wheel YAMAHA XT500E 2000 User Guide

6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
93.Remove the swingarm end bolts.
4.Elevate the rear wheel by placing
a suitable stand under the
engine.
1
1
1.Swingarm end bolt (´2)
EAU00963*
Rear wheel removal
EW000122
w8
8
It is advisable to have a
Yamaha dealer service the
wheel.
8 8
Securely support the motorcy-
cle so there is no danger of it
falling over.1.Remove the axle nut.
2.Loosen the caliper bracket bolt.
2
1
1.Axle nut
2.Caliper bracket bolt
Tightening torque:
Axle holder nut:
9 Nm (0.9 m
0kg)
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 36

6-36
INSTRUMENT AND CONTROL FUNCTIONS
1
2
4
56
7
8
9
EAU01008
TroubleshootingAlthough Yamaha motorcycles
receive a rigid inspection before ship-
ment from the factory, trouble may
occur during operation.
Any problem in the fuel, compres-
sion, or ignition systems can cause
poor starting and loss of power. The
troubleshooting chart describes a
quick, easy procedure for making
checks.
If your motorcycle requires any
repair, bring it to a Yamaha dealer.
The skilled technicians at a Yamaha
dealership have the tools, experi-
ence, and know-how to properly ser-
vice your motorcycle. Use only gen-
uine Yamaha parts on your
motorcycle. Imitation parts may look
like Yamaha parts, but they are often
inferior. Conse-quently, they have a
shorter service life and can lead to
expensive repair bills.
5.Push the wheel forward and
remove the drive chain.
6.Pull out the wheel axle, then
remove the wheel assembly by
pulling backwards.NOTE:
8Do not depress the brake pedal
when the disc and caliper are
separated.
8You do not have to disassemble
the chain in order to remove or
install the rear wheel.
EAU01136*
Rear wheel installation1.Install the rear wheel and chain.
Guide the brake disc between
the brake pads. Make sure there
is enough gap between the
brake pads before inserting the
brake disc.
2.Make sure the wheel axle is
inserted from the left-hand side
and that the chain adjusting
plates are installed with the
punched side outward.
3.Install the swingarm end bolts.
4.Adjust the drive chain.
5.Tighten the following parts to the
specified torque.
Tightening torque:
Axle nut:
105 Nm (10.5 m
0kg)
Caliper bracket bolt:
48 Nm (4.8 m
0kg)
Swingarm end bolt:
2.5 Nm (0.25 m0kg)
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 37

7-1
CareThe exposure of its technology
makes a motorcycle charming but
also vulnerable. Although high-quality
components are used, they are not
all rust-resistant. While a rusty
exhaust pipe may remain unnoticed
on a car, it does look unattractive on
a motorcycle. Frequent and proper
care, however, will keep your motor-
cycle looking good, extend its life and
maintain its performance. Moreover,
the warranty states that the vehicle
must be properly taken care of. For
all these reasons, it is recommended
that you observe the following clean-
ing and storing precautions.Before cleaning
1.Cover up the muffler outlet with a
plastic bag.
2.Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.
3.Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
tooth or bottle brush, but never
apply such products onto seals,
gaskets, sprockets, the drive
chain and wheel axles. Always
rinse the dirt and degreaser off
with water.Cleaning
After normal use
Remove dirt with warm water, a neu-
tral detergent and a soft clean
sponge, then rinse with plenty of
clean water. Use a brush for hard-to-
reach parts. Tougher dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few
minutes before cleaning.
ECA00010
cC8 8
Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If you do use
such products for hard-to-
remove dirt, do not leave it on
any longer than instructed,
then thoroughly rinse it off
with water, immediately dry
the area and apply a corrosion
protection spray.
EAU01518
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
94PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 2

7-2
8 8
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (cou-
plers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After riding in the rain, near the seaor on salt-sprayed roads.Since sea salt or salt sprayed on the
roads in the winter are extremely cor-
rosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads. (Salt sprayed
in the winter may remain on the roads
well into spring.)
1.Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.Be sure to apply a corrosion pro-
tection spray on all (even
chrome- and nickel-plated) metal
surfaces to prevent corrosion.
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 3

7-5
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9
6.Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
7.Check and, if necessary, correct
the tire air pressure, then raise
the motorcycle so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to pre-
vent the tires from becoming
degraded in one spot.
8.Cover up the muffler outlet with a
plastic bag to prevent moisture
from entering.9.Remove the battery and fully
charge it. Store it in a cool, dry
place and recharge it once a
month. Do not store the battery
in an excessively cold or warm
place (less than 0¡C or more
than 30¡C). For more informa-
tion, see
ÒBattery storageÓ in the
chapter ÒPERIODIC MAINTE-
NANCE AND MINOR
REPAIRSÓ.
NOTE:
Make any necessary repairs before
storing the motorcycle.
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 6

SPECIFICATIONS
1
2
3
4
5
6
78
9
Specifications
ModelXT500E/XT600E
Dimensions
Overall length2,220 mm
2.295 mm (N, S, CH only)
Overall width865 mm
825 mm (CH only)
Overall height1,205 mm
Seat height855 mm
Wheel base1,440 mm
Minimum ground clearance230 mm
Minimum turning radius2,300 mm
Basic weight (with oil and full
fuel tank)176 kg
172 kg (CH only)
Engine
Engine typeAir-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangementForward inclined single
cylinder
Displacement499 cm
3
595 cm
3
Bore
´Stroke87.0 ´84.0 mm (XT500E)
95.0 ´84.0 mm (XT600E)
Compression ratio8.5:1
Starting systemElectric starter
Lubrication systemDry sumpEngine oil
Type
Recommended engine oil
classificationAPI Service SE, SF, SG type
or higher
cCBe sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
ÒEnergy ConservingÓ) contain anti-friction additives which
will cause clutch and/or starter clutch slippage, resulting in
reduced component life and poor engine performance.
Capacity
Periodic oil change2.7 L
With oil filter replacement2.8 L
Total amount3.3 L
EAU01038
SPECIFICATIONS
8-1
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 8

SPECIFICATIONS
1
2
3
4
5
6
78
9
Air pressure (cold tire)
up to 90 kg load*
Front150 kPa (1.50 kg/cm
2, 1.50 bar)
Rear150 kPa (1.50 kg/cm2, 1.50 bar)
90 kg load ~ Maximum
load*
Front150 kPa (1.50 kg/cm2, 1.50 bar)
Rear225 kPa (2.25 kg/cm2, 2.25 bar)
Off-road riding
Front125 kPa (1.25 kg/cm2, 1.25 bar)
Rear125 kPa (1.25 kg/cm2, 1.25 bar)
High speed riding
Front150 kPa (1.50 kg/cm2, 1.50 bar)
Rear150 kPa (1.50 kg/cm2, 1.50 bar)
* Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
TypeSpoke wheel
Size21 ´1.85
Rear
TypeSpoke wheel
Size17 ´MT2.50 Brakes
Front
TypeSingle disc brake
OperationRight hand operation
FluidDOT 3 or DOT 4
Rear
TypeSingle disc brake
OperationRight foot operation
FluidDOT 4
Suspension
Front
TypeTelescopic fork
Rear
TypeSwingarm (new monocross)
Shock absorber
FrontCoil spring/oil damper
RearCoil spring/gas-oil damper
Wheel travel
Front225 mm
Rear200 mm
8-3
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 10

INDEX
Front brake lever free play
adjustment..........................................6-18
Front fork inspection..............................6-26
Front wheel installation..........................6-34
Front wheel removal..............................6-33
Fuel.........................................................3-6
Fuel cock.................................................3-7
Fuel tank cap...........................................3-6
Fuse replacement..................................6-29
H
Handlebar switches.................................3-3
Dimmer switch......................................3-3
Engine stop switch................................3-4
Horn switch...........................................3-3
Lights switch.........................................3-3
Pass switch...........................................3-3
Start switch...........................................3-4
Turn signal switch.................................3-3
Headlight bulb replacement...................6-29
Helmet holder..........................................3-9
High beam indicator light.........................3-2
Horn switch..............................................3-3
How to use the conversion table.............9-3
I
Identification number records..................9-1
Idle speed adjustment...........................6-14
Indicator lights.........................................3-2
High beam indicator light......................3-2
Neutral indicator light............................3-2
Turn indicator light................................3-2
Inspecting the brake fluid level..............6-21
K
Key identification number........................9-1
L
Lights switch............................................3-3
M
Main switch/Steering lock........................3-1
Model label..............................................9-2
N
Neutral indicator light...............................3-2
P
Panel A, B...............................................6-7
Parking....................................................5-6
Pass switch.............................................3-3
Periodic maintenance and
lubrication chart....................................6-3
Pre-operation check list...........................4-1
R
Rear brake pedal.....................................3-5
Rear brake pedal height adjustment.....6-19
Rear shock absorber adjustment..........3-10
Rear suspension lubrication..................6-26
Rear wheel installation..........................6-36
Rear wheel removal..............................6-35
Recommended shift point
(for Switzerland only)............................5-4
S
Seat.........................................................3-9
Shift pedal ..............................................3-5
Shifting....................................................5-4
Sidestand..............................................3-11
Sidestand lubrication.............................6-25
A
Air filter..................................................6-12
B
Battery...................................................6-28
Brake and clutch lever lubrication.........6-25
Brake and shift pedal lubrication...........6-25
Brake fluid replacement.........................6-22
Brake light switch adjustment................6-20
C
Cable inspection and lubrication...........6-24
Carburetor adjustment...........................6-13
Care.........................................................7-1
Carrier (optional)...................................3-11
Checking the front and rear brake
pads....................................................6-20
Clutch lever.............................................3-4
Clutch lever free play adjustment..........6-18
Cowling A................................................6-7
Cowling and panel removal and
installation.............................................6-6
D
Description..............................................2-1
Dimmer switch.........................................3-3
Drive chain lubrication...........................6-23
Drive chain slack adjustment.................6-23
Drive chain slack check.........................6-22
E
Engine break-in.......................................5-5
Engine oil...............................................6-10
Engine stop switch..................................3-4
F
Front brake lever.....................................3-5
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 16

INDEX
Sidestand/clutch switch operation
check..................................................3-12
Spark plug...............................................6-8
Specifications..........................................8-1
Speedometer...........................................3-2
Start switch..............................................3-4
Starter (choke).........................................3-8
Starting a warm engine...........................5-3
Starting the engine..................................5-1
Steering inspection................................6-27
Storage....................................................7-4
Supporting the motorcycle.....................6-32
T
Tachometer.............................................3-3
Taillight bulb replacement.....................6-32
Throttle cable and grip lubrication.........6-24
Throttle cable free play adjustment.......6-14
Tips for reducing fuel consumption.........5-5
Tires......................................................6-15
Tool kit.....................................................6-1
Troubleshooting.....................................6-36
Troubleshooting chart............................6-37
Turn indicator light...................................3-2
Turn signal light bulb replacement........6-31
Turn signal switch....................................3-3
V
Valve clearance adjustment..................6-15
Vehicle identification number..................9-1
W
Wheel bearings.....................................6-27
Wheels..................................................6-17
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 17