brake YAMAHA XT660Z 2011 User Guide

This ABS has a test mode which
allows the owner to experience
the pulsating at the brake lever or
brake pedal when the ABS is
operating. However, special tools
are required, so please consult
your Yamaha dealer when perfor-
ming this test.
ECA16120
Keep any type of magnets (inclu-
ding magnetic pick-up tools, mag-
netic screwdrivers, etc.) away from
the front and rear wheel hubs,
otherwise the magnetic rotors
equipped in the wheel hubs may be
damaged, resulting in improper
performance of the ABS system.
1. Front wheel hub
1. Rear wheel hub
EAU13074
Fuel tank cap
1. Lock cover
2. Open
To open the fuel tank cap
Open the fuel tank cap lock cover,
insert the key into the lock, and then
turn it 1/4 turn clockwise. The lock will
be released and the fuel tank cap can
be opened.
To close the fuel tank cap
1. Push the fuel tank cap into posi-
tion with the key inserted in the
lock.
2. Turn the key counterclockwise to
the original position, remove it,
and then close the lock cover.
NOTICE
INSTRUMENT AND CONTROL FUNCTIONS
3-13
3
56P-F8199-E0 30/6/10 09:24 Página 31

FOR YOUR SAFETY – PRE-OPERATION CHECKS
4-1
4
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the ins-
pection and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment dama-
ge. Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures pro-
vided in this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
WARNING
ITEM CHECKS PAGE
• Check fuel level in fuel tank.
• Refuel if necessary.
Fuel• Check fuel line for leakage. 3-14
• Check the fuel tank breather/overflow hose for obstructions, cracks or
damage, and check the hose connection.
• Check oil level in oil tank.
Engine oil• If necessary, add recommended oil to specified level. 6-11
• Check vehicle for oil leakage.
• Check coolant level in reservoir.
Coolant• If necessary, add recommended coolant to specified level. 6-14
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check lever free play.
• Adjust if necessary.
Front brake• Check brake pads for wear. 6-21
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
56P-F8199-E0 30/6/10 09:24 Página 40

ITEM CHECKS PAGE
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Rear brake• Replace if necessary. 6-21
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
Clutch• Lubricate cable if necessary.
6-20
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
Throttle grip• Check cable free play.
6-17, 6-25
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable
and grip housing.
Control cables• Make sure that operation is smooth.
• Lubricate if necessary.6-25
• Check chain slack.
Drive chain• Adjust if necessary.
6-23, 6-24
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
Wheels and tires• Check tire condition and tread depth.
6-17, 6-19
• Check air pressure.
• Correct if necessary.
Brake pedal• Make sure that operation is smooth.
• Lubricate pedal pivoting point if necessary.6-26
Brake and clutch levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.6-25
Sidestand• Make sure that operation is smooth.
• Lubricate pivot if necessary.6-26
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.—
Instruments, lights, signals • Check operation.
and switches• Correct if necessary.—
FOR YOUR SAFETY – PRE-OPERATION CHECKS
4-2
4
56P-F8199-E0 30/6/10 09:24 Página 41

PERIODIC MAINTENANCE AND ADJUSTMENT
6-1
6
EAU17243
Periodic inspection, adjustment, and
lubrication will keep your vehicle in
the safest and most efficient condi-
tion possible. Safety is an obligation
of the vehicle owner/operator. The
most important points of vehicle ins-
pection, adjustment, and lubrication
are explained on the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a general guide under
normal riding conditions. However,
depending on the weather, terrain,
geographical location, and individual
use, the maintenance intervals may
need to be shortened.
EWA10321
Failure to properly maintain the
vehicle or performing maintenance
activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle
service, have a Yamaha dealer per-
form service.
EWA15121
Turn off the engine when perfor-
ming maintenance unless otherwi-
se specified.
A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Running the engine while servi-
cing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-1 for more
information about carbon
monoxide.
EWA15460
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before tou-
ching them.
EAU17381
Owner’s tool kit
1. Owner’s tool kit
The owner’s tool kit is located under
the seat. (See page 3-16).
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to
assist you in the performance of pre-
ventive maintenance and minor
repairs. However, additional tools
such as a torque wrench may be
necessary to perform certain mainte-
nance work correctly.
WARNING
WARNING
WARNING
56P-F8199-E0 30/6/10 09:24 Página 47

PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
6
EAU1770C
General maintenance and lubrication chart
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
1Air filter element• Replace.√√
2Clutch• Check operation.
• Adjust.√√ √ √ √
3*Front brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
4*Rear brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
5*Brake hoses• Check for cracks or damage.√√√ √√• Replace. Every 4 years
• Check runout, spoke tightness
6*Wheelsand for damage.√√ √ √ √
• Tighten spokes if necessary.
• Check tread depth and for
damage.
7*Tires• Replace if necessary.√√√ √√
• Check air pressure.
• Correct if necessary.
8*Wheel bearings• Check bearing for looseness or
damage.√√√ √
56P-F8199-E0 30/6/10 09:24 Página 50

PERIODIC MAINTENANCE AND ADJUSTMENT
6-5
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
9*Swingarm• Check operation and for
excessive play.√√√ √
• Lubricate with lithium-soap-
based grease.Every 50000 km (30000 mi)
• Check chain slack, alignment
and condition.
Every 500 km (300 mi) and after washing the motorcycle,
10Drive chain• Adjust and lubricate chain with a
special O-ring chain lubricant riding in the rain or riding in wet areas
thoroughly.
• Check bearing play and steering
11 *Steering bearingsfor roughness.√√ √ √ √
• Lubricate with lithium-soap-
based grease.Every 20000 km (12000 mi)
12 *Chassis fasteners• Make sure that all nuts, bolts and
screws are properly tightened.√√√ √√
13Brake lever pivot
shaft• Lubricate with silicone grease.√√√ √√
14Brake pedal pivot
shaft• Lubricate with silicone grease.√√√ √√
15Clutch lever pivot • Lubricate with lithium-soap-
shaftbased grease.√√√ √√
• Check operation.
16Sidestand• Lubricate with lithium-soap-√√√ √√
based grease.
17 *Sidestand switch• Check operation.√√ √ √ √ √
56P-F8199-E0 30/6/10 09:24 Página 51

PERIODIC MAINTENANCE AND ADJUSTMENT
6-6
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
18 *Front fork• Check operation and for oil
leakage.√√√ √
19 *Shock absorber • Check operation and shock
assemblyabsorber for oil leakage.√√√ √
Rear suspension• Check operation.√√√ √
20 *relay arm and
• Lubricate with lithium-soap-
connecting arm
√√
pivoting pointsbased grease.
• Change.
21Engine oil• Check oil level and vehicle for √√ √ √ √ √
oil leakage.
22Engine oil filter
element• Replace.√√ √
• Check coolant level and vehicle
23 *Cooling systemfor coolant leakage.√√√ √√
• Change. Every 3 years
24 *Front and rear brake
switches• Check operation.√√ √ √ √ √
25Moving parts and
cables• Lubricate.√√√ √√
• Check operation and free play.
Throttle grip • Adjust the throttle cable free
26 *housingplay if necessary.√√√ √√
and cable• Lubricate the throttle grip housing
and cable.
56P-F8199-E0 30/6/10 09:24 Página 52

PERIODIC MAINTENANCE AND ADJUSTMENT
6-7
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
27 *Lights, signals and • Check operation.
switches• Adjust headlight beam.√√ √ √ √ √
EAUM1890
TIP
Replace the air filter element more frequently if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
56P-F8199-E0 30/6/10 09:24 Página 53

PERIODIC MAINTENANCE AND ADJUSTMENT
6-19
6
EWA10570
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
motorcycle with excessively
worn tires decreases riding
stability and can lead to loss of
control.
The replacement of all wheel-
and brake-related parts, inclu-ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
It is not recommended to patch
a punctured tube. If unavoida-
ble, however, patch the tube
very carefully and replace it as
soon as possible with a high-
quality product.
EAU21942
Spoke wheelsEWA10610
The wheels on this model are not
designed for use with tubeless
tires. Do not attempt to use tube-
less tires on this model.
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
The wheel rims should be chec-
ked for cracks, bends or warpa-
ge, and the spokes for looseness
or damage before each ride. If
any damage is found, have a
Yamaha dealer replace the whe-
el. Do not attempt even the sma-
llest repair to the wheel. A defor-
med or cracked wheel must be
replaced.
The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
WARNING
WARNING
Front tire:
Size:
XT660Z 90/90-21M/C 54S
XT660Z 90/90-21M/C 54T
XT660ZA 90/90-21M/C 54S
Manufacturer/model:
XT660Z METZELER/ TOURANCE
XT660Z MICHELIN/SIRAC
XT660ZA PIRELLI/SCORPION
TRAIL
Rear tire:
Size:
XT660Z 130/80-17M/C 65S
XT660Z 130/80-17M/C 65T
XT660ZA 130/80-17M/C 65S
Manufacturer/model:
XT660Z METZELER/ TOURANCE
XT660Z MICHELIN/SIRAC
XT660ZA PIRELLI/SCORPION
TRAIL
56P-F8199-E0 30/6/10 09:24 Página 65

EAU22392
Checking the front and rear
brake pads
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU22420
Front brake pads
1. Wear indicator groove
Each front brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the
wear indicator groove has almostdisappeared, have a Yamaha dealer
replace the brake pads as a set.
EAU22500
Rear brake pads
1. Lining thickness
Check each rear brake pad for dama-
ge and measure the lining thickness.
If a brake pad is damaged or if the
lining thickness is less than 10 mm
(0.04 in), have a Yamaha dealer repla-
ce the brake pads as a set.
EAU38640
Checking the brake fluid
level
Front brake
1. Minimum level mark
Rear brake (for XT660Z)
1. Minimum level mark
PERIODIC MAINTENANCE AND ADJUSTMENT
6-21
6
56P-F8199-E0 30/6/10 09:24 Página 67