1 7 0.7 5.1
Fuel tank and hooking screw (fitting band) M6 × 1.0 1 7 0.7 5.1
Fuel tank and fuel tank bracket M6 × 1.0 4 7 0.7 5.1
Seat mounting M8 × 1.25 2 23 2.3 17
Side cover mounting M6 × 1.0 2 7 0.7 5.1
Air scoop and fuel tank M6 × 1.0 4 4 0.4 2.9
Air scoop and radiator panel (lower) M6 × 1.0 2 4 0.4 2.9
Front fender mounting M6 × 1.0 4 7 0.7 5.1
Rear fender and air filter case M6 × 1.0 2 7 0.7 5.1
Rear fender and frame (right) M6 × 1.0 1 10 1.0 7.2
Headlight stay (lower) and under bracket M8 × 1.25 2 7 0.7 5.1
Headlight (left and right) M6 × 1.0 2 10 1.0 7.2
Headlight (lower) M6 × 1.0 1 7 0.7 5.1
Tail light M6 × 1.0 3 4 0.4 2.9
Tail light lead clamp and rear fender M4 × 1.59 2 1 0.1 0.7
Coolant reservoir tank (front) M6 × 1.0 1 7 0.7 5.1
Coolant reservoir tank (rear) M6 × 1.0 1 11 1.1 8.0
Sidestand bracket and frame M10 × 1.25 2 66 6.6 48
Sidestand mounting M10 × 1.25 1 64 6.4 46

2 - 38
SPECCABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1Hose guide
2Brake hose
3Regulator
4Fuel tank breather hose
5Oil tank breather hose
6Clamp
7Sub wire harness
8Tail light lead
9TPS (throttle position sensor) lead
0Neutral switch lead
AOil hose
BCylinder head breather hose
CHose holder
DCDI magneto lead
EClutch cable
FDecompression cable
GLights switch lead
HCarburetor breather hose
IOverflow hose
JCoolant reservoir tank breather hoseÅPass the fuel tank breather
hose behind handlebar, then
insert it into the steering shaft
hole.
ıPass the decompression
cable, regulator lead and lights
switch lead under where the oil
hose is attached.
ÇFasten the CDI magneto lead,
neutral switch lead and lights
switch lead to the frame with a
plastic locking tie.
ÎFasten the sub wire harness
and lights switch lead to the
frame in front of the protector
of the sub wire harness with a
plastic locking tie and cut off
the tie end.‰Pass the cylinder head
breather hose along the right
side of the oil tank breather
hose.
ÏFasten the sub wire harness
to the frame with a plastic
locking tie ends at the lower
left of the frame and cut off
the tie end. For fastening,
pass the plastic locking tie
through the upper holes in the
engine brackets.
ÌPass the sub wire harness
between the engine brackets.
ÓFasten the TPS lead (in the
sub wire harness) under the
frame so that it does not con-
tact the carburetor.

2 - 39
SPECCABLE ROUTING DIAGRAM
ÈMake sure that the TPS read
coupler does not go outside
the chassis.
ÔFasten the TPS lead under the
coupler to the frame with a
plastic locking tie.
Pass the carburetor breather
hoses and overflow hose
between the connecting rod
and cross tube (frame).
ÒFasten the neutral switch lead
and oil hose together with a
plastic locking tie and cut off
the tie end.
˜Fasten the cylinder head
breather hose with the hose
holder.
ˆFasten the neutral switch lead
to the frame with a plastic
band ends toward the rear of
the frame.ØFasten the neutral switch lead
and CDI magneto lead
together with a plastic band.
∏Pass the clutch cable through
the cable guide.
ŒPass the cylinder head
breather hose along the inner
side of the radiator pipe.
ÂPass the clutch cable between
the frame and radiator and
over the lower boss on the
radiator.
ÍPass the neutral switch lead
and CDI magneto lead through
the cable guide and over the
middle radiator mounting boss.
Then, pass the decompression
cable under the middle radia-
tor mounting boss and along
the left side of the neutral
switch lead and CDI magneto
lead.ÊPass the clutch cable through
the cable guide.
ËFit the brake hose into the
guides on the protector.
◊Fasten the ignition coil lead
(in the sub wire harness) on
the upper inside of the frame
and cut off the tie end.
„Pass the ignition coil lead (in
the sub wire harness) under
the cushion bracket (frame).
≈Fasten the ignition coil lead
(in the sub wire harness) to
the frame with a plastic lock-
ing tie and cut off the tie end.
ÁPass the carburetor breather
hoses, overflow hose and
coolant reservoir tank
breather hose so that all there
hoses do not contact the rear
shock absorber.