light YAMAHA XJ600S 2001 Owner's Manual

PERIODIC MAINTENANCE AND MINOR REPAIR
6-19
6
EAU00713
Adjusting the rear brake light
switch The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction
a. To
make the brake light come on later,
turn the adjusting nut in direction
b.
EAU00721
Checking the front and rear
brake pads The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.
EAU00725
Front brake pads
Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear
indicator groove has almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.
1. Brake light switch
2. Brake light switch adjusting nut
1. Wear indicator groove (´ 2)Front
E_4br.book Page 19 Thursday, August 17, 2000 11:29 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
6
EAU01470
Replacing the fuses The fuse box is located under the seat.
(See page 3-12 for seat removal and
installation procedures.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
EC000103
CAUTION:@ Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire. @3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
1. Fuse box
1. Main fuse
2. Ignition fuse
3. Signaling system fuse
4. Headlight fuse
5. Hazard fuse
6. Spare fuse (´ 3)
Specified fuses:
Main fuse: 30 A
Ignition fuse: 10 A
Signaling system fuse: 15 A
Headlight fuse: 15 A
Hazard fuse: 10 A
E_4br.book Page 29 Thursday, August 17, 2000 11:29 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6
EAU00829
Replacing a headlight bulb
(for XJ600S)This motorcycle is equipped with
quartz bulb headlights. If a headlight
bulb burns out, replace it as follows.
1. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.2. Unhook the headlight bulb holder,
and then remove the defective
bulb.
EW000119
WARNING
@ Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. @
3. Place a new bulb into position, and
then secure it with the bulb holder.
EC000105
CAUTION:@ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. @
1. Headlight coupler
2. Headlight bulb cover
1. Headlight bulb holder
1. Do not touch this area.
E_4br.book Page 30 Thursday, August 17, 2000 11:29 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
64. Install the bulb cover, and then
connect the coupler.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU03188
Replacing the headlight bulb
(for XJ600N)This motorcycle is equipped with a
quartz bulb headlight. If the headlight
bulb burns out, replace it as follows.
1. Remove the headlight unit by re-
moving the screws.2. Disconnect the headlight coupler,
and then remove the headlight unit
and bulb cover.1. Screw (´ 2)
1. Headlight coupler
2. Headlight bulb cover
E_4br.book Page 31 Thursday, August 17, 2000 11:29 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
6 3. Unhook the headlight bulb holder,
and then remove the defective
bulb.
EW000119
WARNING
@ Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. @
4. Place a new bulb into position, and
then secure it with the bulb holder.
EC000105
CAUTION:@ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. @
5. Install the bulb cover, and then
connect the coupler.
6. Install the headlight unit by install-
ing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight bulb holder
1. Do not touch this area.
E_4br.book Page 32 Thursday, August 17, 2000 11:29 AM

MOTORCYCLE CARE AND STORAGE
7-2
7
l
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
l
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments, switch-
es and lights), breather hoses
and vents.
l
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
@After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:@ Salt sprayed on roads in the winter may
remain well into spring. @1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:@ Do not use warm water since it in-
creases the corrosive action of the
salt. @2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
E_4br.book Page 2 Thursday, August 17, 2000 11:29 AM

SPECIFICATIONS
8-4
8
Charging system
Type A.C. magneto
Standard output 14 V, 20 A @ 5,000 r/min
Battery
Model YTX9-BS
Voltage, capacity 12 V, 8 Ah
Headlight typeQuar tz bulb (halogen)
Bulb voltage, wattage ´ quantity
Headlight 12 V, 60/55 W ´ 1
Auxiliary light 12 V, 4 W ´ 1 (except for GB,
IRL)
12 V, 3.4 W ´ 1 (for GB, IRL)
Tail/brake light 12 V, 5/21 W ´ 1
Turn signal light 12 V, 21 W ´ 4
Meter lighting
XJ600S 12 V, 1.7 W ´ 3
XJ600N 14 V, 3 W ´ 2
12 V, 1.7 W ´ 2
Neutral indicator light 12 V, 3.4 W ´ 1
High beam indicator light 12 V, 3.4 W ´ 1
Oil level warning light
XJ600S 12 V, 3.4 W ´ 1
XJ600N 14 V, 3 W ´ 1
Turn signal indicator light 12 V, 3.4 W ´ 2Fuses
Main fuse 30 A
Ignition fuse 10 A
Signaling system fuse 15 A
Headlight fuse 15 A
Hazard fuse 10 A
E_4br.book Page 4 Thursday, August 17, 2000 11:29 AM

10-INDEXAAir filter element, cleaning ...................... 6-10BBattery ................................................... 6-27
Brake and clutch levers, checking and
lubricating ............................................ 6-25
Brake and shift pedals, checking and
lubricating ............................................ 6-24
Brake fluid, changing ............................. 6-21
Brake fluid level, checking...................... 6-20
Brake lever...............................................3-8
Brake light switch (rear), adjusting ......... 6-19
Brake pads, checking............................. 6-19
Brake pedal..............................................3-9
Brake pedal position, adjusting .............. 6-18CCables, checking and lubricating............ 6-23
Carburetors, adjusting............................ 6-12
Care.........................................................7-1
Centerstand and sidestand, checking
and lubricating ..................................... 6-25
Clutch lever ..............................................3-7
Clutch lever free play, adjusting ............. 6-17
Controls and instruments (XJ600N) .........2-6
Controls and instruments (XJ600S)..........2-3
Conversion table ......................................8-5DDimmer switch .........................................3-6
Drive chain, lubricating ........................... 6-23
Drive chain slack ................................... 6-21
Adjusting .......................................... 6-22
Checking .......................................... 6-21EEngine break-in ....................................... 5-4
Engine oil and oil filter cartridge ............... 6-7
Engine stop switch................................... 3-7FFront fork, checking ............................... 6-26
Front wheel ........................................... 6-33
Installing........................................... 6-33
Removing......................................... 6-33
Fuel ....................................................... 3-10
Fuel cock ............................................... 3-11
Fuel consumption, tips for reducing ......... 5-4
Fuel tank breather hose
(Germany only) ................................... 3-10
Fuel tank cap ........................................... 3-9
Fuses, replacing .................................... 6-29HHandlebar switches ................................. 3-6
Hazard switch .......................................... 3-6
Headlight bulb, replacing (for XJ600N) .. 6-31
Headlight bulb, replacing (for XJ600S) .. 6-30
Helmet holders ...................................... 3-13
High beam indicator light ......................... 3-4
Horn switch ............................................. 3-6IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-13
Ignition circuit cut-off system ..................3-16
Indicator lights ..........................................3-3KKey identification number (for XJ600N) ....9-1
Key identification number (for XJ600S) ....9-1LLeft view (XJ600N) ...................................2-4
Left view (XJ600S) ...................................2-1
Light switch ..............................................3-7
Luggage strap holders ...........................3-15NNeutral indicator light ...............................3-3MMain switch/steering lock .........................3-1
Maintenance and lubrication, periodic ......6-2
Model label ..............................................9-2OOperation .................................................5-1
Oil level warning light ...............................3-4PPass switch ..............................................3-6
Panel, removing and installing..................6-5
Parking.....................................................5-5
Part locations ...........................................2-1
Pre-operation check list ............................4-1RRear wheel.............................................6-35
Installing...........................................6-36
Removing .........................................6-35
E_4br.book Page 1 Thursday, August 17, 2000 11:29 AM

INDEX
Right view (XJ600N) ................................ 2-5
Right view (XJ600S) ................................ 2-2SSafety information.................................... 1-1
Seat....................................................... 3-12
Shifting .................................................... 5-3
Shift pedal ............................................... 3-8
Shift points (for Switzerland only)............. 5-3
Shock absorber assembly, adjusting ..... 3-14
Sidestand .............................................. 3-15
Spark plugs, checking ............................. 6-6
Specifications .......................................... 8-1
Speedometer unit (for XJ600N) ............... 3-5
Speedometer unit (for XJ600S) ............... 3-4
Starter (choke) lever .............................. 3-12
Starting a cold engine .............................. 5-1
Starting a warm engine ............................ 5-2
Start switch .............................................. 3-7
Steering, checking ................................. 6-26
Steering lock (for XJ600N)....................... 3-3
Storage.................................................... 7-4
Storage compartment ............................ 3-13
Suspension (rear), lubricating ................ 6-25TTachometer ............................................. 3-5
Throttle cable free play, adjusting .......... 6-13
Throttle grip and cable, checking and
lubricating............................................ 6-24
Tires ...................................................... 6-14
Tool kit..................................................... 6-1
Troubleshooting..................................... 6-36
Troubleshooting chart ............................ 6-37
Turn signal indicator lights ....................... 3-3
Turn signal switch ................................... 3-6VValve clearance, adjusting .................... 6-14
Vehicle identification number................... 9-2WWheel bearings, checking ..................... 6-27
Wheels .................................................. 6-17
E_4br.book Page 2 Thursday, August 17, 2000 11:29 AM