fuse YAMAHA WR 450F 2016 User Guide

CHARGING SYSTEM
9-14
EAS2GC1365TROUBLESHOOTING
The battery is not being charged.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left/right)1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the stator coil. Refer to “CHECKING THE STA-
TOR COIL” on page 9-76. NG

Replace the stator assembly.
OK 
4. Check the rectifier/regulator. Refer to “CHECKING THE RECTI-
FIER/REGULATOR” on page 9-76. NG

Replace the rectifier/regulator.
OK 
5. Check the entire charging system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-12. NG

Properly connect or repair the charging
system’s wiring.
OK 
This circuit is OK.

LIGHTING SYSTEM
9-17
1. Joint connector
2. Joint connector
6. Headlight relay
7. Main relay
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
22.ECU (engine control unit)
30.Joint connector
42.Joint connector
43.Taillight
44.Headlight
47.Multi-function display
48.Frame ground
50.Negative battery lead

LIGHTING SYSTEM
9-18
EAS2GC1367TROUBLESHOOTING
Any of the following fail to light: headlight or meter light.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left)
3. Air scoop (left/right)
4. Fuel tank1. Check the each bulbs condition. Refer to “CHECKING THE BULBS
AND BULB SOCKETS” on page 9-
67. NG

Replace the bulb (s).
OK 
2. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
3. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
4. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
5. Check the headlight relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the headlight relay.
OK 
6. Check the entire lighting system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-16. NG

Properly connect or repair the lighting sys-
tem’s wiring.
OK 
Replace the ECU, meter assembly, or
taillight.

SIGNALING SYSTEM
9-21
1. Joint connector
2. Joint connector
3. Joint connector
7. Main relay
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
15.Indicator light
17.Fuel level warning light
18.Resistor
19.Fuel sender
22.ECU (engine control unit)
30.Joint connector
42.Joint connector
46.Speed sensor
47.Multi-function display
48.Frame ground
50.Negative battery lead

SIGNALING SYSTEM
9-22
EAS2GC1369TROUBLESHOOTING
• The speedometer does not operate normally.
• The fuel indicator light does not come on.
TIP
Before troubleshooting, remove the following part (s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank
Check the signaling system
The speedometer fails to operate.
1. Check the fuse.Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
4. Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-20. NG

Properly connect or repair the signaling
system’s wiring.
OK 
This circuit is OK.
1. Check the speed sensor. Refer to “CHECKING THE SPEED
SENSOR” on page 9-77. NG

Replace the speed sensor.
OK 
2. Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-20. NG

Properly connect or repair the signaling
system’s wiring.
OK 
Replace the meter assembly.

COOLING SYSTEM
9-25
1. Joint connector
2. Joint connector
3. Joint connector
7. Main relay
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
22.ECU (engine control unit)
27.Radiator fan motor relay
28.Radiator fan motor fuse
29.Radiator fan motor
30.Joint connector
32.Coolant temperature sensor
48.Frame ground
50.Negative battery lead

COOLING SYSTEM
9-26
EAS2GC1372TROUBLESHOOTING
The radiator fan motor fails to turn.
TIP
Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left)
3. Air scoop (left/right)
4. Fuel tank1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the main relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the main relay.
OK 
4. Check the radiator fan motor. Refer to “CHECKING THE RADIA-
TOR FAN MOTOR” on page 9-78. NG

Replace the radiator fan motor.
OK 
5. Check the radiator fan motor relay. Refer to “CHECKING THE RE-
LAYS” on page 9-72. NG

Replace the radiator fan motor relay.
OK 
6. Check the coolant temperature sen- sor.
Refer to “CHECKING THE COOL-
ANT TEMPERATURE SENSOR”
on page 9-78. NG

Replace the coolant temperature sensor.
OK 
7. Check the entire cooling system’s wiring.
Refer to “CIRCUIT DIAGRAM” on
page 9-16. NG

Properly connect or repair the cooling sys-
tem’s wiring.
OK 
Replace the ECU.

FUEL INJECTION SYSTEM
9-29
1. Joint connector
2. Joint connector
3. Joint connector
4. AC magneto
7. Main relay
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
15.Indicator light
16.Engine trouble warning light
22.ECU (engine control unit)
25.Injector
30.Joint connector
31.Intake air temperature sensor
32.Coolant temperature sensor
33.Throttle position sensor
34.Intake air pressure sensor
35.Lean angle sensor
36.Engine stop switch
37.Neutral switch
38.Diode
39.Starting circuit cut-off relay
40.Clutch switch
42.Joint connector
48.Frame ground
50.Negative battery lead

FUEL PUMP SYSTEM
9-57
1. Joint connector
2. Joint connector
9. Battery
10.Frame ground
11.Starter relay
12.Main fuse
22.ECU (engine control unit)
26.Fuel pump
30.Joint connector
36.Engine stop switch
48.Frame ground
50.Negative battery lead

FUEL PUMP SYSTEM
9-58
EAS2GC1381TROUBLESHOOTING
The fuel pump fails to operate.
TIP
Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank1. Check the fuse. Refer to “CHECKING THE FUSES”
on page 9-68. NG

Replace the fuse(s).
OK 
2. Check the battery. Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 9-69. NG

• Clean the battery terminals.
• Recharge or replace the battery.
OK 
3. Check the engine stop switch. Refer to “CHECKING THE
SWITCHES” on page 9-64. NG

Replace the engine stop switch.
OK 
4. Check fuel pressure. Refer to “CHECKING THE FUEL
PRESSURE” on page 8-5. NG

Replace the fuel pump.
OK 
5. Check the fuel pump system wire harness connections.
Refer to “CIRCUIT DIAGRAM” on
page 9-56. NG

Properly connect or repair the fuel pump
system’s wiring.
OK 
Replace the ECU.