check oil YAMAHA XENTER 150 2012 User Guide

1
2
3
4
5
6
7
8
9
6-11
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, compres-
sion spring, O-ring and engine oil
drain bolt B.TIPMake sure that the O-ring is properly
seated.
7. Install engine oil drain bolt A, and
then tighten both drain bolts to
their specifi ed torques.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
32 Nm (3.2 m·kgf, 23.1 ft·lbf)8. Refill with the specified amount
of the recommended engine oil,
and then install and tighten the oil
fi ller cap.Recommended engine oil:
See page 8-1.
Oil change quantity:
1.10 L (1.16 US qt, 0.97 Imp.qt)
ECA11670
NOTICE● Do not use oils with a diesel
speci cation of “CD” or oils of
a higher quality than speci ed.
In addition, do not use oils la-
beled “ENERGY CONSERVING
II” or higher.● Be sure no foreign material en-
ters the crankcase. and B to drain the oil from the
crankcase.
NOTICE:
When re-
moving the engine oil drain
bolt B, the O-ring, compression
spring, and oil strainer will fall
out. Take care not to lose these
parts.
[ECAT1021]
1
1. Oil fi ller cap
1
1. Engine oil drain bolt A
52S-F8199-E0_CS.indd 6-1152S-F8199-E0_CS.indd 6-11
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-12
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
1
1. Final transmission oil fi ller cap4. Remove the fi nal transmission oil
filler cap and its O-ring from the
fi nal transmission case.
5. Remove the fi nal transmission oil
drain bolt and its gasket to drain
the oil from the fi nal transmission
case.
EAU20065
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the fi nal transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm up the fi -
nal transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the center-
stand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
9. Start the engine, and then let
it idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the en-
gine off and check for the cause.
10. Turn the engine off, and then
check the oil level and correct it if
necessary.
To reset the oil change indicator
and oil change tripmeterTIPThe oil change indicator and oil
change tripmeter can be reset when
“OIL CHANGE” and “OIL TRIP” ap-
pear in the multi-function display. (see
page 3-3.)
52S-F8199-E0_CS.indd 6-1252S-F8199-E0_CS.indd 6-12
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-13
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.2 L (0.21 US qt, 0.18 Imp.qt)8. Install the final transmission oil
fi ller cap and its new O-ring, and
then tighten the oil fi ller cap.
9. Check the fi nal transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAU20070
CoolantThe coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specifi ed in the periodic maintenance
and lubrication chart.
EAUT3690
To check the coolant level
The coolant level should be checked
as follows before each ride. In addi-
tion, the coolant must be changed at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Place the vehicle on the center-
stand.TIP● The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.● Make sure that the vehicle is po-
sitioned straight up when check-
ing the coolant level. A slight tilt
to the side can result in a false
1
1. Final transmission oil drain bolt6. Install the final transmission oil
drain bolt and its new gasket, and
then tighten the bolt to the speci-
fi ed torque.Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)7. Refi ll with the specifi ed amount of
the recommended fi nal transmis-
sion oil. WARNING! Make sure
that no foreign material enters
the final transmission case.
Make sure that no oil gets on
the tire or wheel.
[EWA11311]
52S-F8199-E0_CS.indd 6-1352S-F8199-E0_CS.indd 6-13
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-21
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
tem, reducing braking perfor-
mance.
● Clean the filler cap before re-
moving. Use only DOT 4 brake
uid from a sealed container.● Use only the specified brake
fluid; otherwise, the rubber
seals may deteriorate, causing
leakage.● Refill with the same type of
brake uid. Adding a brake u-
id other than DOT 4 may result
in a harmful chemical reaction.● Be careful that water does not
enter the brake fluid reser-
voir when refilling. Water will
significantly lower the boiling
point of the fluid and may re-
sult in vapor lock.
ECA17640
NOTICEBrake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled uid immediately.
As the brake pads wear, it is normal
for the brake fluid level to gradually
EAU32345
Checking the brake uid level
1
1. Minimum level markBefore riding, check that the brake
fl uid is above the minimum level mark.
Check the brake fluid level with the
top of the reservoir level. Replenish
the brake fl uid if necessary.Speci ed brake uid:
DOT 4
EWA15990
WARNING
Improper maintenance can result
in loss of braking ability. Observe
these precautions:● Insufficient brake fluid may al-
low air to enter the brake sys- shoes as a set.
52S-F8199-E0_CS.indd 6-2152S-F8199-E0_CS.indd 6-21
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-22
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23095
Checking and lubricating the
cablesThe operation of all control cables
and the condition of the cables should
be checked before each ride, and
the cables and cable ends should be
lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or re-
place it. WARNING! Damage to the
outer housing of cables may result
in internal rusting and cause in-
terference with cable movement.
Replace damaged cables as soon
as possible to prevent unsafe
conditions.
[EWA10711]
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
EAU22721
Changing the brake uidHave a Yamaha dealer change the
brake fl uid at the intervals specifi ed in
the TIP after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cyl-
inder and caliper as well as the brake
hose replaced at the intervals listed
below or whenever they are damaged
or leaking.● Oil seals: Replace every two
years.● Brake hose: Replace every four
years. go down. A low brake fl uid level may
indicate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fl uid level goes down suddenly, have
a Yamaha dealer check the cause be-
fore further riding.
52S-F8199-E0_CS.indd 6-2252S-F8199-E0_CS.indd 6-22
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-24
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
ECA10590
NOTICEIf any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU23272
Checking the front forkThe condition and operation of the
front fork must be checked as follows
at the intervals specifi ed in the period-
ic maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-
face and hold it in an upright
position. WARNING! To avoid
injury, securely support the ve-
hicle so there is no danger of it
falling over.
[EWA10751]
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
loss of control.Recommended lubricant:
Lithium-soap-based grease
52S-F8199-E0_CS.indd 6-2452S-F8199-E0_CS.indd 6-24
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-28
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT3660
Replacing a headlight bulbThis model is equipped with a halo-
gen bulb headlight. If a headlight bulb
burns out, replace it as follows.
ECA10650
NOTICETake care not to damage the follow-
ing parts:●
Headlight bulb
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency
of the glass, the luminosity of the
bulb, and the bulb life will be ad-
versely affected. Thoroughly clean
off any dirt and ngerprints on the
headlight bulb using a cloth moist-
ened with alcohol or thinner.
●
Headlight lens
• Do not affix any type of
tinted film or stickers to the
headlight lens.
• Do not use a headlight bulb
of a wattage higher than
speci ed.1. Remove cowling A together with
the headlight unit. (See page
6-7.)
2. Remove the bulb cover, and then
disconnect the headlight coupler.
1
1. Headlight bulb cover
1
2
3
1. Headlight coupler
2. Headlight bulb holder
3. Headlight bulb
Speci ed fuses:
Main fuse:
20 A
Ignition fuse:
7.5 A
Signaling system fuse:
15 A
Headlight fuse:
15 A
Backup fuse:
7.5 ATIPAfter removing and installing the main
fuse, be sure to turn the main switch
from “ON” to “OFF” three times in
three-second intervals to initialize the
idle speed control system.
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
52S-F8199-E0_CS.indd 6-2852S-F8199-E0_CS.indd 6-28
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
7-4
EAU25991
SCOOTER CARE AND STORAGE
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING!
To prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10951]
4. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then
lift the scooter so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degraded
in one spot.
6. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully
charge it. Store it in a cool,
dry place and charge it once a
month. Do not store the battery
in an excessively cold or warm
place [less than 0 °C (30 °F) or
more than 30 °C (90 °F)]. For
more information on storing the
battery, see page 6-26.
TIPMake any necessary repairs before
storing the scooter.
52S-F8199-E0_CS.indd 7-452S-F8199-E0_CS.indd 7-4
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

INDEXAAcceleration and deceleration ................... 5-2
Air fi lter and V-belt case air fi lter
elements ............................................... 6-15
Auxiliary light bulb, replacing .................. 6-30BBattery ..................................................... 6-25
Brake fl uid, changing .............................. 6-22
Brake fl uid level, checking ...................... 6-21
Brake lever, front ....................................... 3-7
Brake lever, rear ....................................... 3-8
Brake levers, lubricating .......................... 6-23
Brake pads and shoes, checking ............ 6-20
Braking ...................................................... 5-2CCables, checking and lubricating ............ 6-22
Care .......................................................... 7-1
Carrier ..................................................... 3-14
Catalytic converter .................................. 3-10
Centerstand, checking and lubricating .... 6-23
Coolant .................................................... 6-13
Coolant temperature warning light ............ 3-2
Cowling and panels, removing and
installing .................................................. 6-7DDimmer switch .......................................... 3-7EEngine break-in ......................................... 5-3
Engine idling speed, checking ................ 6-16
Engine oil ................................................ 6-10
Engine trouble warning light ...................... 3-3FFinal transmission oil .............................. 6-12
Front brake lever free play, checking ...... 6-19Front fork, checking ................................ 6-24
Fuel ........................................................... 3-9
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................ 3-8
Fuses, replacing ...................................... 6-27
HHandlebar switches ................................... 3-7
Headlight bulb, replacing ........................ 6-28
High beam indicator light .......................... 3-2
Horn switch ............................................... 3-7IIdentifi cation numbers ............................... 9-1
Indicator lights and warning lights ............. 3-2LLicense plate light ................................... 6-31
Luggage holder ....................................... 3-14MMaintenance, emission control system ..... 6-3
Maintenance and lubrication, periodic ...... 6-4
Main switch/steering lock .......................... 3-1
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................ 3-3PParking ...................................................... 5-4
Part locations ............................................ 2-1
Passenger footrest .................................. 3-12RRear brake lever free play, adjusting ...... 6-19SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-11
Shock absorber assembly ....................... 3-13Spark plug, checking ................................. 6-9
Specifi cations ............................................ 8-1
Starting off ................................................. 5-2
Starting the engine .................................... 5-1
Start switch ............................................... 3-7
Steering, checking .................................. 6-25
Storage ..................................................... 7-3
Storage compartment (front) ................... 3-12
Storage compartment (rear) .................... 3-13
TTail/brake light ......................................... 6-29
Throttle grip and cable, checking and
lubricating ............................................. 6-23
Throttle grip free play, checking .............. 6-16
Tires ........................................................ 6-17
Tool kit ...................................................... 6-2
Troubleshooting ...................................... 6-32
Troubleshooting charts ........................... 6-33
Turn signal indicator lights ........................ 3-2
Turn signal light bulb (front), replacing .... 6-29
Turn signal light bulb (rear), replacing .... 6-31
Turn signal switch ..................................... 3-7VValve clearance ...................................... 6-17
Vehicle identifi cation number .................... 9-1WWheels .................................................... 6-19
Wheel bearings, checking ....................... 6-25
52S-F8199-E0_CS.indd 9-252S-F8199-E0_CS.indd 9-2
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black