check oil YAMAHA XMAX 125 2012 Owners Manual

SAFETY INFORMATION .....................1-1
Further safe-riding points .................1-5
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-3
Controls and instruments .................2-5
INSTRUMENT AND CONTROL
FUNCTIONS ........................................3-1
Immobilizer system ...........................3-1
Main switch/steering lock .................3-2
Indicator and warning lights .............3-4
Turn signal indicator lights ...............3-4
High beam indicator light ................3-4
Engine trouble warning light ............3-4
ABS warning light
(for ABS models) ...........................3-4
Immobilizer system indicator light ....3-5
Speedometer ....................................3-5
Tachometer .......................................3-6
Multi-function display .......................3-6
Anti-theft alarm (optional) ...............3-11
Handlebar switches ........................3-11
Pass switch ....................................3-12
Dimmer switch ...............................3-12
Turn signal switch ..........................3-12
Horn switch ...................................3-12
Start switch ....................................3-12
Hazard switch ................................3-12
Front brake lever.............................3-12Rear brake lever..............................3-13
ABS (for ABS models) ....................3-13
Fuel tank cap ..................................3-14
Fuel .................................................3-15
Catalytic converters ........................3-16
Securing bracket ............................3-17
Seat.................................................3-17
Storage compartments ...................3-18
Adjusting the shock absorber
assemblies...................................3-19
Travel trunk .....................................3-20
Sidestand ........................................3-22
Ignition circuit cut-off system .........3-22
FOR YOUR SAFETY –
PRE-OPERATION CHECKS ...............4-1
OPERATION AND IMPORTANT
RIDING POINTS ..................................5-1
Starting the engine ...........................5-1
Starting off ........................................5-2
Acceleration and deceleration ..........5-3
Braking..............................................5-3
Tips for reducing fuel
consumption..................................5-4
Engine break-in.................................5-4
Parking ..............................................5-5
PERIODIC MAINTENANCE AND
ADJUSTMENT ....................................6-1
Owner’s tool kit .................................6-2Periodic maintenance chart for the
emission control system ...............6-3
General maintenance and lubrication
chart ..............................................6-4
Removing and installing the cowling
and panel.......................................6-8
Checking the spark plug ..................6-9
Engine oil ........................................6-10
Final transmission oil ......................6-13
Coolant ...........................................6-14
Air filter and V-belt case air filter
elements ......................................6-16
Adjusting the throttle cable free
play ..............................................6-17
Valve clearance ...............................6-18
Tires ................................................6-18
Cast wheels ....................................6-20
Checking the front and rear brake
lever free play ..............................6-20
Checking the front and rear brake
pads.............................................6-21
Checking the brake fluid level ........6-22
Changing the brake fluid ................6-23
Checking and lubricating the
throttle grip and cable .................6-23
Lubricating the front and rear
brake levers .................................6-24
Checking and lubricating the
centerstand and sidestand .........6-24
Checking the front fork ...................6-25
Checking the steering.....................6-26
TABLE OF CONTENTS

EAU10420
Right view
YP125R/YP125RA
DESCRIPTION
2-3
2
1. Grab bar (page 5-2)
2. Seat (page 3-17)
3. Coolant reservoir cap (page 6-14)
4. Battery (page 6-26)
5. Fuses (page 6-28)
6. Front brake pads (page 6-21)
7. Coolant level check window (page 6-14)
8. Engine oil filler cap (page 6-10)9. Rear brake pads (page 6-21)
10. Shock absorber assembly spring preload adjusting ring (page 3-19)

YP125RA Business Edition / YP125R Sports
DESCRIPTION
2-4
2
1. Grab bar (page 5-2)
2. Seat (page 3-17)
3. Coolant reservoir cap (page 6-14)
4. Battery (page 6-26)
5. Fuses (page 6-28)
6. Front brake pads (page 6-21)
7. Coolant level check window (page 6-14)
8. Engine oil filler cap (page 6-10)9. Rear brake pads (page 6-21)
10. Shock absorber assembly spring preload adjusting ring (page 3-19)

If the engine oil is changed before the
oil change indicator comes on (i.e.
before the periodic oil change interval
has been reached), the indicator must
be reset after the oil change for the
next periodic oil change to be indica-
ted at the correct time. (See page
6-10).
The electrical circuit of the indicator
can be checked according to the
following procedure.
1. Turn the key to “ON”.
2. Check that the indicator comes
on for a few seconds and then
goes off.
3. If the indicator does not come on,
have a Yamaha dealer check the
electrical circuit.
V-belt replacement indicator “V-
BELT”
This indicator flashes every 18000 km
(10500 mi) when the V-belt needs to
be replaced.
The electrical circuit of the indicator
can be checked according to the
following procedure.
1. Turn the key to “ON”.2. Check that the indicator comes
on for a few seconds and then
goes off.
3. If the indicator does not come on,
have a Yamaha dealer check the
electrical circuit.
Self-diagnosis device
This model is equipped with a self-
diagnosis device for various electrical
circuits.
If a problem is detected in any of tho-
se circuits, the multi-function display
will indicate an error code.
If the multi-function display indicates
such an error code, note the code
number, and then have a Yamaha
dealer check the vehicle.
ECA11790
If the multi-function display indica-
tes an error code, the vehicle
should be checked as soon as pos-
sible in order to avoid engine
damage.
The self-diagnosis device also
detects problems in the immobilizer
system circuits.If a problem is detected in the immo-
bilizer system circuits, the immobilizer
system indicator light will flash and
the multi-function display will indicate
an error code when the key is turned
to “ON”.
TIP
If the multi-function display indicates
error code 52, this could be caused
by transponder interference. If this
error appears, try the following.
1. Error code display
1. Use the code re-registering key
to start the engine.
TIP
Make sure there are no other immobi-
NOTICE
INSTRUMENT AND CONTROL FUNCTIONS
3-9
3

FOR YOUR SAFETY – PRE-OPERATION CHECKS
4-1
4
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the ins-
pection and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment dama-
ge. Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures pro-
vided in this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
WARNING
ITEM CHECKS PAGE

Fuel3-15


Engine oil 6-10

Final transmission oil 6-13

Coolant 6-14




Front brake 6-20, 6-21, 6-22

PERIODIC MAINTENANCE AND ADJUSTMENT
6-5
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 6000 km 12000 km 18000 km 24000 kmCHECK
(600 mi) (3500 mi) (7000 mi) (10500 mi) (14000 mi)

9*Steering bearingsfor roughness.33 3 3 3

based grease.Every 24000 km (14000 mi)
10 *Chassis fasteners
screws are properly tightened.333 33
11Front brake lever
pivot shaft333 33
12Rear brake lever
pivot shaft333 33
Sidestand,
13 333 33
centerstand
based grease.
14 *Sidestand switch33 3 3 3 3
15 *Front fork
leakage.333 3
16 *Shock absorber
assembliesabsorbers for oil leakage.333 3
When the oil change indicator flashes [5000 km (3000 mi)
3after the initial 1000 km (600 mi) and every 6000 km
17Engine oiland 6-10.)
(3500 mi) thereafter]

leakage.Every 3000 km (1800 mi)3
18Engine oil filter
element33 3

PERIODIC MAINTENANCE AND ADJUSTMENT
6-6
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 6000 km 12000 km 18000 km 24000 kmCHECK
(600 mi) (3500 mi) (7000 mi) (10500 mi) (14000 mi)

19 *Cooling systemfor coolant leakage.333 33
Every 3 years
20Final transmission 33 3oil
33 3
21 *V-beltWhen the V-belt replacement indicator flashes
[every 18000 km (10500 mi)]
22 *Front and rear brake
switches33 3 3 3
3
23Moving parts and
cables333 3
3

Throttle grip housing
24 * if necessary.333 33
and cable

housing and cable.
25 *Lights, signals and
switches33 3 3 3 3

PERIODIC MAINTENANCE AND ADJUSTMENT
6-7
6
EAU38262
TIP
Engine air filter and V-belt air filter
This model’s engine air filter is equipped with a disposable oil-coated paper element, which must not be cleaned
with compressed air to avoid damaging it.
The engine air filter element needs to be replaced and the V-belt air filter element needs to be serviced more fre-
quently when riding in unusually wet or dusty areas.
Hydraulic brake service
After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake
fluid levels and fill the reservoirs as required.
Every two years replace the internal components of the brake master cylinders and calipers, and change the bra-
ke fluid.
Replace the brake hoses every four years and if cracked or damaged.

TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4–1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
EAUS1701
Engine oil
The engine oil level should be chec-
ked before each ride. In addition, the
oil must be changed at the intervals
specified in the periodic maintenance
and lubrication chart and when the
service indicator light comes on.
To check the engine oil level
1. Place the scooter on the centers-
tand. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (wit-
hout screwing it in), and then
remove it again to check the oil
level.
TIP
The engine oil should be between the
minimum and maximum level marks.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil (with or
without oil filter element
replacement)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
1
3
2
1
ZAUM0685
Tightening torque:
Spark plug:

PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6

3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
1. Engine oil drain bolt
4. Check the drain bolt washer for
damage and replace it if neces-
sary.
1. Engine oil drain bolt
2. Washer
TIP
Skip steps 5–9 if the oil filter element
is not being replaced.
5. Remove the oil filter element
cover by removing the bolts.
1. Oil filter element cover
6. Remove the oil filter element and
O-ring.
1. Oil filter element
2. O-ring
3. Oil filter element cover
7. Check the O-ring for damage and
replace it if necessary.
8. Install the new oil filter element
and an O-ring.
9. Install the oil filter element cover
by installing the bolts, then tigh-
tening them to the specified tor-
que.
Tightening torque:
Oil filter cover bolt:

1
2
3
ZAUM0712
ZAUM07111
ZAUM07021
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
6