brake YAMAHA XENTER 150 2016 Owner's Manual

Periodic maintenance and adjustment
6-23
1
2
3
4
56
7
8
9
10
11
12 check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before
further riding.
EAU22724
Changing the brake fluid Have a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil seals
of the brake master cylinder and caliper
as well as the brake hose replaced at
the intervals listed below or whenever
they are damaged or leaking.
Oil seals: Replace every two
years.

Brake hose: Replace every four
years.
EAU23098
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING! Damage to the outer
housing of cables may result in in-
ternal rusting and cause interfer-
ence with cable movement. Replace
damaged cables as soon as possi-
ble to prevent unsafe condi-
tions.
[EWA10712]
Recommended lubricant:
Yamaha cable lubricant or other suit-
able cable lubricant
U52SE1E0 23 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment6-24
1
2
3
4
567
8
9
10
11
12
EAU23115
Checking and lubricating the
throttle grip and cableThe operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated by a
Yamaha dealer at the intervals speci-
fied in the periodic maintenance chart.
The throttle cable is equipped with a
rubber cover. Make sure that the cover
is securely installed. Even though the
cover is installed correctly, it does not
completely protect the cable from water
entry. Therefore, use care not to pour
water directly onto the cover or cable
when washing the vehicle. If the cable
or cover becomes dirty, wipe clean with
a moist cloth.
EAUT3571
Lubricating the front and rear
brake leversFront and rear brake levers
The pivoting points of the front and rear
brake levers should be lubricated by a
Yamaha dealer at the intervals speci-
fied in the periodic maintenance and lu-
brication chart.
EAU23193
Checking and lubricating the
centerstandThe operation of the centerstand
should be checked before each ride,
and the pivots and metal-to-metal con-
tact surfaces should be lubricated if
necessary.
WARNING
EWA11302
If the centerstand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the centerstand could contact the
ground and distract the operator, re-sulting in a possible loss of control.1. Centerstand
1
U52SE1E0 24 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment
6-25
1
2
3
4
56
7
8
9
10
11
12
EAU23273
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake, push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-pair it.
Recommended lubricant:Lithium-soap-based grease
U52SE1E0 25 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment6-30
1
2
3
4
567
8
9
10
11
12
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the cowling.
EAU24182
Tail/brake lightThis model is equipped with an
LED-type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
EAUT3652
Replacing a front turn signal
light bulbIf a front turn signal light burns out, re-
place it as follows. 1. Remove cowling A. (See page 6-8.)
2. Remove the socket (together with the bulb) by turning it counter-
clockwise.
3. Remove the burnt out bulb by pushing it in and turning it counter-
clockwise.
1. Auxiliary light bulb
1
1. Turn signal light bulb socket
1
U52SE1E0 30 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Scooter care and storage
7-2
1
2
3
4
5
678
9
10
11
12
plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid- den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.TIPSalt sprayed on roads in the winter may
remain well into spring. 1. Clean the scooter with cold water and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
Cleaning the windshieldAvoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield with
a cloth or sponge dampened with a mild
detergent, and then wash it off thor-
oughly with water. For additional clean-
ing, use Yamaha Windshield Cleaner
or another high-quality windshield
cleaner. Some cleaning compounds for
plastics may leave scratches on the
windshield. Before using such clean-
ers, test an area of the windshield
which does not affect your visibility and
which cannot be easily recognized.
U52SE1E0 2 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Scooter care and storage
7-3
1
2
3
4
5
67
8
9
10
11
12 After cleaning
1. Dry the scooter with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean- er to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be- fore storing or covering it.
WARNING
EWA10943
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent.

Before operating the scooter
test its braking performanceand cornering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
U52SE1E0 3 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Specifications
8-2
1
2
3
4
5
6
789
10
11
12
Manufacturer/model: DURO / DM1157FRear tire:Type:Tubeless
Size: 120 / 80 - 16M/C 60P
Manufacturer/model:
DURO / DM1157Loading:Maximum load:179 kg (395 lb)
* (Total weight of rider, passenger, cargo
and accessories)Tire air pressure (measured on cold
tires):Loading condition:90 kg (198 lb)
Front: 175 kPa (1.75 kgf/cm
2, 25 psi)
Rear: 200 kPa (2.00 kgf/cm2, 29 psi)
Loading condition:
90 kg - maximum load
Front: 175 kPa (1.75 kgf/cm2, 25 psi)
Rear: 225 kPa (2.25 kgf/cm2, 33 psi)
Front wheel:Wheel type:Cast wheel
Rim size: J 16M/C × MT2.50
Rear wheel:Wheel type:Cast wheel
Rim size: J 16M/C × MT2.75Front brake:Type:
Hydraulic single disc brake
Specified brake fluid: DOT 4Rear brake:Type:
Mechanical leading trailing drum brakeFront suspension:Type:Telescopic fork
Spring:
Coil spring
Shock absorber: Hydraulic damper
Wheel travel: 100 mm (3.9 in)Rear suspension:Type:Unit swing
Spring: Coil spring
Shock absorber:
Gas-hydraulic damper
Wheel travel: 92 mm (3.6 in)Electrical system:System voltage:
12 V Ignition system:
TCI
Charging system:
AC magneto
Battery:Model:GT7B-4
Voltage, capacity:
10 V, 6.5 Ah (10 HR)Headlight:Bulb type:Halogen bulbBulb voltage, wattage  quantity:Headlight:
12 V, 55.0 W  2
Brake/tail light: LED
Front turn signal light:
12 V, 10.0 W  2
Rear turn signal light: 12 V, 10.0 W  2
Auxiliary light: 12 V, 5.0 W  2
License plate light:
12 V, 5.0 W  1
Meter lighting: LED
High beam indicator light: LED
Turn signal indicator light:
LED
Coolant temperature warning light: LED
U52SE1E0 2 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Index
AAcceleration and deceleration ................... 5-2
Air filter and V-belt case air filter
elements ................................................ 6-16
Auxiliary light bulb, replacing ................... 6-29BBattery ..................................................... 6-26
Brake fluid, changing ............................... 6-23
Brake fluid level, checking ....................... 6-22
Brake lever, front ....................................... 3-7
Brake lever, rear ........................................ 3-8
Brake levers, lubricating .......................... 6-24
Brake pads and shoes, checking............. 6-21
Braking ...................................................... 5-3CCables, checking and lubricating ............. 6-23
Care ........................................................... 7-1
Carrier...................................................... 3-14
Catalytic converter ................................... 3-10
Centerstand, checking and lubricating .... 6-24
Coolant .................................................... 6-14
Coolant temperature warning light............. 3-2
Cowling and panels, removing and installing .................................................. 6-8DDimmer switch ........................................... 3-7EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-17
Engine oil ................................................. 6-11
Engine serial number................................. 9-1
Engine trouble warning light ...................... 3-3FFinal transmission oil ............................... 6-13 Front brake lever free play, checking ...... 6-20
Front fork, checking................................. 6-25
Fuel ........................................................... 3-9
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap............................................. 3-8
Fuses, replacing ...................................... 6-28
HHandlebar switches ................................... 3-7
Headlight bulb, replacing......................... 6-28
High beam indicator light........................... 3-2
Horn switch ............................................... 3-7IIdentification numbers ............................... 9-1
Indicator lights and warning lights ............. 3-2LLicense plate light ................................... 6-32
Luggage holder ....................................... 3-14MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-5
Maintenance, emission control system ..... 6-4
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function display................................. 3-3PParking ...................................................... 5-4
Part locations ............................................ 2-1
Passenger footrest .................................. 3-11RRear brake lever free play, adjusting ...... 6-20SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-11 Shock absorber assembly .......................3-13
Spark plug, checking ...............................6-10
Specifications.............................................8-1
Starting off .................................................5-2
Starting the engine.....................................5-1
Start switch ................................................3-7
Steering, checking ...................................6-26
Storage ......................................................7-4
Storage compartments ............................3-12
TTail/brake light ......................................... 6-30
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking...............6-17
Tires .........................................................6-18
Tool kit .......................................................6-2
Troubleshooting .......................................6-32
Troubleshooting charts ............................6-33
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-30
Turn signal light bulb (r ear), replacing .....6-31
Turn signal switch ......................................3-7VValve clearance .......................................6-18
Vehicle identificat ion number .....................9-1WWheel bearings, checking........................6-26
Wheels .....................................................6-20
U52SE1E0 1 ページ ２０１５年９月１６日　水曜日　午後５時２７分