weight YAMAHA XT500E 2002 Owners Manual

6-16
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00635
Adjusting the throttle cable
free playThrottle cable free play, adjustingThe throttle cable free play should
measure 3–5 mm at the throttle grip.
Periodically check the throttle cable
free play and, if necessary, have a
Yamaha dealer adjust it.
a
a. Throttle cable free play
EAU04259
TiresTiresTo maximize the performance, dura-
bility, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EW000082
w8The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the tempera-
ture of the tires equals the
ambient temperature).
8The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passen-
ger, cargo, and accessories
approved for this model.
EAU00637
Adjusting the valve
clearanceValve clearance, adjustingThe valve clearance changes with
use, resulting in improper air-fuel mix-
ture and/or engine noise. To prevent
this from occurring, the valve clear-
ance must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
4PT-E7 (English) 6/29/01 9:13 AM Page 53

6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
68 8
Adjust the suspension and tire
air pressure with regard to the
load.
8Check the tire condition and
air pressure before each ride.
EWA00012
wBecause loading has an enormous
impact on the handling, braking,
performance and safety character-
istics of your motorcycle, you
should keep the following precau-
tions in mind.
8NEVER OVERLOAD THE
MOTORCYCLE! Operation of
an overloaded motorcycle may
result in tire damage, loss of
control, or severe injury. Make
sure that the total weight of
rider, passenger, cargo, and
accessories does not exceed
the specified maximum load
for the vehicle.
8Do not carry along loosely
packed items, which can shift
during a ride.
8Securely pack the heaviest
items close to the center of the
motorcycle and distribute the
weight evenly on both sides.
Tire air pressure
(measured on cold tires)
Load* Front Rear
Up to 90 kg150 kPa
(1.50 kgf/cm
2,
1.50 bar)150 kPa
(1.50 kgf/cm
2,
1.50 bar)
90 kg–
maximum150 kPa
(1.50 kgf/cm
2,
1.50 bar)225 kPa
(2.25 kgf/cm
2,
2.25 bar)
Off-road riding125 kPa
(1.25 kgf/cm
2,
1.25 bar)125 kPa
(1.25 kgf/cm
2,
1.25 bar)
High speed riding150 kPa
(1.50 kgf/cm
2,
1.50 bar)225 kPa
(2.25 kgf/cm
2,
2.25 bar)
Maximum load*176 kg (XT500E)
180 kg (XT600E)
* Total weight of rider, passenger, cargo and
accessories
4PT-E7 (English) 6/29/01 9:13 AM Page 54

6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00744
Drive chain slackDrive chain slackThe drive chain slack should be
checked before each ride and adjust-
ed if necessary.
To check the drive chain slackChecking1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:
When checking and adjusting the
drive chain slack, the motorcycle
should be positioned straight up and
there should be no weight on it.2. Shift the transmission into the
neutral position.
EAU01134
To adjust the drive chain slackadjusting1. Loosen the axle nut and the
brake caliper bracket bolt.
2. To tighten the drive chain, turn
the adjusting plate on each side
of the swingarm in direction a.
To loosen the drive chain, turn
the adjusting plate on each side
of the swingarm in direction b,
and then push the rear wheel for-
ward.
a
b2 1
3
1. Adjusting plate
2. Axle nut
3. Brake caliper bracket bolt
3. Move the rear wheel by pushing
the motorcycle to locate the tight-
est portion of the drive chain,
and then measure the drive
chain slack as shown.
4. If the drive chain slack is incor-
rect, adjust it as follows.
a
a. Drive chain slack
Drive chain slack:
30–40 mm
4PT-E7 (English) 6/29/01 9:13 AM Page 62

8-1
EAU01038
SPECIFICATIONS
8
SpecificationsSpecifications
Model XT500E/XT600E
Dimensions
Overall length 2,220 mm
2.295 mm (N, S, CH only)
Overall width 865 mm
825 mm (CH only)
Overall height 1,205 mm
Seat height 855 mm
Wheel base 1,440 mm
Ground clearance 230 mm
Minimum turning radius 2,300 mm
Basic weight (with oil and full
fuel tank)176 kg
172 kg (CH only)
Engine
Engine type Air-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangement Forward inclined single
cylinder
Displacement 499 cm
3
595 cm
3
Bore ×Stroke 87.0 ×84.0 mm (XT500E)
95.0 ×84.0 mm (XT600E)
Compression ratio 8.5:1
Starting system Electric starter
Lubrication system Dry sump
Engine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or highercCBe sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
“ENERGY CONSERVING II”) contain anti-friction additives
which will cause clutch and/or starter clutch slippage, result-
ing in reduced component life and poor engine performance.
Capacity
Without oil filter element
replacement 2.7 L
With oil filter element
replaced 2.8 L
Total amount (dry engine) 3.3 L
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
4PT-E7 (English) 6/29/01 9:13 AM Page 88

8-3
SPECIFICATIONS
8
Air pressure (cold tire)
up to 90 kg load*
Front 150 kPa (1.50 kgf/cm
2, 1.50 bar)
Rear 150 kPa (1.50 kgf/cm2, 1.50 bar)
90 kg load–Maximum
load*
Front 150 kPa (1.50 kgf/cm2, 1.50 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
Off-road riding
Front 125 kPa (1.25 kgf/cm2, 1.25 bar)
Rear 125 kPa (1.25 kgf/cm2, 1.25 bar)
High speed riding
Front 150 kPa (1.50 kgf/cm2, 1.50 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
* Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type Spoke wheel
Size 21 ×1.85
Rear
Type Spoke wheel
Size 17 ×MT2.50 or
17 M/C ×MT2.50Brakes
Front
Type Single disc brake
Operation Right hand
Fluid DOT 4
Rear
Type Single disc brake
Operation Right foot
Fluid DOT 4
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm (new monocross)
Shock absorber
Front Coil spring/oil damper
Rear Coil spring/gas-oil damper
Wheel travel
Front 225 mm
Rear 200 mm
4PT-E7 (English) 6/29/01 9:13 AM Page 90

8-5
SPECIFICATIONS
8
EAU03941
Conversion tableConversion table
Conversion tableAll specification data in this manual are listed in SI and
METRIC UNITS.
Use this table to convert METRIC unit data to
IMPERIAL unit data.
Ex.
METRIC MULTIPLIER IMPERIAL
** mm×0.03937 = ** in
2 mm×0.03937 = 0.08 in
METRIC TO IMPERIAL
Metric unit Multiplier Imperial unit
m•kgf 7.233 ft•lb
Torquem•kgf 86.794 in•lb
cm•kgf 0.0723 ft•lb
cm•kgf 0.8679 in•lb
Weightkg 2.205 lbg 0.03527 oz
Speed km/hr 0.6214 mph
km 0.6214 mi
m 3.281 ft
Distance m 1.094 yd
cm 0.3937 in
mm 0.03937 in
cc (cm
3) 0.03527 oz (IMP liq.)
Volume, cc (cm3) 0.06102 cu•in
capacity L (liter) 0.8799 qt (IMP liq.)
L (liter) 0.2199 gal (IMP liq.)
kgf/mm 55.997 lb/in
Misc. kgf/cm
2
14.2234 psi (lb/in
2)
Centigrade (°C)
9/5 + 32
Fahrenheit (°F)
CONVERSION TABLE
4PT-E7 (English) 6/29/01 9:13 AM Page 92