change wheel YAMAHA XMAX 250 2007 Owners Manual

DECLARATION of CONFORMITY
WeCompany: MORIC CO., LTD.
Address: 1450-6 Mori Mori-Machi Shuchi-gun Shizuoka 437-0292 Japan
Hereby declare that the product:
Kind of equipment: IMMOBILIZER
Type-designation: 5SL-00
is in compliance with following norm(s) or documents:
R&TTE Directive(1999/5/EC)
EN300 330-2 v1.1.1(2001-6), EN60950-1(2001)
Two or Three-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC)
Place of issue: Shizuoka, Japan
Date of issue: 1 Aug. 2002
Revolution record
No. Contents Date
To change contact person and integrate type-designation. 9 Jun. 2005
General manager of quality assurance div.
representative name and signature
MORIC CO., LTD.1450-6 Mori-machi Shuchi-gun Shizuoka 437-0292 JAPAN Telephone +81-538-85-0757 Facsimile +81-538-85-0456URL:http://www.moric-jp.com
1Version up the norm of EN60950 to EN60950-1 27 Feb. 20062
1C0-F8199-E3.qxd 2/11/06 20:46 Página 2

The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the footboard
during operation to maintain
control of the scooter.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger foo-
trests.
• Never carry a passenger
unless he or she can firmly pla-
ce both feet on the passenger
footrests.
Never ride under the influence of
alcohol or other drugs.
This scooter is designed for on-
road use only. It is not suitable for
off-road use.
Protective apparel
The majority of fatalities from scooter
accidents are the result of head inju-
ries. The use of a safety helmet is the
single most critical factor in the pre-
vention or reduction of head injuries.
Always wear an approved hel-
met.
Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impair-
ment of vision which could delay
seeing a hazard.
The use of a jacket, substantial
shoes, trousers, gloves, etc., is
effective in preventing or redu-
cing abrasions or lacerations.
Never wear loose-fitting clothes,
otherwise they could catch on
the control levers or wheels and
cause injury or an accident.
Never touch the engine or
exhaust system during or after
operation. They become very hot
and can cause burns. Always
wear protective clothing that
covers your legs, ankles, and
feet.
Passengers should also observe
the above precautions.
Modifications
Modifications made to this scooter
not approved by Yamaha, or the
removal of original equipment, may
render the scooter unsafe for use andmay cause severe personal injury.
Modifications may also make your
scooter illegal to use.
Loading and accessories
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution
of the scooter is changed. To avoid
the possibility of an accident, use
extreme caution when adding cargo
or accessories to your scooter. Use
extra care when riding a scooter that
has added cargo or accessories. Here
are some general guidelines to follow
if loading cargo or adding accessories
to your scooter:
Loading
The total weight of the operator, pas-
senger, accessories and cargo must
not exceed the maximum load limit.
When loading within this weight limit,
keep the following in mind:
Cargo and accessory weight
should be kept as low and close
Maximum load:
180 kg (396.9 lb)
1
SAFETY INFORMATION
1-2
1C0-F8199-E3.qxd 2/11/06 20:46 Página 9

ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
8* Brake hose • Check for cracks or damage.
√√√√ √• Replace. Every 4 years
9*Wheels • Check runout and for damage. √√√√
• Check tread depth and for damage.
10 * Tires • Replace if necessary.
√√√√ √
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings • Check bearing for looseness or damage. √√√√
12 *Steering bearings • Check bearing play and steering for roughness.
√√ √ √√• Lubricate with lithium-soap-based grease. Every 20000 km
13 * Chassis fasteners • Make sure that all nuts, bolts and screws are
properly tightened. √√√√ √
14 Sidestand, centerstand • Check operation.
• Lubricate. √√√√ √
15 *
Sidestand switch • Check operation. √√ √ √√ √
16 *Front fork • Check operation and for oil leakage. √√√√
17 * Shock absorber
assemblies • Check operation and shock absorbers for oil leakage.
√√√√
18 *Fuel injection • Check engine idle speed. √√ √ √√ √
• Change. (See pages 6-8.) √When the oil change indicator flashes
19
Engine oil (every 3000 km)• Check oil level and vehicle for oil leakage. Every 3000 km
√
20 *Engine oil strainer • Clean. √
21 *Cooling system • Check coolant level and vehicle for coolant leakage.
√√√√ √
• Change. Every 3 years
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
1C0-F8199-E3.qxd 10/1/07 18:13 Página 11

6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten
the oil filler cap.
EWA11310
s s
WARNING
Make sure that no foreign
material enters the final trans-
mission case.
Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAUS1272
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level through
the check window.
1. Maximum level mark
2. Minimum level mark
3. Coolant level window
NOTE:
The coolant should be between the
minimum and maximum level marks.
3. If the coolant is at or below the
minimum level mark, remove the
right floorboard mat by pulling it
up.
4. Open the reservoir cap, and then
add coolant to the maximum
level mark.
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.25 L (0.26 US qt) (0.22 Imp.qt)
Tightening torque:
Final transmission oil drain bolt:
22 Nm (2.2 m•kgf, 15.9 ft•lbf)
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6
1C0-F8199-E3.qxd 2/11/06 20:46 Página 18

EAU21960
Cast wheels
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
The wheel rims should be chec-
ked for cracks, bends or warpage
before each ride. If any damage
is found, have a Yamaha dealer
replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or crac-
ked wheel must be replaced.
The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for
it to develop its optimal characte-
ristics.
EAU33453
Front and rear brake lever
free play
Front
RearThere should be no free play at the
brake lever ends. If there is free play,
have a Yamaha dealer inspect the
brake system.EWA14211
s s
WARNING
A soft or spongy feeling in the bra-
ke lever can indicate the presence
of air in the hydraulic system. If the-
re is air in the hydraulic system,
have a Yamaha dealer bleed the
system before operating the vehi-
cle. Air in the hydraulic system will
diminish the braking performance,
which may result in loss of control
and an accident.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
6
1C0-F8199-E3.qxd 2/11/06 20:46 Página 24

DimensionsOverall length2210 mm (87.0 in)
Overall width 790 mm (31.1 in)
Overall height 1380 mm (54.3 in)
Seat height 785 mm (30.9 in)
Wheelbase 1545 mm (60.8 in)
Ground clearance 112.7 mm (4.44 in)
Minimum turning radius 3650 mm (143.7 in)
WeightWith oil and fuel176 kg (388 lb)
EngineEngine typeLiquid cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 249.7 cm
3(15.24 cu*in)
Bore x stroke 69.0 x 66.8 mm (2.71 x 2.63 in)
Compression ratio 10:01
Starting system Electric starter
Lubrication system Wet sump
Oil type or gradeEngine oilSAE 10W30
Recommended engine oil grade API service SE, SF, SG type or higher
Engine oil quantityPeriodic oil change1.2 L (1.27 US qt) (1.06 Imp qt)
Final transmission oilTypeYAMALUBE 4 (10W30) of SAE10W30
type SE motorolie
Quantity 0.25 L (0.26 US qt) (0.22 Imp qt)
Cooling systemRadiator capacity (including all routes)0.34 L (0.36 US qt) (0.30 Imp qt)
Coolant reservoir capacity (up to the
maximum level mark) 0.26 L (0.23 Imp qt, 0.28 US qt)
Air filterAir filter elementDry element
Recommended fuelRecommended fuelUnleaded fuel
Fuel tank capacity 12.5 L (3.30 US gal) (2.75 Imp gal)
Fuel reserve amount 2 L (0.53 US gal) (0.44 Imp gal)
Fuel injectionManufacturerAISAN Type x quantity
EFI System x 1
Spark plug (s)Manufacturer/modelNGK/DPR8EA-9
Spark plug gap 0.8-0.9 mm (0.031-0.035 in)
ClutchClutch typeDry, automatic centrifugal
TransmissionPrimary reduction systemHelical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 40/14 (2.857)
Transmission type V-belt automatic
Operation Centrifugal automatic type
ChassisFrame typeSteel tube underbone
Caster angle 28 º
Trail 100 mm (3.94 in)
Front tireTypeTubeless
SPECIFICATIONS
8-1
8
1C0-F8199-E3.qxd 16/11/06 19:33 Página 1